RV9-List Digest Archive

Wed 10/18/06


Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 07:36 AM - Re: Wing skin oil-canning (Noel & Yoshie Simmons)
     2. 06:03 PM - Quick Build Packing Crate (John Oliveira)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:36:26 AM PST US
    From: "Noel & Yoshie Simmons" <noel@blueskyaviation.net>
    Subject: Wing skin oil-canning
    It's a real shocker to see that after completing a wing. I had it on an RV-10 I built. After flying I was able to overlook it some what and enjoy the ride. Noel RV-9A (for sale) _____ From: owner-rv9-list-server@matronics.com [mailto:owner-rv9-list-server@matronics.com] On Behalf Of Doug Fischer Sent: Tuesday, October 17, 2006 9:22 PM Subject: RV9-List: Wing skin oil-canning I just finished riveting on the top LH wing skins and I noticed one of the "squares" was indented and would "oil can" when pushed from the inside. The square is bounded by two ribs (the fourth and fifth from the tip), the forward spar, and the "J"stringer. It is the fourth bay inboard from the tip (RV-9). All other skin "squares" are tight/neutral. Any ideas (other than drilling out every rivet in the skin) to address this issue? I was thinking of drilling out the rivets around the square to allow the skin to average out between three squares and re-rivet. Just wanted to see if anyone else has run into this problem and worked out a solution. Other than this the skin is perfect (well, pretty good at least). Thanks in advance for the help! Doug Fischer Jenison, MI RV-9A Wings do not archive


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:03:58 PM PST US
    From: John Oliveira <oliveira@frontiernet.net>
    Subject: Quick Build Packing Crate
    --> RV9-List message posted by: John Oliveira <oliveira@frontiernet.net> I may need to ship my kit and I am looking for a packing crate for an RV7 or RV9 quick build kit. Mine is done past the stage of quick build but would probably fit in the crates. Is there anyone in Western NY, PA that has a quick build crate available or is scheduled to receive a quick build kit in the near future? Let me know John Oliveira 90054 - been working on it a while




    Other Matronics Email List Services

  • Post A New Message
  •   rv9-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/RV9-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/rv9-list
  • Browse RV9-List Digests
  •   http://www.matronics.com/digest/rv9-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --