----------------------------------------------------------
                           Stratus-List Digest Archive
                                      ---
                     Total Messages Posted Mon 09/03/07: 2
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 06:47 PM - Replacing Bearings in a Stratus PSRU  (Falcon)
     2. 07:44 PM - Re: Replacing Bearings in a Stratus PSRU  (Andy Fultz)
 
 
 
________________________________  Message 1  _____________________________________


Time: 06:47:30 PM PST US
Subject: Stratus-List: Replacing Bearings in a Stratus PSRU
From: "Falcon" <crx@ubbdev.com>


Stratus EA-81 conversion,  ca. 1999.

I need to replace my PSRU bearings -- these are the two 6207-2RS bearings in the
large hub.  To get to them, I think I need to pull the spindle, by loosening
the jam nut on the back of the PSRU.  Now, the jam nut is a spanner type, with
four rectangular notches, cut into the perimeter of the nut at 90 degree increments.

Where do I find a wrench that will handle this?

Please note I've also asked the Zenith list, as this is hanging off the nose of
my CH-601 HDS.


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=132589#132589


________________________________  Message 2  _____________________________________


Time: 07:44:25 PM PST US
From: "Andy Fultz" <andynfultz@bellsouth.net>
Subject: RE: Stratus-List: Replacing Bearings in a Stratus PSRU


When I ordered my Stratus, they sent the wrenches to work on it (the
reduction) when they shipped my engine.  You may want to contact them.

Andy Fultz

-----Original Message-----
From: owner-stratus-list-server@matronics.com
[mailto:owner-stratus-list-server@matronics.com]On Behalf Of Falcon
Sent: Monday, September 03, 2007 8:47 PM
Subject: Stratus-List: Replacing Bearings in a Stratus PSRU



Stratus EA-81 conversion,  ca. 1999.

I need to replace my PSRU bearings -- these are the two 6207-2RS bearings in
the large hub.  To get to them, I think I need to pull the spindle, by
loosening the jam nut on the back of the PSRU.  Now, the jam nut is a
spanner type, with four rectangular notches, cut into the perimeter of the
nut at 90 degree increments.

Where do I find a wrench that will handle this?

Please note I've also asked the Zenith list, as this is hanging off the nose
of my CH-601 HDS.


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=132589#132589


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               stratus-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Stratus-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/stratus-list
Browse Digests                   http://www.matronics.com/digest/stratus-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.