Today's Message Index:
----------------------
1. 11:06 AM - Static Line Route (Bob Perkinson)
2. 01:46 PM - Re: Static Line Route (Wayne)
3. 02:33 PM - Re: Static Line Route (Chenoweth)
4. 03:25 PM - Re: Static Line Route (Chenoweth)
5. 03:47 PM - Re: Static Line Route (Bob Perkinson)
6. 05:37 PM - Re: Static Line Route (Maurice B.)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Static Line Route |
Group,
Where exactly did you rout the static line through bulkhead F5 (seat back bulkhead)?
I am at the point or running the static line and have it up under the longeron,
the way I see it the 7/16" hole needed to run the line would need to
be placed some where well below the rivet group holding the F5 doubler, putting
a 2" water trap in the line. Does this sag even matter? If the hole is drilled
high on F5 it looks like the edge distance on the rivets would be violated.
If any one has photos of this area, that would be nice.
Bob Perkinson
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=223173#223173
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Static Line Route |
An RVator from about two years ago has a picture.
----- Original Message -----
From: "Bob Perkinson" <bobperk90658@bellsouth.net>
Sent: Tuesday, January 06, 2009 2:05 PM
Subject: RV9-List: Static Line Route
> <bobperk90658@bellsouth.net>
>
> Group,
> Where exactly did you rout the static line through bulkhead F5 (seat back
> bulkhead)? I am at the point or running the static line and have it up
> under the longeron, the way I see it the 7/16" hole needed to run the line
> would need to be placed some where well below the rivet group holding the
> F5 doubler, putting a 2" water trap in the line. Does this sag even
> matter? If the hole is drilled high on F5 it looks like the edge distance
> on the rivets would be violated.
> If any one has photos of this area, that would be nice.
> Bob Perkinson
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=223173#223173
>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Static Line Route |
Thanks - I was just about to ask you for her name again. Looks like the
project is going forward.
----- Original Message -----
From: "Wayne" <wowens@darientel.net>
Sent: Tuesday, January 06, 2009 4:42 PM
Subject: Re: RV9-List: Static Line Route
>
> An RVator from about two years ago has a picture.
> ----- Original Message -----
> From: "Bob Perkinson" <bobperk90658@bellsouth.net>
> To: <rv9-list@matronics.com>
> Sent: Tuesday, January 06, 2009 2:05 PM
> Subject: RV9-List: Static Line Route
>
>
>> <bobperk90658@bellsouth.net>
>>
>> Group,
>> Where exactly did you rout the static line through bulkhead F5 (seat back
>> bulkhead)? I am at the point or running the static line and have it up
>> under the longeron, the way I see it the 7/16" hole needed to run the
>> line
>> would need to be placed some where well below the rivet group holding the
>> F5 doubler, putting a 2" water trap in the line. Does this sag even
>> matter? If the hole is drilled high on F5 it looks like the edge
>> distance
>> on the rivets would be violated.
>> If any one has photos of this area, that would be nice.
>> Bob Perkinson
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=223173#223173
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
--------------------------------------------------------------------------------
Checked by AVG - http://www.avg.com
2:34 PM
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Static Line Route |
Sorry folks - slip of the "response" finger with the "project is going
forward" thing.
However, Bob, regarding your static line routing. As mentioned, the RVator
has an article but as I recall there were some labeling errors in the
captions or such. I did mine the way the article suggested and am still
pretty much wide open in the fuselage department so I can send pictures if
you want.
Bill
----- Original Message -----
From: "Chenoweth" <chenoweth@gwi.net>
Sent: Tuesday, January 06, 2009 5:33 PM
Subject: Re: RV9-List: Static Line Route
>
> Thanks - I was just about to ask you for her name again. Looks like the
> project is going forward.
> ----- Original Message -----
> From: "Wayne" <wowens@darientel.net>
> To: <rv9-list@matronics.com>
> Sent: Tuesday, January 06, 2009 4:42 PM
> Subject: Re: RV9-List: Static Line Route
>
>
>>
>> An RVator from about two years ago has a picture.
>> ----- Original Message -----
>> From: "Bob Perkinson" <bobperk90658@bellsouth.net>
>> To: <rv9-list@matronics.com>
>> Sent: Tuesday, January 06, 2009 2:05 PM
>> Subject: RV9-List: Static Line Route
>>
>>
>>> <bobperk90658@bellsouth.net>
>>>
>>> Group,
>>> Where exactly did you rout the static line through bulkhead F5 (seat
>>> back
>>> bulkhead)? I am at the point or running the static line and have it up
>>> under the longeron, the way I see it the 7/16" hole needed to run the
>>> line
>>> would need to be placed some where well below the rivet group holding
>>> the
>>> F5 doubler, putting a 2" water trap in the line. Does this sag even
>>> matter? If the hole is drilled high on F5 it looks like the edge
>>> distance
>>> on the rivets would be violated.
>>> If any one has photos of this area, that would be nice.
>>> Bob Perkinson
>>>
>>>
>>>
>>>
>>> Read this topic online here:
>>>
>>> http://forums.matronics.com/viewtopic.php?p=223173#223173
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>>
>
>
> --------------------------------------------------------------------------------
>
>
> Checked by AVG - http://www.avg.com
> 2:34 PM
>
>
--------------------------------------------------------------------------------
Checked by AVG - http://www.avg.com
2:34 PM
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Static Line Route |
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Static Line Route |
I have an rv6a=2C but I run mine=2C right under the longeron=2C all the way
=2C then along horizontally to the insturment pannel..
I use plastic=2C stand offs=2C glue with proseal=2C=2C alongl the way to h
old plastic line=2C with tie wraps.. Acutally you do not need that..
Robert
> From: wowens@darientel.net> To: rv9-list@matronics.com> Subject: Re: RV9-
List: Static Line Route> Date: Tue=2C 6 Jan 2009 16:42:48 -0500> > --> RV9-
List message posted by: "Wayne" <wowens@darientel.net>> > An RVator from ab
out two years ago has a picture.> ----- Original Message ----- > From: "Bob
Perkinson" <bobperk90658@bellsouth.net>> To: <rv9-list@matronics.com>> Sen
t: Tuesday=2C January 06=2C 2009 2:05 PM> Subject: RV9-List: Static Line Ro
8@bellsouth.net>> >> > Group=2C> > Where exactly did you rout the static li
ne through bulkhead F5 (seat back > > bulkhead)? I am at the point or runni
ng the static line and have it up > > under the longeron=2C the way I see i
t the 7/16" hole needed to run the line > > would need to be placed some wh
ere well below the rivet group holding the > > F5 doubler=2C putting a 2" w
ater trap in the line. Does this sag even > > matter? If the hole is drille
d high on F5 it looks like the edge distance > > on the rivets would be vio
lated.> > If any one has photos of this area=2C that would be nice.> > Bob
Perkinson> >> >> >> >> > Read this topic online here:> >> > http://forums.m
atronics.com/viewtopic.php?p=223173#223173> >> >> >> >> >> >> >> >> >> >>
================> > >
_________________________________________________________________
It=92s the same Hotmail=AE. If by =93same=94 you mean up to 70% faster.
http://windowslive.com/online/hotmail?ocid=TXT_TAGLM_WL_hotmail_acq_broad
1_122008
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|