Today's Message Index:
----------------------
1. 05:17 PM - Re:wings (Eric Schlanser)
2. 05:51 PM - Re: Re:wings (john)
3. 08:33 PM - Re: Re:wings (RJ)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: Eric Schlanser <eschlanser@yahoo.com>
While we are on the subject, when do you put these holes in the wing? Before or
after applying the deck cloth wingskin covering? Eric - in Michigan
From: "john"
Subject: Tailwind-List: wings
--> Tailwind-List message posted by: "john"
Jim; What size holes are you putting in the bottom of the wings to install
the nuts that hold the flap and aileron attach bolts in place? It looks
like I should locate these before I attach the upper wing plywood. I have
epoxyed the washers in place as you suggested. Thankyou JohnD.
---------------------------------
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: "john" <frmrjohn@netonecom.net>
Eric; I'm going to put the location holes in before I install the top
skin, it will be alot easier to locate them.. It appears it will take a
minimum of a 3/4" hole, so I am thinking to go 7/16th ahead of the rearmost
spar and drill a 1/8 location hole from the inside out, than drill the final
hole from the outside. On fabric you can always use a hot tubing the size
of the hole needed in the fabric, after the fabric is on, this keeps the
fabric from fraying. JohnD
----- Original Message -----
From: "Eric Schlanser" <eschlanser@yahoo.com>
Subject: Tailwind-List: Re:wings
> --> Tailwind-List message posted by: Eric Schlanser <eschlanser@yahoo.com>
>
>
> While we are on the subject, when do you put these holes in the wing?
Before or after applying the deck cloth wingskin covering? Eric - in
Michigan
>
> From: "john"
> Subject: Tailwind-List: wings
>
> --> Tailwind-List message posted by: "john"
>
> Jim; What size holes are you putting in the bottom of the wings to install
> the nuts that hold the flap and aileron attach bolts in place? It looks
> like I should locate these before I attach the upper wing plywood. I have
> epoxyed the washers in place as you suggested. Thankyou JohnD.
>
>
> ---------------------------------
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: RJ <gatsby8898@yahoo.com>
John & Eric, I did mine after bottom skin was glued
on. Made a pilot hole from the top as John suggested,
used a 1 1/4 inch spade drill from the outside and
drilled just 1/16 in deep. Then used a 1 inch spade
drill to drill through. The result is a 1 inch hole
with a 1/8 inch shoulder to support the disc. (I'm
going to use polished aluminum). I also glued a 3/32
patch over the inside before using the spade drills.
RJ
--- john <frmrjohn@netonecom.net> wrote:
> --> Tailwind-List message posted by: "john"
> <frmrjohn@netonecom.net>
>
> Eric; I'm going to put the location holes in
> before I install the top
> skin, it will be alot easier to locate them.. It
> appears it will take a
> minimum of a 3/4" hole, so I am thinking to go
> 7/16th ahead of the rearmost
> spar and drill a 1/8 location hole from the inside
> out, than drill the final
> hole from the outside. On fabric you can always
> use a hot tubing the size
> of the hole needed in the fabric, after the fabric
> is on, this keeps the
> fabric from fraying. JohnD
> ----- Original Message -----
> From: "Eric Schlanser" <eschlanser@yahoo.com>
> To: <tailwind-list@matronics.com>
> Subject: Tailwind-List: Re:wings
>
>
> > --> Tailwind-List message posted by: Eric
> Schlanser <eschlanser@yahoo.com>
> >
> >
> > While we are on the subject, when do you put these
> holes in the wing?
> Before or after applying the deck cloth wingskin
> covering? Eric - in
> Michigan
> >
> > From: "john"
> > Subject: Tailwind-List: wings
> >
> > --> Tailwind-List message posted by: "john"
> >
> > Jim; What size holes are you putting in the bottom
> of the wings to install
> > the nuts that hold the flap and aileron attach
> bolts in place? It looks
> > like I should locate these before I attach the
> upper wing plywood. I have
> > epoxyed the washers in place as you suggested.
> Thankyou JohnD.
> >
> >
> > ---------------------------------
> >
> >
>
>
>
> Contributions
> any other
> Forums.
>
> latest messages.
> List members.
>
> http://www.matronics.com/subscription
> http://www.matronics.com/FAQ/Tailwind-List.htm
>
Digests:http://www.matronics.com/digest/tailwind-list
> http://www.matronics.com/archives
> http://www.matronics.com/photoshare
> http://www.matronics.com/emaillists
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|