Today's Message Index:
----------------------
1. 04:47 AM - Sumps & carbs (Robert Ardis)
2. 05:51 AM - Re: Sumps & carbs (dmagaw@att.net)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Tailwind-List message posted by: "Robert Ardis" <ardis_rb@hotmail.com>
ADVICE NEEDED----
i have had Tailwind N4090K since about '75. I fitted it with a GPU
(0-290) and used a
0-320 sump and a MA3 carb but didn't work well and eventually friend traded
me a sump
the the carb would fit.
I started a rebuild and modification about 10 years ago and am now
about to hang
a 0-320 that has a sump with the 'flared' riser. The opening in the sump is
2.4" across
but the carb, a MS MA4SPA (10-5009) is only 2" but will fit.
I would appreciate any imput as to the 'right' carb (part #) to use
with the 'flared'
riser. I have a O-320 sump with a straight riser but not sure the 10-5009
is for it
I would appreciate any and all information.
THANKS
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Sumps & carbs |
Robert:
I don't know the answer to your questions, but you might get a better response
to your questions in the "Lycoming" Yahoo Group which has some very helpful and
knowledgable people responding on it.
http://groups.yahoo.com/group/lycoming/
Dave M
> --> Tailwind-List message posted by: "Robert Ardis"
>
> ADVICE NEEDED----
> i have had Tailwind N4090K since about '75. I fitted it with a GPU
> (0-290) and used a
> 0-320 sump and a MA3 carb but didn't work well and eventually friend traded
> me a sump
> the the carb would fit.
> I started a rebuild and modification about 10 years ago and am now
> about to hang
> a 0-320 that has a sump with the 'flared' riser. The opening in the sump is
> 2.4" across
> but the carb, a MS MA4SPA (10-5009) is only 2" but will fit.
> I would appreciate any imput as to the 'right' carb (part #) to use
> with the 'flared'
> riser. I have a O-320 sump with a straight riser but not sure the 10-5009
> is for it
> I would appreciate any and all information.
> THANKS
>
> _________________________________________________________________
<!-- BEGIN WEBMAIL STATIONERY -->
<!-- WEBMAIL STATIONERY noneset -->
Robert:
I don't know the answer to your questions, but you might get a better response
to your questions in the "Lycoming" Yahoo Group which has some very helpful and
knowledgable people responding on it.
http://groups.yahoo.com/group/lycoming/
Dave M
-- Tailwind-List message posted by: "Robert Ardis" <ARDIS_RB@HOTMAIL.COM>
ADVICE NEEDED----
i have had Tailwind N4090K since about '75. I fitted it with a GPU
(0-290) and used a
0-320 sump and a MA3 carb but didn't work well and eventually friend traded
me a sump
the the carb would fit.
I started a rebuild and modification about 10 years ago and am now
about to hang
a 0-320 that has a sump with the 'flared' riser. The opening in the sump is
2.4" across
but the carb, a MS MA4SPA (10-5009) is only 2" but will fit.
I would appreciate any imput as to the 'right' carb (part #) to use
with the 'flared'
riser. I have a O-320 sump with a straight riser but not sure the 10-5009
is for it
I would appreciate any and all information.
THANKS
_________________________________________________________________
<!-- END WEBMAIL STATIONERY -->
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|