Today's Message Index:
----------------------
1. 04:13 AM - Re: building floats (jnbolding1)
2. 06:31 PM - Re: building floats (Malcolmbru@aol.com)
3. 07:04 PM - Re: building floats (John A. Nielsen)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: building floats |
--> Seaplane-List message posted by: "jnbolding1" <jnbolding1@mail.ev1.net>
>I am starting on the second float But havn't finished the first I need
>a keel what kind of material to use? most of 2ed float is cut bent
>ready to install it should go togither fast I used a hole tube of 5200
and
>1000 rivites and still have the buttom to install mal
Mal, The part shown on the drawings is a special extrusion available only from
Zenith and they turned over all their float stuff to Skyshops and Czech Aircraft
Works, they haven't been anxious to sell just keel strips when I asked but
if we ordered enough for several sets maybe they would ,I'll ask.
Failing that we are left with bending up something from 090 or .125 strip. John
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: building floats |
--> Seaplane-List message posted by: Malcolmbru@aol.com
090 or 125 is that 1/6 th inch? I can get 2+21/6 angel at lowes than ripe
it at the corner but it is only 8 ft long and I need 8ft4 in then it wont
land on a bulk head or stifiner so I need another 2 ft on the rear buttom
I
need to know what type of matereal to get bending the cromoli of 050
for the mounting at bulkhear 3 and 5 is not a problem do I also need to build
2 more stifiners to fasten the float to the plain?or is it only fastened at
the bulkheds? mal
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: building floats |
--> Seaplane-List message posted by: "John A. Nielsen" <john@nielsenford.com>
I can not take it any more!!. mal, I may be the only one you drive away
from this forum, but what if I am wrong??? How many opportunities for
experienced educated assistance might you be blowing off with this
absolutely atrocious spelling and grammar? Good bye and good luck!
John Nielsen
Malcolmbru@aol.com wrote:
> --> Seaplane-List message posted by: Malcolmbru@aol.com
>
> 090 or 125 is that 1/6 th inch? I can get 2+21/6 angel at lowes than ripe
> it at the corner but it is only 8 ft long and I need 8ft4 in then it wont
> land on a bulk head or stifiner so I need another 2 ft on the rear buttom
I
> need to know what type of matereal to get bending the cromoli of 050
> for the mounting at bulkhear 3 and 5 is not a problem do I also need to build
> 2 more stifiners to fasten the float to the plain?or is it only fastened at
> the bulkheds? mal
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|