Today's Message Index:
----------------------
1. 08:58 AM - Re: XDP4000X-List Digest: 5 Msgs - 02/28/03 (Freebird6512@aol.com)
2. 10:30 AM - Re: Re: XDP4000X-List Digest: 5 Msgs - 02/28/03 (Henry Faison)
3. 10:55 AM - 4K control (Henry Faison)
4. 11:03 AM - Re: 4K control (Matt Dralle)
5. 12:23 PM - Re: 4K control (NOTGSXR@aol.com)
6. 10:25 PM - Re: 4K control (owner-xdp4000x-list-server@matronics.com)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: XDP4000X-List Digest: 5 Msgs - 02/28/03 |
--> XDP4000X-List message posted by: Freebird6512@aol.com
i have a major question-
well 2 of them-
i ve been on this list for a little bit
but question
#1
do i use regular rcs type to run all of my signal bacvk to the processor(myne
is on order from a great source!)
#2
how do i get on this e-mail forum, when i have switched screen names on
aol?
thanks for everyones time!!!!
tim koehle
toledo ohio
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: XDP4000X-List Digest: 5 Msgs - 02/28/03 |
--> XDP4000X-List message posted by: "Henry Faison" <hfaison@nc.rr.com>
How to I post to the list, Help. Thank you, Henry
-----Original Message-----
From: owner-xdp4000x-list-server@matronics.com
[mailto:owner-xdp4000x-list-server@matronics.com]On Behalf Of
Freebird6512@aol.com
Subject: XDP4000X-List: Re: XDP4000X-List Digest: 5 Msgs - 02/28/03
--> XDP4000X-List message posted by: Freebird6512@aol.com
i have a major question-
well 2 of them-
i ve been on this list for a little bit
but question
#1
do i use regular rcs type to run all of my signal bacvk to the
processor(myne
is on order from a great source!)
#2
how do i get on this e-mail forum, when i have switched screen names on
aol?
thanks for everyones time!!!!
tim koehle
toledo ohio
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> XDP4000X-List message posted by: "Henry Faison" <hfaison@nc.rr.com>
Is anyone using the 4k control, if so how to you set the crossover points.
Thank you, Henry
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> XDP4000X-List message posted by: Matt Dralle <dralle@matronics.com>
At 10:55 AM 3/1/2003 Saturday, you wrote:
>--> XDP4000X-List message posted by: "Henry Faison" <hfaison@nc.rr.com>
>
>Is anyone using the 4k control, if so how to you set the crossover points.
>Thank you, Henry
Hi Henry,
4kControl doesn't currently support Xover control, only EQ control. The
next version will support Xover control, but development is currently on
the back burner.
Matt Dralle
Matronics
Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551
925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email
http://www.matronics.com/ WWW | Featuring Products For Aircraft
There's three sides to every story, babe. There's your's;
there's mine; and there's the cold, hard truth...
Don Henley
Long Way Home, 1982
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> XDP4000X-List message posted by: NOTGSXR@aol.com
In a message dated 3/1/03 2:04:10 PM Eastern Standard Time,
dralle@matronics.com writes:
> 4kControl doesn't currently support Xover control, only EQ control. The
> next version will support Xover control, but development is currently on
> the back burner.
>
> Matt Dralle
> Matronics
Matt, did i read somewhere where you were trying to change the Xover points
also? Kind of "Reverse Engineer" the unit to see all possibilities..... If
memory serves me you mentioned there could be something like 256
possibilities of Xover points or soemthing along those lines..... The # is
probably off, but didn't you get into a little research about this? Thanks
Dan
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> XDP4000X-List message posted by:
So is it posible to make the EQ settings through the 4kControl and the
Xovers though the DSC?
-Edu
----- Original Message -----
From: "Matt Dralle" <dralle@matronics.com>
Subject: Re: XDP4000X-List: 4K control
--> XDP4000X-List message posted by: Matt Dralle <dralle@matronics.com>
At 10:55 AM 3/1/2003 Saturday, you wrote:
>--> XDP4000X-List message posted by: "Henry Faison" <hfaison@nc.rr.com>
>
>Is anyone using the 4k control, if so how to you set the crossover points.
>Thank you, Henry
Hi Henry,
4kControl doesn't currently support Xover control, only EQ control. The
next version will support Xover control, but development is currently on
the back burner.
Matt Dralle
Matronics
Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551
925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email
http://www.matronics.com/ WWW | Featuring Products For Aircraft
There's three sides to every story, babe. There's your's;
there's mine; and there's the cold, hard truth...
Don Henley
Long Way Home, 1982
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|