Today's Message Index:
----------------------
1. 10:07 AM - 9A gear weldment (Paul Eastham)
2. 10:16 AM - Re: Small celebration for me (Chuck Weyant)
3. 01:38 PM - Gelcoat (plaurence@the-beach.net)
4. 07:29 PM - Re: 9A gear weldment (Sargentclt@cs.com)
5. 08:55 PM - Re: 9A gear weldment (Paul Eastham)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | 9A gear weldment |
--> RV9-List message posted by: Paul Eastham <eastham@netapp.com>
Hi all,
Has anyone noticed an interference problem on the main gear weldments?
The bottom-most rivet on the side skins through the center section
seems to intersect with the weldment flange that takes the 5 bolts.
Here's a picture:
http://hmb.dyndns.org/~eastham/rv/images/20040813_IMG_1219.JPG
Seems like the safest thing to do is remove it and relieve the
weldment -- wish I hadn't bolted it in yet! Those bolts at the bottom
sure are hard to work on, and the seat pan platnuts make removal very
difficult.
If you haven't gotten this far yet I'd highly recommend
figuring this out before installation...I'll post Van's response
as well when they get back to me.
Paul
http://hmb.dyndns.org/~eastham/rv
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Small celebration for me |
--> RV9-List message posted by: "Chuck Weyant" <cweyant@chuckdirect.com>
Keep at 'er Bill. I finally went into the paint shop last week. Jeez, I
suddenly have nothing to do and I've run out of my favorite excuse for not
going to wifey, boring functions: "Sorry Hon, have to work on the plane
tonight." She's fired the gardner now that "I'm freed up again" and I'm
scheduled for the next Chamber meeting next week. Hmmm, that RV10 kit
looks pretty interesting...
Chuck W. SLO Build 9A
----- Original Message -----
From: "Bill Repucci" <bill@repucci.com>
Subject: RV9-List: Small celebration for me
> --> RV9-List message posted by: "Bill Repucci" <bill@repucci.com>
>
> After 672 hours of building, I finally pulled the right wing off the jig
> and celebrated by cleaning up my shop.
> While waiting for some bucking help to show up this summer, I completed
> both flaps and ailerons.
>
> Next week I order the fuselage kit.
>
> Bill R.
> RV-9
> SN: 90737
> N941WR (Reserved)
> www.repucci.com/bill/baf.html
>
> Do not archive
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> RV9-List message posted by: plaurence@the-beach.net
Listers,
Has anyone sanded the gelcoat off the fiberglass end caps on the rudder, verticle
stab ect. I know that gelcoat tends to crack after a period of time.
Any advice on this is appreciated
Peter
RV9A
waiting for wings
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 9A gear weldment |
--> RV9-List message posted by: Sargentclt@cs.com
I have a 7A and I remember somewhere the rivet call out is to double flush
this one and the one on the other side as well. By your picture you don't have
the gear bracket bolted in. The rivet goes inside out BTW
I think this will solve your interfearance problem
Tad Sargent
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 9A gear weldment |
--> RV9-List message posted by: Paul Eastham <eastham@netapp.com>
Well, my blueprint shows a universal head rivet and no note for
double-flush or inside-out in that location. I don't think
inside-out would be sufficient to solve the problem.
On Sun, Aug 15, 2004 at 10:29:10PM -0400, Sargentclt@cs.com wrote:
> --> RV9-List message posted by: Sargentclt@cs.com
>
> I have a 7A and I remember somewhere the rivet call out is to double flush
> this one and the one on the other side as well. By your picture you don't have
> the gear bracket bolted in. The rivet goes inside out BTW
>
> I think this will solve your interfearance problem
> Tad Sargent
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|