Today's Message Index:
----------------------
1. 12:07 PM - Timing Engine (Andrew SanClemente)
2. 12:09 PM - Re: Timing Engine (Hinde, Frank George (Corvallis))
3. 12:14 PM - Disregard Previous Message about Timing (Andrew SanClemente)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Stratus-List message posted by: Andrew SanClemente <duck@townisp.com>
Im currently trying to do the timing on my EA-81 and am having some
problems. I have my gun set to 32 degrees and am revving to 4,000 but
I cannot pickup the mark on the pulley in the flash. When I adjust
the distributor I can hear the range where the engine runs nice so I
should be able to see the mark on the pulley somewhere in the flash
range but no luck. I tried extending the mark across the whole pulley
to make it easier to see. Anyone have any suggestions?
Thanks
Andy
Im currently trying to do the timing on my EA-81 and am having some problems.
I have my gun set to 32 degrees and am revving to 4,000 but I cannot pickup the
mark on the pulley in the flash. When I adjust the distributor I can hear the
range where the engine runs nice so I should be able to see the mark on the
pulley somewhere in the flash range but no luck. I tried extending the mark across
the whole pulley to make it easier to see. Anyone have any suggestions?
Thanks
Andy
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Stratus-List message posted by: "Hinde, Frank George (Corvallis)" <frank.hinde@hp.com>
Are you sure you have your timing light hooked to #1 cylinder?
Other than that try doing it just as the sun goes down.
Frank
-----Original Message-----
From: owner-stratus-list-server@matronics.com
[mailto:owner-stratus-list-server@matronics.com] On Behalf Of Andrew
SanClemente
Subject: Stratus-List: Timing Engine
--> Stratus-List message posted by: Andrew SanClemente
--> <duck@townisp.com>
Im currently trying to do the timing on my EA-81 and am having some
problems. I have my gun set to 32 degrees and am revving to 4,000 but
I cannot pickup the mark on the pulley in the flash. When I adjust
the distributor I can hear the range where the engine runs nice so I
should be able to see the mark on the pulley somewhere in the flash
range but no luck. I tried extending the mark across the whole pulley
to make it easier to see. Anyone have any suggestions?
Thanks
Andy
Im currently trying to do the timing on my EA-81 and am having some
problems. I have my gun set to 32 degrees and am revving to 4,000 but I
cannot pickup the mark on the pulley in the flash. When I adjust the
distributor I can hear the range where the engine runs nice so I should
be able to see the mark on the pulley somewhere in the flash range but
no luck. I tried extending the mark across the whole pulley to make it
easier to see. Anyone have any suggestions? Thanks
Andy
==
direct advertising on the Matronics Forums.
==
==
==
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Disregard Previous Message about Timing |
--> Stratus-List message posted by: Andrew SanClemente <duck@townisp.com>
Ignore my previous email, "pilot error" on the gun, timing set
perfect,
Thanks
Andy
DO NOT ARCHIVE
Ignore my previous email, pilot error on the gun, timing set perfect,
Thanks
Andy
DO NOT ARCHIVE
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|