RVCanada-List Digest Archive

Sat 02/05/05


Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 05:09 PM - RV6-a upper gear leg intersection Fairings attachment (Jim Jewell)
     2. 10:50 PM - Re: RV6-a upper gear leg intersection Fairings (GMC)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:09:00 PM PST US
    From: "Jim Jewell" <jjewell@telus.net>
    Subject: RV6-a upper gear leg intersection Fairings attachment
    --> RVCanada-List message posted by: "Jim Jewell" <jjewell@telus.net> My RV6-A is on the wheels in my garage. Bob's http://www.fairings-etc.com wheel pant intersection fairings are fitted and laminated onto the Van's wheel pants. Bob's parts dropped in place and it took me quite a lot of effort to fit, laminate and finish to match the quality of his craftsmanship. Thanks Bob! Now I am looking for some ideas and hopefully some pictures as to attachment of the upper leg intersection fairing to the fuselage. I am looking for suggestions re- attachment points, hardware suggestions: Rivnuts Platenuts, Tinnermans, Springs and mounting point locations etc. I have been mulling this over for a while and have yet to settle them in place. If you have pictures I'd sure like to see them. Thanks in advance, Jim in Kelowna


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:50:39 PM PST US
    From: GMC <gmcnutt@shaw.ca> attachment
    Subject: RV6-a upper gear leg intersection Fairings
    attachment --> RVCanada-List message posted by: GMC <gmcnutt@shaw.ca> attachment Hi Jim I used plate nuts, no helper so pop riveted to inside of fuselage floor. Sorry no pictures. I also put the end of the rubber wing root fairing trim strip under the gear leg fairing so it would not work loose. Hope to see you flying to the Langley RV fly-in - June. George in Langley -------------------------- Now I am looking for some ideas and hopefully some pictures as to attachment of the upper leg intersection fairing to the fuselage. I am looking for suggestions re- attachment points, hardware suggestions: Rivnuts Platenuts, Tinnermans, Springs and mounting point locations etc. I have been mulling this over for a while and have yet to settle them in place. If you have pictures I'd sure like to see them. Thanks in advance, Jim in Kelowna




    Other Matronics Email List Services

  • Post A New Message
  •   rvcanada-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/RVCanada-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/rvcanada-list
  • Browse RVCanada-List Digests
  •   http://www.matronics.com/digest/rvcanada-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --