----------------------------------------------------------
                           TeamGrumman-List Digest Archive
                                      ---
                     Total Messages Posted Tue 06/01/04: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 08:30 AM - Re: screws for mag wires  (flyv35b)
     2. 06:29 PM - SCAT Secrets?  (Steven Jackson)
     3. 07:36 PM - Re: SCAT Secrets?  (FLYaDIVE@aol.com)
 
 
 
________________________________  Message 1  _____________________________________


Time: 08:30:53 AM PST US
From: "flyv35b" <flyv35b@ashcreekwireless.com>
Subject: Re: TeamGrumman-List: screws for mag wires

--> TeamGrumman-List message posted by: "flyv35b" <flyv35b@ashcreekwireless.com>

> I did notice that the Slick mag harness didn't come with "O" rings like
the
> cheaper harness does.   Any ideas where I can get the "O" rings ?

O-rings for what?
----- Original Message -----
From: <TeamGrumman@aol.com>
Subject: Re: TeamGrumman-List: screws for mag wires


> --> TeamGrumman-List message posted by: TeamGrumman@aol.com
>
>
> In a message dated 5/30/04 12:08:27 AM, flyer.bob@verizon.net writes:
>
>
> > Gary,=A0 You might get lucky and find that Ron Monson, owner of=A0
> > Performance Aero Engines at Bracket may have the screws you need.=A0
He=A0
> > overhauls lots of engines and replaces lots of mags.
> >
> > Performance Aero:=A0 909-593-5008
> >
>
> Thanks.   Today I cleaned my hangar and found the screws under a rag on a
> shelf for things I was setting aside to sell.
>
> I did notice that the Slick mag harness didn't come with "O" rings like
the
> cheaper harness does.   Any ideas where I can get the "O" rings ?
>
>






________________________________  Message 2  _____________________________________


Time: 06:29:20 PM PST US
From: "Steven Jackson" <steven.jackson14@adelphia.net>
Subject: TeamGrumman-List: SCAT Secrets?

--> TeamGrumman-List message posted by: "Steven Jackson" <steven.jackson14@adelphia.net>

TG,

Any techniques to cutting SCAT tubing to get nice, clean cuts?

Steven Jackson
'75 AA-1B
N1434R
L22
Yucca Valley, CA






________________________________  Message 3  _____________________________________


Time: 07:36:22 PM PST US
From: FLYaDIVE@aol.com
Subject: Re: TeamGrumman-List: SCAT Secrets?

--> TeamGrumman-List message posted by: FLYaDIVE@aol.com

In a message dated 6/1/04 9:29:53 PM Eastern Daylight Time, 
steven.jackson14@adelphia.net writes:

> TG,
>  
>  Any techniques to cutting SCAT tubing to get nice, clean cuts?
>  
>  Steven Jackson
>  '75 AA-1B
>  N1434R
>  L22
>  Yucca Valley, CA
====================
Steve:

Here is a simple trick, it is great for those that do not have the eye to 
straighten things that are curved.

Take a piece of 1" wide masking tape and wrap it around the SCAT Tube where 
you want it to be cut.
Then using a sharp razor blade cut on the edge that you want to use ... 
Careful there are two edges to the tape!
When you reach the WIRE use a good pair of diagonal cutters (DIKES).
Then bend the wire back and away from the SCAT Tube, far enough to give you a 
nice smooth wire free area, this is the area you clamp on.
Then CUT OFF the striped back wire, leaving about 1"
Then using a pair of needle nose pliers bend the 1" wire back 180 Deg to form 
a smooth edge ... this is so the wire does not cut a hole through the SCAT 
Tubing.

That is it ... easy ... took me longer to write this than to do it.

Barry
"Chop'd Liver"