Today's Message Index:
----------------------
1. 12:16 AM - Re: TeamGrumman-List Digest: 2 Msgs - 12/09/03 (Tiger67B)
2. 10:22 AM - Stuff on eBay (czechsix@juno.com)
3. 11:56 AM - Re: Panel (Aucountry@aol.com)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: TeamGrumman-List Digest: 2 Msgs - 12/09/03 |
--> TeamGrumman-List message posted by: Tiger67B <jnpsavage@cox.net>
HEATER VENTS.. THE GOOD ONES
Barry,
You can contact Dave at 219-654-7523 or pamn@bniia.net
Once FAA approvals are obtained ,the vents will be available exclusively
from John Sjaardema of Excel-Air Service at 219-866-5587
I got some, love them, they are much better than "stock", better
material, better design, they actually work. Cost is around $65/pair as
I recall.
Jan Savage
Tiger 67B
>
> Time: 12:21:20 PM PST US
> From: N27160@aol.com
> Subject: TeamGrumman-List: Defroster-Help me Im an idiot....
>
> --> TeamGrumman-List message posted by: N27160@aol.com
>
> The AA5 glareshield sliding defroster vents have a rectangular fitting where
> the scat tubing attaches. Just how do you keep the scat tubing on, since the
> scat tubing is round and the vent fitting is rectangular?
> Is there some type of A-Dapter available, or do you just hammer to fit the
> scat tubing?
>
>
>
>
>
>
> ________________________________ Message 2 _____________________________________
>
>
> Time: 03:14:49 PM PST US
> From: FLYaDIVE@aol.com
> Subject: Re: TeamGrumman-List: Defroster-Help me Im an idiot....
>
> --> TeamGrumman-List message posted by: FLYaDIVE@aol.com
>
> In a message dated 12/9/03 3:22:09 PM Eastern Standard Time, N27160@aol.com
> writes:
>
>
>>The AA5 glareshield sliding defroster vents have a rectangular fitting
>
> where
>
>> the scat tubing attaches. Just how do you keep the scat tubing on, since
>>the
>> scat tubing is round and the vent fitting is rectangular?
>> Is there some type of A-Dapter available, or do you just hammer to fit the
>> scat tubing?
>
> =============
> Something is not right ... the old/origional design heater vent has a short
> piece of aluminum riveted onto it that takes the basic rectangular hole to a
> sloppy oval hole. The SCAT tube is aggressively pressed up over this oval and
>
> tried to be held on with ty-wraps.
>
> The second method is to use RTV sealant to help hold the SCAT tubing, this of
> course is a more permanent installation and does not lend itself well to
> maintenance.
>
> The third method is --- One of the AYA'ers did a mold that replaces the
> entire defroster heater vent and has a very nice lip that the SCAT tube slips
over
>
> and stays while you install a ty-wrap.
>
> SORRY, but I do not recall his name or phone number, he use to advertise in
> the STAR but I just looked and could not find his ad.
>
> Will the mold maker/AYA member please chime in.
>
> Barry
> "Chop'd Liver"
>
>
>
--
Call or email me for information on a NEW 2003 TIGER airplane,
and be sure to check out TIGER AIRCRAFT'S NEW WEBSITE AT:
www.tigeraircraft.com
or visit our PERSONAL WEBSITE at: http://www.geocities.com/tiger67bravo/
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> TeamGrumman-List message posted by: czechsix@juno.com
Guys,
I have a few things on eBay if anyone's interested. If the link doesn't work just
search on the item number. If you have questions please contact me OFF LIST.
Thanks and Do Not Archive!
--Mark Navratil
Cedar Rapids, Iowa
RV-8A N2D finishing....
Turn Coordinator, item #2447588004
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2447588004
Andair Mini Gascolator, item #2447590842
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2447590842
Bendix Mags, item #2447592770
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2447592770
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> TeamGrumman-List message posted by: Aucountry@aol.com
In a message dated 12/09/03 09:43:46 PM, ardri@comcast.net writes:
> I got the panel back from the powdercoat shop today. They did a nice
> job. I'm putting the placards on it now. The only thing is, the decal
> sets I have are too old to have GPS stickers. Do you use a label printer
> of some kind for this, or is there someplace to get more up-to-date
> decals (ideally the foil kind, since they would match the Grumman
> placards from FletchAir)?
>
Check around. There are companies, even auto body decal shops, that make
decals. Look on the internet. Also, there are label makers you can get from
places like Staples, that make labels. There is even software you can get to
print labels on your computer.
Gary
Any other ideas from Team Grumman?
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|