Stratus-List Digest Archive

Sun 09/11/11


Total Messages Posted: 5



Today's Message Index:
----------------------
 
     1. 08:12 AM - Flight Test for a Remote Oil Filter Kit on the Stratus Subaru (Larry McFarland)
     2. 09:01 AM - Re: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru (Gary Krysztopik)
     3. 09:32 AM - Re: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru (Larry McFarland)
     4. 11:22 AM - Re: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru (Gary Krysztopik)
     5. 12:22 PM - Re: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru (Larry McFarland)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:12:34 AM PST US
    From: "Larry McFarland" <larry@macsmachine.com>
    Subject: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru
    Hi guys, Sept 10 After a Hy-Vee lunch with the guys, I went to the hangar and did a thorough preflight, did take a full 5 quarts to top oil off before startup. The Subaru fired up immediately and I taxied out. Oil temps began at 60 p.s.i. and when warmed went down to 45 p.s.i. Tower cleared me for 10. The lift off was trim-adjusted with no perceptible feel for the weight change up front. I flew south of the control zone to the designated "practice area. Oil temps at 3000 feet reached 228 degrees at 4300 rpm and I progressively brought up the power in 100 rpm increments every 8 minutes or so. CHTs stayed 190 to 200 degrees, EGTs 1380, Coolant 200 and when rpms reached 5100 and airspeed at 128 mph, oil temps never went over 233 degrees. All other temps stayed well in the green. The remote oil filter kit resolved the max temp issues. I stayed on an east west track until I was satisfied that the engine was happy within its full range of operation and then headed back to Moline. Descending at 125 into the pattern was easy, the landing was smooth and I taxied back to the south tees with 175 hours on the engine. The cowl was unbuttoned, the engine was drip-free and oil hoses stayed where they'd been clamped. Pictures are added <http://www.macsmachine.com/html/subaruengine.htm> to the bottom of my engine page that shows the components and installation in greater detail. Very satisfied with this modification! Data was entered into the logs. Larry McFarland 601HDS at www.macsmachine.com


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:01:59 AM PST US
    From: Gary Krysztopik <gkrysztopik@satx.rr.com>
    Subject: Re: Flight Test for a Remote Oil Filter Kit on the Stratus
    Subaru Thanks for posting Larry. What would you say the difference is in oil temp - what would the oil temp have been below without the remote filter? Gary Krysztopik ZWheelz, LLC - www.ZWheelz.com Alamo City Electric Auto Association - www.aceaa.org blog - http://voices.mysanantonio.com/drive_electric_san_antonio/ San Antonio, TX On 9/11/2011 10:09 AM, Larry McFarland wrote: > > Hi guys, > > *Sept 10* After a Hy-Vee lunch with the guys, I went to the hangar and > did a thorough preflight, did take a full 5 quarts to top oil off > before startup. The Subaru fired up immediately and I taxied out. Oil > temps began at 60 p.s.i. and when warmed went down to 45 p.s.i. Tower > cleared me for 10. The lift off was trim-adjusted with no perceptible > feel for the weight change up front. I flew south of the control zone > to the designated "practice area. Oil temps at 3000 feet reached 228 > degrees at 4300 rpm and I progressively brought up the power in 100 > rpm increments every 8 minutes or so. CHTs stayed 190 to 200 degrees, > EGTs 1380, Coolant 200 and when rpms reached 5100 and airspeed at 128 > mph, oil temps never went over 233 degrees. All other temps stayed > well in the green. The remote oil filter kit resolved the max temp > issues. I stayed on an east west track until I was satisfied that the > engine was happy within its full range of operation and then headed > back to Moline. Descending at 125 into the pattern was easy, the > landing was smooth and I taxied back to the south tees with 175 hours > on the engine. The cowl was unbuttoned, the engine was drip-free and > oil hoses stayed where they'd been clamped.Pictures are added > <http://www.macsmachine.com/html/subaruengine.htm> to the bottom of my > engine page that shows the components and installation in greater > detail. Very satisfied with this modification! Data was entered into > the logs. > > Larry McFarland 601HDS at www.macsmachine.com > > * > > > *


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:32:44 AM PST US
    From: "Larry McFarland" <larry@macsmachine.com>
    Subject: Flight Test for a Remote Oil Filter Kit on the Stratus
    Subaru Hi Gary, >From my journal, I'd earlier posted; Note: I often think an oil cooler might be a worthwhile addition. I had concern for oil temps that ran as high as 235 degrees F. The manual states 260 is the max oil temp permitted. Flying at 130 mph at 5200 rpm on a hot day of more than 90-degrees, engine oil will eventually reach 250 degrees (my warning set-point on the EIS) so I do back off to 4600 rpm and cruise at 115 to 120 mph. Oil temps will then stay near 235. Larry McFarland 601HDS at www.macsmachine.com From: owner-stratus-list-server@matronics.com [mailto:owner-stratus-list-server@matronics.com] On Behalf Of Gary Krysztopik Sent: Sunday, September 11, 2011 11:00 AM Subject: Re: Stratus-List: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru Thanks for posting Larry. What would you say the difference is in oil temp - what would the oil temp have been below without the remote filter? Gary Krysztopik ZWheelz, LLC - www.ZWheelz.com Alamo City Electric Auto Association - www.aceaa.org blog - http://voices.mysanantonio.com/drive_electric_san_antonio/ San Antonio, TX On 9/11/2011 10:09 AM, Larry McFarland wrote: Hi guys, Sept 10 After a Hy-Vee lunch with the guys, I went to the hangar and did a thorough preflight, did take a full 5 quarts to top oil off before startup. The Subaru fired up immediately and I taxied out. Oil temps began at 60 p.s.i. and when warmed went down to 45 p.s.i. Tower cleared me for 10. The lift off was trim-adjusted with no perceptible feel for the weight change up front. I flew south of the control zone to the designated "practice area. Oil temps at 3000 feet reached 228 degrees at 4300 rpm and I progressively brought up the power in 100 rpm increments every 8 minutes or so. CHTs stayed 190 to 200 degrees, EGTs 1380, Coolant 200 and when rpms reached 5100 and airspeed at 128 mph, oil temps never went over 233 degrees. All other temps stayed well in the green. The remote oil filter kit resolved the max temp issues. I stayed on an east west track until I was satisfied that the engine was happy within its full range of operation and then headed back to Moline. Descending at 125 into the pattern was easy, the landing was smooth and I taxied back to the south tees with 175 hours on the engine. The cowl was unbuttoned, the engine was drip-free and oil hoses stayed where they'd been clamped. Pictures are added <http://www.macsmachine.com/html/subaruengine.htm> to the bottom of my engine page that shows the components and installation in greater detail. Very satisfied with this modification! Data was entered into the logs. Larry McFarland 601HDS at www.macsmachine.com


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:22:29 AM PST US
    From: Gary Krysztopik <gkrysztopik@satx.rr.com>
    Subject: Re: Flight Test for a Remote Oil Filter Kit on the Stratus
    Subaru Was it also 90+ degrees? If so, you went from about 250 to 233 degrees at around 130 mph and 5200 rpm. That's much more significant than I would have guessed for just a remote filter. I like where you mounted it, perfect spot with plenty of room and great airflow. Nice work, thanks. Gary Krysztopik ZWheelz, LLC - www.ZWheelz.com Alamo City Electric Auto Association - www.aceaa.org blog - http://voices.mysanantonio.com/drive_electric_san_antonio/ San Antonio, TX On 9/11/2011 11:29 AM, Larry McFarland wrote: > > Hi Gary, > > From my journal, I'd earlier posted; > > Note: I often think an oil cooler might be a worthwhile addition. > I had concern for oil temps that ran as high as 235 degrees F. The > manual states 260 is the max oil temp permitted. Flying at 130 mph at > 5200 rpm on a hot day of more than 90-degrees, engine oil will > eventually reach 250 degrees (my warning set-point on the EIS) so I do > back off to 4600 rpm and cruise at 115 to 120 mph. Oil temps will then > stay near 235. > > Larry McFarland 601HDS at www.macsmachine.com > > *From:*owner-stratus-list-server@matronics.com > [mailto:owner-stratus-list-server@matronics.com] *On Behalf Of *Gary > Krysztopik > *Sent:* Sunday, September 11, 2011 11:00 AM > *To:* stratus-list@matronics.com > *Subject:* Re: Stratus-List: Flight Test for a Remote Oil Filter Kit > on the Stratus Subaru > > Thanks for posting Larry. What would you say the difference is in oil > temp - what would the oil temp have been below without the remote filter? > > Gary Krysztopik > ZWheelz, LLC -www.ZWheelz.com <http://www.ZWheelz.com> > Alamo City Electric Auto Association -www.aceaa.org <http://www.aceaa.org> > blog -http://voices.mysanantonio.com/drive_electric_san_antonio/ > San Antonio, TX > > > On 9/11/2011 10:09 AM, Larry McFarland wrote: > > Hi guys, > > *Sept 10* After a Hy-Vee lunch with the guys, I went to the hangar and > did a thorough preflight, did take a full 5 quarts to top oil off > before startup. The Subaru fired up immediately and I taxied out. Oil > temps began at 60 p.s.i. and when warmed went down to 45 p.s.i. Tower > cleared me for 10. The lift off was trim-adjusted with no perceptible > feel for the weight change up front. I flew south of the control zone > to the designated "practice area. Oil temps at 3000 feet reached 228 > degrees at 4300 rpm and I progressively brought up the power in 100 > rpm increments every 8 minutes or so. CHTs stayed 190 to 200 degrees, > EGTs 1380, Coolant 200 and when rpms reached 5100 and airspeed at 128 > mph, oil temps never went over 233 degrees. All other temps stayed > well in the green. The remote oil filter kit resolved the max temp > issues. I stayed on an east west track until I was satisfied that the > engine was happy within its full range of operation and then headed > back to Moline. Descending at 125 into the pattern was easy, the > landing was smooth and I taxied back to the south tees with 175 hours > on the engine. The cowl was unbuttoned, the engine was drip-free and > oil hoses stayed where they'd been clamped.Pictures are added > <http://www.macsmachine.com/html/subaruengine.htm> to the bottom of my > engine page that shows the components and installation in greater > detail. Very satisfied with this modification! Data was entered into > the logs. > > Larry McFarland 601HDS at www.macsmachine.com > <http://www.macsmachine.com> > > * * > * * > * * > * * > ========================http://www.matro===================http://forums.matronics.com - List Contribution Web generous nbsp; --> http://www.matronics.com/c= <http://www.matronics.com/contribution> > * * <http://www.matronics.com/contribution> > <http://www.matronics.com/contribution> > * > > > *


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:22:57 PM PST US
    From: "Larry McFarland" <larry@macsmachine.com>
    Subject: Flight Test for a Remote Oil Filter Kit on the Stratus
    Subaru Both days were in the mid-80s. I'm sure the temps were 4 or 5 degrees cooler Yesterday, so the advantage was realistically more like 10-degrees or better. Sure is easier to access. I'll have to watch the bracket for any signs of fatigue. It feels solid, but must stay that way to avoid cracking anything, lugs etc. I designed the piece so the small rod welds will be the first to show fatigue, should that occur. Larry McFarland 601HDS at www.macsmachine.com From: owner-stratus-list-server@matronics.com [mailto:owner-stratus-list-server@matronics.com] On Behalf Of Gary Krysztopik Sent: Sunday, September 11, 2011 1:20 PM Subject: Re: Stratus-List: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru Was it also 90+ degrees? If so, you went from about 250 to 233 degrees at around 130 mph and 5200 rpm. That's much more significant than I would have guessed for just a remote filter. I like where you mounted it, perfect spot with plenty of room and great airflow. Nice work, thanks. Gary Krysztopik ZWheelz, LLC - www.ZWheelz.com Alamo City Electric Auto Association - www.aceaa.org blog - http://voices.mysanantonio.com/drive_electric_san_antonio/ San Antonio, TX On 9/11/2011 11:29 AM, Larry McFarland wrote: Hi Gary, >From my journal, I'd earlier posted; Note: I often think an oil cooler might be a worthwhile addition. I had concern for oil temps that ran as high as 235 degrees F. The manual states 260 is the max oil temp permitted. Flying at 130 mph at 5200 rpm on a hot day of more than 90-degrees, engine oil will eventually reach 250 degrees (my warning set-point on the EIS) so I do back off to 4600 rpm and cruise at 115 to 120 mph. Oil temps will then stay near 235. Larry McFarland 601HDS at www.macsmachine.com From: owner-stratus-list-server@matronics.com [mailto:owner-stratus-list-server@matronics.com] On Behalf Of Gary Krysztopik Sent: Sunday, September 11, 2011 11:00 AM Subject: Re: Stratus-List: Flight Test for a Remote Oil Filter Kit on the Stratus Subaru Thanks for posting Larry. What would you say the difference is in oil temp - what would the oil temp have been below without the remote filter? Gary Krysztopik ZWheelz, LLC - www.ZWheelz.com Alamo City Electric Auto Association - www.aceaa.org blog - http://voices.mysanantonio.com/drive_electric_san_antonio/ San Antonio, TX On 9/11/2011 10:09 AM, Larry McFarland wrote: Hi guys, Sept 10 After a Hy-Vee lunch with the guys, I went to the hangar and did a thorough preflight, did take a full 5 quarts to top oil off before startup. The Subaru fired up immediately and I taxied out. Oil temps began at 60 p.s.i. and when warmed went down to 45 p.s.i. Tower cleared me for 10. The lift off was trim-adjusted with no perceptible feel for the weight change up front. I flew south of the control zone to the designated "practice area. Oil temps at 3000 feet reached 228 degrees at 4300 rpm and I progressively brought up the power in 100 rpm increments every 8 minutes or so. CHTs stayed 190 to 200 degrees, EGTs 1380, Coolant 200 and when rpms reached 5100 and airspeed at 128 mph, oil temps never went over 233 degrees. All other temps stayed well in the green. The remote oil filter kit resolved the max temp issues. I stayed on an east west track until I was satisfied that the engine was happy within its full range of operation and then headed back to Moline. Descending at 125 into the pattern was easy, the landing was smooth and I taxied back to the south tees with 175 hours on the engine. The cowl was unbuttoned, the engine was drip-free and oil hoses stayed where they'd been clamped. Pictures are added <http://www.macsmachine.com/html/subaruengine.htm> to the bottom of my engine page that shows the components and installation in greater detail. Very satisfied with this modification! Data was entered into the logs. Larry McFarland 601HDS at www.macsmachine.com ========================<p; -="" the="" stratus-list="" email="" forum="" utilities="" such="" as="" list="" photoshare,="" and="" much="" ="" -->="" http://www.matro===================<nbsp; -="" matronics="" web="" forums="" via="" the="" ="" -->="" http://forums.matronics.com - List Contribution Web generous nbsp; --> http://www.matronics.com/c= <http://www.matronics.com/contribution> </nbsp;&n bsp; ></p; > <http://www.matronics.com/contribution> <http://www.matronics.com/contribution> <http://www.matronics.com/contribution> <http://www.matronics.com/contribution> <http://www.matronics.com/contribution> <http://www.matronics.com/contribution> <http://www.matronics.com/contribution> Email Forum - Navigator to browse List Un/Subscription, 7-Day Browse, Chat, FAQ, http://www.matronics.com/Navigator?Stratus-List




    Other Matronics Email List Services

  • Post A New Message
  •   stratus-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Stratus-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/stratus-list
  • Browse Stratus-List Digests
  •   http://www.matronics.com/digest/stratus-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --