Today's Message Index:
----------------------
1. 06:37 AM - Re: Prop Balance (Bill Morelli)
2. 08:19 AM - Re: Motor Mounts Again (HINDE,FRANK (HP-Corvallis,ex1))
3. 08:21 AM - Re: Motor Mounts Again (HINDE,FRANK (HP-Corvallis,ex1))
4. 07:22 PM - Re: Prop Balance (RLucka@aol.com)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Stratus-List message posted by: "Bill Morelli" <billvt@together.net>
Dick,
What exactly did he do to blance the prop?
Thanks,
Bill
> --> Stratus-List message posted by: RLucka@aol.com
>
> Hi Stratus Guys
>
> I just wanted to relate an experience I had in getting my Warp Drive
> dynamically balanced.
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Motor Mounts Again |
--> Stratus-List message posted by: "HINDE,FRANK (HP-Corvallis,ex1)" <frank.hinde@hp.com>
As long as the valve guide issue is resolved they are.
Frank
-----Original Message-----
From: owner-stratus-list-server@matronics.com
[mailto:owner-stratus-list-server@matronics.com] On Behalf Of The Meiste's
Subject: Re: Stratus-List: Motor Mounts Again
--> Stratus-List message posted by: "The Meiste's" <meiste@essex1.com>
> I just flew off my 40 hours today, feels good. A 2.5 hour flight,
> then
ate,
> refueled and 3 more hours. No problems at all, these really are great
> engines
Hi Gary,
Congrats on hitting the 40 hour mark! How's your temps now? I'll try sending
you a few photo's of my repair tomorrow.
Kelly
Do not archive
advertising on the Matronics Forums.
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Motor Mounts Again |
--> Stratus-List message posted by: "HINDE,FRANK (HP-Corvallis,ex1)" <frank.hinde@hp.com>
It takes five minutes to re torque the whole head...BUT I have replaced the
mount without doing so as well with no problems.
Frank
-----Original Message-----
From: owner-stratus-list-server@matronics.com
[mailto:owner-stratus-list-server@matronics.com] On Behalf Of The Meiste's
Subject: Re: Stratus-List: Motor Mounts Again
--> Stratus-List message posted by: "The Meiste's" <meiste@essex1.com>
One question about reinstalling the motor mount.
My book shows the two nuts that hold the motor mount onto the engine must be
torqued down to 47 ft/lbs. Must the entire head now be retorqued, or can I
just retorque the two nuts back to 47 ft/lbs?
Thanks for any advice.
Kelly
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Prop Balance |
--> Stratus-List message posted by: RLucka@aol.com
In a message dated 4/19/2004 9:37:44 AM Eastern Standard Time,
billvt@together.net writes:
What exactly did he do to blance the prop?
Bill
The A&P used a dynamic balancer (or whatever it's called) with sensors
attached to the reduction unit and the cowl. The second sensor watched for a strip
of metal attached to one of the prop blades. I had to run the engine (with
the prop on of course) at my cruise speed (4000 rpm) a few times while his
little computer figures out where to add weights and how much weight. After 3
runs, he added two bolts/ washers/ & nuts to the spinner mounting piece (the piece
that is attached to the prop hub and contains flanges for the spinner to be
attached to).
I don't remember what his tool is called, but it does work.
Hope this helps.
Dick
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|