Today's Message Index:
----------------------
1. 05:25 AM - Re: pANEL (Brian Alley)
2. 12:44 PM - strobe light (john)
3. 12:50 PM - book (john)
4. 12:58 PM - Re: pANEL (john)
5. 01:56 PM - Re: book (Fred Weaver)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: Brian Alley <n320wt@yahoo.com>
Bill, It's going to depend on how you plan to do your
upholstery. The panel was designed to be a very close
fit. You have room as the panel will flex slightly.
Just don't put upholstery under the mounts!
=====
BRIAN ALLEY (N320WT)
CARBON FIBER COMPOSITES
How are you going to win by a nose if you don't stick out your neck?
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: "john" <frmrjohn@netonecom.net>
Eric; I purchased my strobe from Kunzelmann in Penn. It is a streamlined
unit with an adapter for tubing which I epoxyed to the top of the fin. I
drilled and welded in place,vertical, in the top fin tubing, a tubing of
1/4" i.d. for the wire to pass through and two 1/4" pcs. of rod 3/4" long,
drilled and tapped for #6 screw, which are also welded in the top fin tube
to accept the mounting screws. I layed the fabric over the top of the fin
and after it was positioned, I put a hole in the fabric for the strobe wire
with a small soldering iron. I then install the strobe and wire, so that
the wire could be secured inside the fin before the fabric was permanetly
attached. The fabric was heat formed around the base of the strobe and
looks nice. JohnD Don't Archive,
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: "john" <frmrjohn@netonecom.net>
Rick; I received the book, Custom Built Sport Aircraft Handbood from EAA,
yesterday and it has alot of interesting info in it, thanks for the tip.
Sent in the registration material yesterday, so suspect that the tax people
will soon fall on me like a ton of bricks. JohnD Don't Archive
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Bill; I had to cut my panel down to 36"s'. Could not get the doors to
close. JohnD. Don't Archive
----- Original Message -----
From: Bill newkirk
To: tailwind-list@matronics.com
Sent: Saturday, February 14, 2004 1:37 AM
Subject: Re: Tailwind-List: pANEL
Brian;
The dimensions for the width of your panel are 36.5". The width between
my upright tubes is 36.75". This is probably too close, huh?
Bill Newkirk
-----
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: "Fred Weaver" <Mytyweav@earthlink.net>
Just remember John.... It's "just a homemade airplane"....and it didn't
cost a lot to build. Just a lot of time... got it? Taxes don't have to be
hardly anything.
Weav
----- Original Message -----
From: "john" <frmrjohn@netonecom.net>
Subject: Tailwind-List: book
> --> Tailwind-List message posted by: "john" <frmrjohn@netonecom.net>
>
> Rick; I received the book, Custom Built Sport Aircraft Handbood from EAA,
> yesterday and it has alot of interesting info in it, thanks for the tip.
> Sent in the registration material yesterday, so suspect that the tax
people
> will soon fall on me like a ton of bricks. JohnD Don't Archive
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|