Today's Message Index:
----------------------
1. 08:38 AM - MT Prop Gov (Breece Nesbitt)
2. 01:53 PM - Re: MT Prop Gov (Radomir Zaric)
3. 06:42 PM - Re: MT Prop Gov (Breece Nesbitt)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I am installing an MTP-860-4 prop governor on-my IO-360 and have run into
a problem.-The AN3-11A bolt that attaches the rod end bearing to the gov
ernor arm is so long that it will not-line up with the hole in the arm.
- Has anyone else run into this and could give me some advice?- I don't
want to loosen the arm from the shaft unless I have to.=0A=0ABreece Nesbit
t=0ARV-8
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Some use(d) -10A bolt, so they can slide it into the hole..
From: owner-rvsoutheast-list-server@matronics.com
[mailto:owner-rvsoutheast-list-server@matronics.com] On Behalf Of Breece
Nesbitt
Sent: Monday, May 18, 2009 11:37 AM
Subject: RVSouthEast-List: MT Prop Gov
I am installing an MTP-860-4 prop governor on my IO-360 and have run into a
problem. The AN3-11A bolt that attaches the rod end bearing to the governor
arm is so long that it will not line up with the hole in the arm. Has
anyone else run into this and could give me some advice? I don't want to
loosen the arm from the shaft unless I have to.
Breece Nesbitt
RV-8
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thanks for getting back to me on this.-I called Van's and talked with Tom
.- He said that the direction of the bolt was not critical, and that it c
ould be put in from the other side.-That's what I did, and it worked.-
=0A=0ABreece=0A=0A=0A=0A=0A________________________________=0AFrom: Radomir
Zaric <vitez@carolina.rr.com>=0ATo: rvsoutheast-list@matronics.com=0ASent:
Monday, May 18, 2009 4:49:41 PM=0ASubject: RE: RVSouthEast-List: MT Prop G
ov=0A=0A=0ASome use(d) -10A bolt, so they can slide it into the hole..-
- =0A-=0A-=0A-=0AFrom:owner-rvsoutheast-list-server@matronics.com [
mailto:owner-rvsoutheast-list-server@matronics.com] On Behalf Of Breece Nes
bitt=0ASent: Monday, May 18, 2009 11:37 AM=0ATo: rvsoutheast-list@matronics
.com=0ASubject: RVSouthEast-List: MT Prop Gov=0A-=0AI am installing an MT
P-860-4 prop governor on-my IO-360 and have run into a problem.-The AN3
-11A bolt that attaches the rod end bearing to the governor arm is so long
that it will not-line up with the hole in the arm.- Has anyone else run
into this and could give me some advice?- I don't want to loosen the arm
from the shaft unless I have to.=0A-=0ABreece Nesbitt=0ARV-8=0A -=0A
-=0Ahttp://www.matronics.com/Navigator?RVSouthEast-List=0Ahttp://forums.m
===============
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|