Today's Message Index:
----------------------
 
     1. 12:48 PM - Bending the flanges on the elevator trim tab (smittysrv)
     2. 01:05 PM - Re: Bending the flanges on the elevator trim tab (Chenoweth)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
12:48:44 PM PST US
Subject: 
Bending the flanges on the elevator trim tab
From: 
"smittysrv" <smitty@smittysrv.com>
      
      --> RV9-List message posted by: "smittysrv" <smitty@smittysrv.com>
      
      I was following the instructions on building the rv-9a trim tab to the letter.
      It said to rivet the trim tab horns to the trim tab skin. Now it says to bend
      the outer flanges of the trim tab skin. How can you do this with the trim tab
      horns riveted on?
      
      Thanks!
      
      --------
      Smittys RV-9A
      
      
      
      
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=10431#10431
      
      
      
      
      
      
      
      
      
      
      
      
       
       
       
      
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
01:05:02 PM PST US
From: 
"Chenoweth" <chenoweth@gwi.net>
Subject: 
Re: Bending the flanges on the elevator trim tab
      
      --> RV9-List message posted by: "Chenoweth" <chenoweth@gwi.net>
      
      I bent first and riveted the horns second - this produced its own challenge
      riveting along the edge of the bend.
      I needed two tries to get this done well and the key seemed to be to make a
      bending block EXACTLY as shown in the photo; clamped as shown.
      Bill
      RV9 - fuselage arrives this week.
      ----- Original Message ----- 
      From: "smittysrv" <smitty@smittysrv.com>
      Sent: Monday, February 06, 2006 3:44 PM
      Subject: RV9-List: Bending the flanges on the elevator trim tab
      
      
      > --> RV9-List message posted by: "smittysrv" <smitty@smittysrv.com>
      >
      > I was following the instructions on building the rv-9a trim tab to the
      letter. It said to rivet the trim tab horns to the trim tab skin. Now it
      says to bend the outer flanges of the trim tab skin. How can you do this
      with the trim tab horns riveted on?
      >
      > Thanks!
      >
      > --------
      > Smittys RV-9A
      >
      >
      > Read this topic online here:
      >
      > http://forums.matronics.com/viewtopic.php?p=10431#10431
      >
      >
      
      
      
      
      
      
      
      
       
       
       
      
      
      








Other Matronics Email List Services




Post A New Message
  
rv9-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV9-List.htm
Full Archive Search Engine
  
http://www.matronics.com/search
7-Day List Browse
  
http://www.matronics.com/browse/rv9-list
Browse RV9-List Digests
  
http://www.matronics.com/digest/rv9-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --