---------------------------------------------------------- TeamGrumman-List Digest Archive --- Total Messages Posted Tue 08/05/03: 11 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 10:04 AM - Re: New Cheetah Muffler, Not Fitting? (Aucountry@aol.com) 2. 10:35 AM - Re: Re: New Cheetah Muffler, Not Fitting? (Roger Tracy) 3. 03:05 PM - Re: Re: New Cheetah Muffler, Not Fitting? (Bradley Kidder) 4. 03:12 PM - Re: Re: New Cheetah Muffler, Not Fitting? (bob milligan) 5. 03:57 PM - Strange Characters (Bradley Kidder) 6. 07:32 PM - Re: Strange Characters (Matt Dralle) 7. 08:02 PM - Re: Re: New Cheetah Muffler, Not Fitting? (flyv35b) 8. 09:16 PM - Re: New Cheetah Muffler, Not Fitting? (Aucountry@aol.com) 9. 09:37 PM - Re: Powder coat nose strut (Aucountry@aol.com) 10. 09:43 PM - Re: Re: New Cheetah Muffler, Not Fitting? (Aucountry@aol.com) 11. 09:45 PM - Re: Re: New Cheetah Muffler, Not Fitting? (Aucountry@aol.com) ________________________________ Message 1 _____________________________________ Time: 10:04:30 AM PST US From: Aucountry@aol.com Subject: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: Aucountry@aol.com In a message dated 08/04/03 09:20:46 PM, wjwilson@rn.com writes: > I'm installing a new muffler on my Cheetah, SN# 455. > The new muffler does not match up to the exhaust stacks. > The passenger side(cyl #1 and #3) have offset stacks. > IF I had 4 straight stacks, the new muffler would line up but I'm not sure > if the exhust pipe would then line up with the cowl. > > Did I get the wrong muffler? > No, I don't think you got the wrong muffler. I have never installed a muffler in 20 years that fit worth a damn. The tooling jig that is used, if indeed they do use one, is not right. Loosen the bolts that hold the exhaust risers in place and retighten them after the muffler is installed. Your next question is, "Doesn't that strain the exhaust risers, possibly causing them to fail?" Answer: "Yes, and I've seen more than one fail." Then your next question might be, "Won't it cause the exhaust gasket to leak?" Answer: "Yes, but, it's an approved process so subsituting an experiemental exhaust system that fits better is illegal." Sorry for the editorial. The truth is, aircraft quality and FAA approval are not synonomous with quality, accurate parts that fit well and are safe to use. Approved parts are approved parts because the supplier had the fortitude to sit through endless meetings with the FAA and his advisors and patience to wait out the approval process. The only serious alternative to the extremely poor quality of FAA/PMA approved exhaust systems is the Powerflow Exhaust System. Which, oddly enough, is alos approved. Expensive, but worth it. The fit is excellent except for the place where the short S-bend part hits the Carb Air SCAT tubing (on the Tiger). Can't comment on the Cheetah. ________________________________ Message 2 _____________________________________ Time: 10:35:18 AM PST US From: "Roger Tracy" Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: "Roger Tracy" I just had a riser break off clean about 30 hrs after replacing the muffer. Hopefully I'll have better luck with this one. | Your next question is, "Doesn't that strain the exhaust risers, possibly | causing them to fail?" | Answer: "Yes, and I've seen more than one fail." | ________________________________ Message 3 _____________________________________ Time: 03:05:40 PM PST US From: Bradley Kidder Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: Bradley Kidder I have the phone/address of the company that owns all of the original exhaust plans and tooling, if anybody wants it. ><((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> =B7=B4=AF`=B7.=B8. , . .=B7=B4=AF`=B7.. ><((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> Bradley Kidder N188FW AA-1 #124 "Hawg One" NTSB / EAA / AOPA / AYA ________________________________ Message 4 _____________________________________ Time: 03:12:58 PM PST US Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? From: bob milligan --> TeamGrumman-List message posted by: bob milligan Brad, here is what I get on my ol' G4 Mac: on 8/5/03 3:05 PM, Bradley Kidder at sparksnmagic@usa.net wrote: > >> <((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> > =B7=B4=AF`=B7.=B8. , . .=B7=B4=AF`=B7.. > ><((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> > Bradley Kidder > N188FW AA-1 #124 "Hawg One" > NTSB / EAA / AOPA / AYA ________________________________ Message 5 _____________________________________ Time: 03:57:35 PM PST US From: Bradley Kidder Subject: TeamGrumman-List: Strange Characters --> TeamGrumman-List message posted by: Bradley Kidder I've noticed that the Team Grumman email arrives with a lot of control codes rather than actual text. Any ideas why? Bradley Kidder N188FW AA-1 #124 "Hawg One" NTSB / EAA / AOPA / AYA ________________________________ Message 6 _____________________________________ Time: 07:32:01 PM PST US From: Matt Dralle Subject: Re: TeamGrumman-List: Strange Characters --> TeamGrumman-List message posted by: Matt Dralle That seems odd. This memssage was in plain text. Can you forward me a copy directly of a sample of the problem? Thanks, Matt At 03:56 PM 8/5/2003 Tuesday, you wrote: >--> TeamGrumman-List message posted by: Bradley Kidder > >I've noticed that the Team Grumman email arrives with a lot of control >codes rather than actual text. Any ideas why? > > >Bradley Kidder >N188FW AA-1 #124 "Hawg One" >NTSB / EAA / AOPA / AYA > > Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551 925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email http://www.matronics.com/ WWW | Featuring Products For Aircraft There's three sides to every story, babe. There's your's; there's mine; and there's the cold, hard truth... Don Henley Long Way Home, 1982 ________________________________ Message 7 _____________________________________ Time: 08:02:45 PM PST US From: "flyv35b" Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: "flyv35b" That's Dawley, right? Cliff ----- Original Message ----- From: "Bradley Kidder" Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? > --> TeamGrumman-List message posted by: Bradley Kidder > > I have the phone/address of the company that owns all of the original > exhaust plans and tooling, if anybody wants it. > > > ><((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> > =B7=B4=AF`=B7.=B8. , . .=B7=B4=AF`=B7.. ><((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> > Bradley Kidder > N188FW AA-1 #124 "Hawg One" > NTSB / EAA / AOPA / AYA > > ________________________________ Message 8 _____________________________________ Time: 09:16:32 PM PST US From: Aucountry@aol.com Subject: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: Aucountry@aol.com In a message dated 08/05/03 02:18:31 PM, i.r.m@btinternet.com writes: > Did I get the wrong muffler? > > > Sounds to me like someone has sold you an AA5 pre 75 Traveler Muffler which > fits to striaght stacks both sides. > Ian Matterface > I had a 77 Cheetah, and, as I recall, all the stacks were straight. I've only seen curved ones on a Tiger. Gary PS, Besides, if he had curved stacks, it would be off a lot further than 1/4 inch. ________________________________ Message 9 _____________________________________ Time: 09:37:35 PM PST US From: Aucountry@aol.com Subject: TeamGrumman-List: Re: Powder coat nose strut --> TeamGrumman-List message posted by: Aucountry@aol.com In a message dated 08/05/03 03:07:02 PM, gordona@moffatus.com writes: > I'm getting ready for my annual on the Tiger and would like to know if > powder coating the nose strut is okay.=A0 I've got to remove the rust and > coat it with something.=A0 Pros and cons from those with experience will be > appreciated. > Ah, well, it CAN be powder coated, but it won't be legal. I had a nose strut powder coated just for shits and grins. I had the powder coater put a weight (don't recall how much) on the spindle to see if it would come off. It didn't. I had it powder coated in satin black. I then tried to chip it with a hammer. Very, Very durable. Personally, you'll never know the condition of the bond after heating it. The power coater heated the one I did to 350 F. On another note. For the same reasons as mentioned above, I painted a nose fork with PPG Durathane (or Durethane) It's a pure poly-urethane. It was also every bit as chip resistant. Probably every bit as chip resistant as powder coating. The last time I saw it, it had been flying for 10 years with no serious blemishes. Between Durethane and Imron, I doubt you'll find anything that protects as well and lasts as long. Any of the enamels all have the same weakness in that if you get a chip, the rust will run under the paint for a long way. Enamels just don't bond as well as Urethanes, either poly or acrylic. Their only advantage is cost. It's the difference between a $10 pain job and a $60 paint job. If you ask me, for all the labor required to properly prep the strut for paint, $50 is a wise investment. Dupont makes a two part Acrylic-Urethane, Chroma-System, which is a lot easier to apply than Imron, but it's also 25% more expensive. It's almost=20as durable as a poly urethane. Almost time to get ready to go paint the cowling. It's finally cool enough to paint by midnight. Two coats of OOps Gray Imron. I'm using a SATA-JET-95 HVLP paint gun. Keep your fingers crossed. Gary www.AuCountry.com Home of "Team Grumman" TeamGrumman-List@matronics.com http://www.matronics.com/subscribe ________________________________ Message 10 ____________________________________ Time: 09:43:59 PM PST US From: Aucountry@aol.com Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: Aucountry@aol.com In a message dated 08/05/03 03:06:46 PM, sparksnmagic@usa.net writes: > I have the phone/address of the company that owns all of the original > exhaust plans and tooling, if anybody wants it. > > I;ll take you up on that offer. ________________________________ Message 11 ____________________________________ Time: 09:45:04 PM PST US From: Aucountry@aol.com Subject: Re: TeamGrumman-List: Re: New Cheetah Muffler, Not Fitting? --> TeamGrumman-List message posted by: Aucountry@aol.com In a message dated 08/05/03 03:13:56 PM, flyer.bob@verizon.net writes: > Brad, here is what I get on my ol' G4 Mac: > > on 8/5/03 3:05 PM, Bradley Kidder at sparksnmagic@usa.net wrote: > > > > >> <((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> > > =B7=B4=AF`=B7.=B8. , . .=B7=B4=AF`=B7.. > > ><((((=BA>`=B7.=B8=B8.=B7=B4=AF`=B7.=B8.=B7=B4=AF`=B7...=B8><((((=BA> > > Bradley Kidder > > N188FW AA-1 #124 "Hawg One" > > NTSB / EAA / AOPA / AYA > > > I think it;s the server not the Mac. It used to work, probably still does on Grumman Gang.