XDP4000X-List Digest Archive

Tue 10/26/04


Total Messages Posted: 1



Today's Message Index:
----------------------
 
     1. 11:07 AM - Re: Broken XDP-210??? (Roland M)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:07:19 AM PST US
    From: "Roland M" <mdx400@hotmail.com>
    Subject: Broken XDP-210???
    --> XDP4000X-List message posted by: "Roland M" <mdx400@hotmail.com> >--> XDP4000X-List message posted by: Carl Renaghan <orudus@yahoo.com> > >I bought an XDP-210 from someone in the >EliteCarAudio.com forums. When I hooked it up to my >C90, the C90 does not power up. If I unhook it, the >C90 comes back alive. > >I am using an Alpine bus cable (I am told its the same >as Sonys). > >Any ideas? > Like Bobby suggested, check the remote output terminals connections--they are both OUTputs, the one one the HU and the one on the XDP both output +12V when the system is on. So make sure the only thing either is connected to is/are amplifier(s). The Alpine Ai-Net cable is indeed the same thing as the Sony cable and it should work correctly though, as Bobby stated as well the cable might be defective. Also make sure the UniLink cable is connected to the correct port on the XDP! The labels can sometimes be confusing because you want to connect the cable from the HU to the UniLink *output* connection on the XDP. I'm pretty sure it is the output connection you want. Because the UniLink connection on HUs is known as the UniLink or BUS Input. I know that I always get confused with that and think that the input on the slave units is supposed to be used but it is the other way around. That might be your problem as well. The other thing I would check, is the fuse on the XDP. Somehow I blew mine mysteriously (perhaps I had touched a wire or something) and the result was the same. Neither the HU or the XDP would power up. I checked all connections and eventually found the fuse on the XDP blown. Replaced it and everything was back up and running properly. Another thing to do is to press the RESET button on the main unit once you have connected everything. It should really automatically perform a BUS reset when you connect everything but just in case, hit the reset button if everything else as failed to reset the entire system. Roland M. Check out Election 2004 for up-to-date election news, plus voter tools and




    Other Matronics Email List Services

  • Post A New Message
  •   xdp4000x-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/XDP4000X-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/xdp4000x-list
  • Browse XDP4000X-List Digests
  •   http://www.matronics.com/digest/xdp4000x-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --