---------------------------------------------------------- RV9-List Digest Archive --- Total Messages Posted Sat 01/31/04: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 06:58 AM - Re: Wire runs through center section (david edgemon) 2. 11:04 AM - [ Greg Gruninger ] : New Email List Photo Share Available! (Email List Photo Shares) 3. 11:05 AM - [ Rob Ray ] : New Email List Photo Share Available! (Email List Photo Shares) 4. 11:18 AM - [ Jerry Calvert ] : New Email List Photo Share Available! (Email List Photo Shares) 5. 04:57 PM - RV-9A Kit For Sale (Fabian Lefler) ________________________________ Message 1 _____________________________________ Time: 06:58:05 AM PST US From: david edgemon Subject: RV9-List: Re: Wire runs through center section --> RV9-List message posted by: david edgemon Mathew, I finished my wiring over the holidays and did indeed drill a few extra holes for wiring. A lot depends on what you are doing with electronics back in the tail. Here's what I did. 1. I have the MANUAL elevator trim so no servo wiring but it takes up one side of the center tunnel. I placed the strobe supply in the baggage area plus I had wires for the Dynon external magnetometer going to the tail. 2. I ran wiing for the magnetometer and power for the strobe supply in the center tunnel along with the manual trim cable. 3. I drill holes for snap bushings along both sides of the fuse down along the area where the flap pushrods go. This allowed me to run the wing strobe cables under the fuselag floor and out the aileron pushrod hole and down the wing. I used 5/8 inch snap bushings which gave plenty of extra room for the other odds and ends that you'll forget about until its time to run wires. Good Luck P.S. Oh yeah, I also drilled an additional snap bushing hole in the spar center section in order to pass the wiring going to the center tunnel area and out the wings. I ended up building a main wiring bundle that drops down the firewall alongside the cabin heater vent area and then runs alongside the fuel and brake lines. These wires then split up at the spar with most going through to the floor area and either out the wings or to the tail. Hope it helps >--> RV9-List message posted by: "Matthew Brandes" > >I'm starting on my fuselage center section and I've read where most people >wish they would have drilled additional holes for wiring runs. > >Ok.. where would you have put them??? I'd like to benefit from those of >have gone before me and drill them now instead of later. > >Matthew Brandes >Van's RV-9A (Wings/Fuselage) >EAA Chapter 91 & 868 >www.n523rv.com > > -- David Edgemon Summit Research Corp. "Under system requirements it said install Windows 95 or better, so I installed Linux" Anonymous ________________________________ Message 2 _____________________________________ Time: 11:04:43 AM PST US Subject: RV9-List: [ Greg Gruninger ] : New Email List Photo Share Available! From: Email List Photo Shares --> RV9-List message posted by: Email List Photo Shares A new Email List Photo Share is available: Poster: Greg Gruninger Subject: Completed RV-8! http://www.matronics.com/photoshare/GGrun5673@gbronline.com.01.31.2004/index.html o Main Photo Share Index http://www.matronics.com/photoshare o Submitting a Photo Share If you wish to submit a Photo Share of your own, please include the following information along with your email message and files: 1) Email List or Lists that they are related to: 2) Your Full Name: 3) Your Email Address: 4) One line Subject description: 5) Multi-line, multi-paragraph description of topic: 6) One-line Description of each photo or file: Email the information above and your files and photos to: pictures@matronics.com ________________________________ Message 3 _____________________________________ Time: 11:05:00 AM PST US Subject: RV9-List: [ Rob Ray ] : New Email List Photo Share Available! From: Email List Photo Shares --> RV9-List message posted by: Email List Photo Shares A new Email List Photo Share is available: Poster: Rob Ray Subject: RV-FOUR (Editor's Note: WOW!!) http://www.matronics.com/photoshare/smokyray@yahoo.com.01.31.2004/index.html o Main Photo Share Index http://www.matronics.com/photoshare o Submitting a Photo Share If you wish to submit a Photo Share of your own, please include the following information along with your email message and files: 1) Email List or Lists that they are related to: 2) Your Full Name: 3) Your Email Address: 4) One line Subject description: 5) Multi-line, multi-paragraph description of topic: 6) One-line Description of each photo or file: Email the information above and your files and photos to: pictures@matronics.com ________________________________ Message 4 _____________________________________ Time: 11:18:52 AM PST US Subject: RV9-List: [ Jerry Calvert ] : New Email List Photo Share Available! From: Email List Photo Shares --> RV9-List message posted by: Email List Photo Shares A new Email List Photo Share is available: Poster: Jerry Calvert Subject: Leather Interior http://www.matronics.com/photoshare/rv6@cox.net.01.31.2004/index.html o Main Photo Share Index http://www.matronics.com/photoshare o Submitting a Photo Share If you wish to submit a Photo Share of your own, please include the following information along with your email message and files: 1) Email List or Lists that they are related to: 2) Your Full Name: 3) Your Email Address: 4) One line Subject description: 5) Multi-line, multi-paragraph description of topic: 6) One-line Description of each photo or file: Email the information above and your files and photos to: pictures@matronics.com ________________________________ Message 5 _____________________________________ Time: 04:57:54 PM PST US From: "Fabian Lefler" Subject: RV9-List: RV-9A Kit For Sale --> RV9-List message posted by: "Fabian Lefler" It is with a heavy heart I post this message to the various lists. Personal issues (not financial) are forcing me to sell my beloved RV-9A kit. I have labored over this kit for the past 3 years, and consider it to be a very well built and good looking airplane. I would love to sell it to someone in the area who can appreciate some occasional, and FREE, help from me to complete the kit. THIS AIRPLANE COULD BE FLYING IN LESS THAN A COUPLE OF MONTHS. You can see some photos and detailed description here: http://www.affordablepanels.com/rv9aforsale.htm The Kit Includes: -Eggenfellner Firewall Forward Package - Normally Aspirated (Installed). -MT 3 Blade Propeller (Still in Crate). -Altrak Altitude Hold (Installed). -Trio Avionics Autopilot (Installed). -Aeroflash Nav and Strobe Lighting. -Interior by Cleveland Tools with plenty of extra fabric. -Fuselage is on its gear and Canopy Work is finished with all skirts installed. -Modular Panel (Installed), but no instrument holes have been cut out. -Much more. Please NO E-MAILS. If you are interested, please call me at 561-641-9737 Thank You Fabian