Today's Message Index:
----------------------
1. 08:30 AM - Re: screws for mag wires (flyv35b)
2. 06:29 PM - SCAT Secrets? (Steven Jackson)
3. 07:36 PM - Re: SCAT Secrets? (FLYaDIVE@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: screws for mag wires |
--> TeamGrumman-List message posted by: "flyv35b" <flyv35b@ashcreekwireless.com>
> I did notice that the Slick mag harness didn't come with "O" rings like
the
> cheaper harness does. Any ideas where I can get the "O" rings ?
O-rings for what?
----- Original Message -----
From: <TeamGrumman@aol.com>
Subject: Re: TeamGrumman-List: screws for mag wires
> --> TeamGrumman-List message posted by: TeamGrumman@aol.com
>
>
> In a message dated 5/30/04 12:08:27 AM, flyer.bob@verizon.net writes:
>
>
> > Gary,=A0 You might get lucky and find that Ron Monson, owner of=A0
> > Performance Aero Engines at Bracket may have the screws you need.=A0
He=A0
> > overhauls lots of engines and replaces lots of mags.
> >
> > Performance Aero:=A0 909-593-5008
> >
>
> Thanks. Today I cleaned my hangar and found the screws under a rag on a
> shelf for things I was setting aside to sell.
>
> I did notice that the Slick mag harness didn't come with "O" rings like
the
> cheaper harness does. Any ideas where I can get the "O" rings ?
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> TeamGrumman-List message posted by: "Steven Jackson" <steven.jackson14@adelphia.net>
TG,
Any techniques to cutting SCAT tubing to get nice, clean cuts?
Steven Jackson
'75 AA-1B
N1434R
L22
Yucca Valley, CA
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: SCAT Secrets? |
--> TeamGrumman-List message posted by: FLYaDIVE@aol.com
In a message dated 6/1/04 9:29:53 PM Eastern Daylight Time,
steven.jackson14@adelphia.net writes:
> TG,
>
> Any techniques to cutting SCAT tubing to get nice, clean cuts?
>
> Steven Jackson
> '75 AA-1B
> N1434R
> L22
> Yucca Valley, CA
====================
Steve:
Here is a simple trick, it is great for those that do not have the eye to
straighten things that are curved.
Take a piece of 1" wide masking tape and wrap it around the SCAT Tube where
you want it to be cut.
Then using a sharp razor blade cut on the edge that you want to use ...
Careful there are two edges to the tape!
When you reach the WIRE use a good pair of diagonal cutters (DIKES).
Then bend the wire back and away from the SCAT Tube, far enough to give you a
nice smooth wire free area, this is the area you clamp on.
Then CUT OFF the striped back wire, leaving about 1"
Then using a pair of needle nose pliers bend the 1" wire back 180 Deg to form
a smooth edge ... this is so the wire does not cut a hole through the SCAT
Tubing.
That is it ... easy ... took me longer to write this than to do it.
Barry
"Chop'd Liver"
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|