---------------------------------------------------------- RV9-List Digest Archive --- Total Messages Posted Mon 05/08/06: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:21 AM - aileron push tubes (Peter Laurence) 2. 08:35 AM - Re: aileron push tubes (Neilekins@aol.com) 3. 09:15 AM - Re: aileron push tubes (jc@INFONET.COM.BR) 4. 10:31 AM - Re: aileron push tubes (Peter Laurence) 5. 08:06 PM - [ Richard Dudley ] : New Email List Photo Share Available! (Email List Photo Shares) ________________________________ Message 1 _____________________________________ Time: 08:21:11 AM PST US From: " Peter Laurence" Subject: RV9-List: aileron push tubes --> RV9-List message posted by: " Peter Laurence" Question for those of you that have installed the Stick to aileron bellcrank push tubes. Did you cut them as per Van's measurments before installing. If so, were the measurments correct or were you "VANdalized"? Peter Laurence 9A fuse ________________________________ Message 2 _____________________________________ Time: 08:35:07 AM PST US From: Neilekins@aol.com Subject: Re: RV9-List: aileron push tubes --> RV9-List message posted by: Neilekins@aol.com I cut them as per plans. I would add 1/4 inch to them. I had just enough length for minimum amount threads to screw in..That was after I put the proper angle of deflection. You can check out my web site. neilsplane.com Im building a lancair esp now...Neil ________________________________ Message 3 _____________________________________ Time: 09:15:31 AM PST US From: jc@INFONET.COM.BR Subject: Re: RV9-List: aileron push tubes --> RV9-List message posted by: jc@infonet.com.br Ive cutted them by Vans manual with any problems. To centralize the sticks Ive got some difficult. Some trials and errors using an plumb bob in both sticks. One hour job. To install the washers between the sticks and bell crank it is etter to buy washer tool at Avery. PU-JCI RV-9A Flying 125 hs JC - Aracaju - Brasil websites.expercraft.com/jcmm ________________________________ Message 4 _____________________________________ Time: 10:31:41 AM PST US From: " Peter Laurence" Subject: Re: RV9-List: aileron push tubes --> RV9-List message posted by: " Peter Laurence" Thanks Neil I'm from Tampsa. Where are you located/ Peter (A fuse ----- Original Message ----- From: Sent: Monday, May 08, 2006 11:33 AM Subject: Re: RV9-List: aileron push tubes > --> RV9-List message posted by: Neilekins@aol.com > > I cut them as per plans. I would add 1/4 inch to them. I had just enough > length for minimum amount threads to screw in..That was after I put the > proper > angle of deflection. You can check out my web site. neilsplane.com > Im > building a lancair esp now...Neil > > > ________________________________ Message 5 _____________________________________ Time: 08:06:25 PM PST US Subject: RV9-List: [ Richard Dudley ] : New Email List Photo Share Available! From: Email List Photo Shares --> RV9-List message posted by: Email List Photo Shares A new Email List Photo Share is available: Poster: Richard Dudley Lists: AeroElectric-List,RV3-List,RV4-List,RV6-List,RV7-List,RV8-List,RV9-List,RV10-List,RV-List Subject: Groundpower jack http://www.matronics.com/photoshare/rhdudley1@bellsouth.net.05.08.2006/index.html ---------------------------------------------------------- o Main Photo Share Index http://www.matronics.com/photoshare o Submitting a Photo Share If you wish to submit a Photo Share of your own, please include the following information along with your email message and files: 1) Email List or Lists that they are related to: 2) Your Full Name: 3) Your Email Address: 4) One line Subject description: 5) Multi-line, multi-paragraph description of topic: 6) One-line Description of each photo or file: Email the information above and your files and photos to: pictures@matronics.com ----------------------------------------------------------