Today's Message Index:
----------------------
1. 07:16 AM - Re: Cabin Heat (Eric Schlanser)
2. 03:07 PM - Re: Cabin Heat (Jim Clement)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
s=s1024; d=yahoo.com;
b=G+ihAjDUBR4kfMXYUJU1eHgdrlqi0t5O1keKFVkLvqW1iTTTq9zmI/T0J+REfJ7M9UUyp49xPU6vU7oXfBT+wP6s8pyvWH18ksdFX2M66oqNuZ9NmClJXSX1xTN5TbzXnv5aSaQU0gKV/x3scp7yDbbX7lmvaGI5Yv46ip8+nH4=
;
Jim,
Now that your camera is working can you show how this clever heat box works? Especially
the slider. Does it have springs on it to return it to the closed position?
Can it be adapted for windshield defrost?
Thanks, Eric
Jim and Donna Clement <168x@merr.com> wrote:
--> Tailwind-List message posted by: "Jim and Donna Clement" <168x@merr.com>
The hose clamp that is riveted to the small end. The funnel opens up to put
over the exhaust pipe and a few screws to close up. Mine takes in two pipes
as they both exit the same side and this fastens on as near the firewall as
you can.
The heat bos is 3" wide, 6" long and 1" deep. and closed at one end. It has
a 3/4" flange bent out on each side of the 6" base. 2" inlet on the front
and back, straight thru when the slider is pulled open. The slider has the
the end bent up to close the box when it is pulled past the 2" inlet.
I will have to read the instructions on my camera so I can post pictures, it
is hard to describe how this thing works. Jim C
---------------------------------
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Eric, It is riveted together and mounted on the firewall. Way to much work to take
it off and then take it apart for a picture. I will make a drawing of it and
send it to you when you are ready for it. Jim
----- Original Message -----
From: Eric Schlanser
To: tailwind-list@matronics.com
Sent: Tuesday, February 08, 2005 9:16 AM
Subject: Re: Tailwind-List: Cabin Heat
Jim,
Now that your camera is working can you show how this clever heat box works?
Especially the slider. Does it have springs on it to return it to the closed position?
Can it be adapted for windshield defrost?
Thanks, Eric
Jim and Donna Clement <168x@merr.com> wrote:
--> Tailwind-List message posted by: "Jim and Donna Clement" <168x@merr.com>
The hose clamp that is riveted to the small end. The funnel opens up to put
over the exhaust pipe and a few screws to close up. Mine takes in two pipes
as they both exit the same side and this fastens on as near the firewall as
you can.
The heat bos is 3" wide, 6" long and 1" deep. and closed at one end. It has
a 3/4" flange bent out on each side of the 6" base. 2" inlet on the front
and back, straight thru when the slider is pulled open. The slider has the
the end bent up to close the box when it is pulled past the 2" inlet.
I will have to read the instructions on my camera so I can post pictures, it
is hard to describe how this thing works. Jim C
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|