---------------------------------------------------------- RV9-List Digest Archive --- Total Messages Posted Tue 01/06/09: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 11:06 AM - Static Line Route (Bob Perkinson) 2. 01:46 PM - Re: Static Line Route (Wayne) 3. 02:33 PM - Re: Static Line Route (Chenoweth) 4. 03:25 PM - Re: Static Line Route (Chenoweth) 5. 03:47 PM - Re: Static Line Route (Bob Perkinson) 6. 05:37 PM - Re: Static Line Route (Maurice B.) ________________________________ Message 1 _____________________________________ Time: 11:06:45 AM PST US Subject: RV9-List: Static Line Route From: "Bob Perkinson" Group, Where exactly did you rout the static line through bulkhead F5 (seat back bulkhead)? I am at the point or running the static line and have it up under the longeron, the way I see it the 7/16" hole needed to run the line would need to be placed some where well below the rivet group holding the F5 doubler, putting a 2" water trap in the line. Does this sag even matter? If the hole is drilled high on F5 it looks like the edge distance on the rivets would be violated. If any one has photos of this area, that would be nice. Bob Perkinson Read this topic online here: http://forums.matronics.com/viewtopic.php?p=223173#223173 ________________________________ Message 2 _____________________________________ Time: 01:46:19 PM PST US From: "Wayne" Subject: Re: RV9-List: Static Line Route An RVator from about two years ago has a picture. ----- Original Message ----- From: "Bob Perkinson" Sent: Tuesday, January 06, 2009 2:05 PM Subject: RV9-List: Static Line Route > > > Group, > Where exactly did you rout the static line through bulkhead F5 (seat back > bulkhead)? I am at the point or running the static line and have it up > under the longeron, the way I see it the 7/16" hole needed to run the line > would need to be placed some where well below the rivet group holding the > F5 doubler, putting a 2" water trap in the line. Does this sag even > matter? If the hole is drilled high on F5 it looks like the edge distance > on the rivets would be violated. > If any one has photos of this area, that would be nice. > Bob Perkinson > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=223173#223173 > > > ________________________________ Message 3 _____________________________________ Time: 02:33:46 PM PST US From: "Chenoweth" Subject: Re: RV9-List: Static Line Route Thanks - I was just about to ask you for her name again. Looks like the project is going forward. ----- Original Message ----- From: "Wayne" Sent: Tuesday, January 06, 2009 4:42 PM Subject: Re: RV9-List: Static Line Route > > An RVator from about two years ago has a picture. > ----- Original Message ----- > From: "Bob Perkinson" > To: > Sent: Tuesday, January 06, 2009 2:05 PM > Subject: RV9-List: Static Line Route > > >> >> >> Group, >> Where exactly did you rout the static line through bulkhead F5 (seat back >> bulkhead)? I am at the point or running the static line and have it up >> under the longeron, the way I see it the 7/16" hole needed to run the >> line >> would need to be placed some where well below the rivet group holding the >> F5 doubler, putting a 2" water trap in the line. Does this sag even >> matter? If the hole is drilled high on F5 it looks like the edge >> distance >> on the rivets would be violated. >> If any one has photos of this area, that would be nice. >> Bob Perkinson >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=223173#223173 >> >> >> >> >> >> >> >> >> >> >> > > -------------------------------------------------------------------------------- Checked by AVG - http://www.avg.com 2:34 PM ________________________________ Message 4 _____________________________________ Time: 03:25:55 PM PST US From: "Chenoweth" Subject: Re: RV9-List: Static Line Route Sorry folks - slip of the "response" finger with the "project is going forward" thing. However, Bob, regarding your static line routing. As mentioned, the RVator has an article but as I recall there were some labeling errors in the captions or such. I did mine the way the article suggested and am still pretty much wide open in the fuselage department so I can send pictures if you want. Bill ----- Original Message ----- From: "Chenoweth" Sent: Tuesday, January 06, 2009 5:33 PM Subject: Re: RV9-List: Static Line Route > > Thanks - I was just about to ask you for her name again. Looks like the > project is going forward. > ----- Original Message ----- > From: "Wayne" > To: > Sent: Tuesday, January 06, 2009 4:42 PM > Subject: Re: RV9-List: Static Line Route > > >> >> An RVator from about two years ago has a picture. >> ----- Original Message ----- >> From: "Bob Perkinson" >> To: >> Sent: Tuesday, January 06, 2009 2:05 PM >> Subject: RV9-List: Static Line Route >> >> >>> >>> >>> Group, >>> Where exactly did you rout the static line through bulkhead F5 (seat >>> back >>> bulkhead)? I am at the point or running the static line and have it up >>> under the longeron, the way I see it the 7/16" hole needed to run the >>> line >>> would need to be placed some where well below the rivet group holding >>> the >>> F5 doubler, putting a 2" water trap in the line. Does this sag even >>> matter? If the hole is drilled high on F5 it looks like the edge >>> distance >>> on the rivets would be violated. >>> If any one has photos of this area, that would be nice. >>> Bob Perkinson >>> >>> >>> >>> >>> Read this topic online here: >>> >>> http://forums.matronics.com/viewtopic.php?p=223173#223173 >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >> >> >> >> >> > > > -------------------------------------------------------------------------------- > > > Checked by AVG - http://www.avg.com > 2:34 PM > > -------------------------------------------------------------------------------- Checked by AVG - http://www.avg.com 2:34 PM ________________________________ Message 5 _____________________________________ Time: 03:47:45 PM PST US From: "Bob Perkinson" Subject: Re: RV9-List: Static Line Route ________________________________ Message 6 _____________________________________ Time: 05:37:11 PM PST US From: "Maurice B." Subject: RE: RV9-List: Static Line Route I have an rv6a=2C but I run mine=2C right under the longeron=2C all the way =2C then along horizontally to the insturment pannel.. I use plastic=2C stand offs=2C glue with proseal=2C=2C alongl the way to h old plastic line=2C with tie wraps.. Acutally you do not need that.. Robert > From: wowens@darientel.net> To: rv9-list@matronics.com> Subject: Re: RV9- List: Static Line Route> Date: Tue=2C 6 Jan 2009 16:42:48 -0500> > --> RV9- List message posted by: "Wayne" > > An RVator from ab out two years ago has a picture.> ----- Original Message ----- > From: "Bob Perkinson" > To: > Sen t: Tuesday=2C January 06=2C 2009 2:05 PM> Subject: RV9-List: Static Line Ro 8@bellsouth.net>> >> > Group=2C> > Where exactly did you rout the static li ne through bulkhead F5 (seat back > > bulkhead)? I am at the point or runni ng the static line and have it up > > under the longeron=2C the way I see i t the 7/16" hole needed to run the line > > would need to be placed some wh ere well below the rivet group holding the > > F5 doubler=2C putting a 2" w ater trap in the line. Does this sag even > > matter? If the hole is drille d high on F5 it looks like the edge distance > > on the rivets would be vio lated.> > If any one has photos of this area=2C that would be nice.> > Bob Perkinson> >> >> >> >> > Read this topic online here:> >> > http://forums.m atronics.com/viewtopic.php?p=223173#223173> >> >> >> >> >> >> >> >> >> >> ================> > > _________________________________________________________________ It=92s the same Hotmail=AE. If by =93same=94 you mean up to 70% faster. http://windowslive.com/online/hotmail?ocid=TXT_TAGLM_WL_hotmail_acq_broad 1_122008 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv9-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV9-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv9-list Browse Digests http://www.matronics.com/digest/rv9-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.