Today's Message Index:
----------------------
1. 07:23 AM - Re: Re: XDP4000X-List Digest: 3 Msgs - 02/01/05 (Ethan)
2. 09:32 AM - Re: Re: XDP4000X-List Digest: 3 Msgs - 02/01/05 (Roland M)
3. 12:06 PM - Re: Re: XDP4000X-List Digest: 3 Msgs - 02/01/05 (Ethan)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: XDP4000X-List Digest: 3 Msgs - 02/01/05 |
--> XDP4000X-List message posted by: Ethan <telmnstr@757.org>
> Pin compatible? Meaning can you swap out an 210EQ for a 4k? Yes. Any unit
> that can control the 210EQ (any UniLink master that has "DSP Control"
> essentially) can also control the 4000x. There are some exceptions but that
> would mainly pertain to the very early UniLink masters which were designed
> to go with the U50D only. (For instance my MDX-400, if I were using it as a
> master with it's pre-amp box cannot properly control the 210EQ and it would
> follow that it can't control the 4000X, but it can control the U50D
> properly).
> Roland M.
I meant the actual DAC IC in the 210eq and the 4000x, could you replace
the DAC ICs in the 210eq with the same ones that are in the 4000x.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: XDP4000X-List Digest: 3 Msgs - 02/01/05 |
--> XDP4000X-List message posted by: "Roland M" <mdx400@hotmail.com>
>--> XDP4000X-List message posted by: Ethan <telmnstr@757.org>
>
>
> > Pin compatible?
>
>I meant the actual DAC IC in the 210eq and the 4000x, could you replace
>the DAC ICs in the 210eq with the same ones that are in the 4000x.
>
I think that is highly doubtful, the two have completely different circuit
designs. The D/As aren't even the same brand (Crystal Semiconductor in the
4000x and AKM in the 210EQ) so I think it is VERY unlikely something like
that could be done.
Roland M.
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: XDP4000X-List Digest: 3 Msgs - 02/01/05 |
--> XDP4000X-List message posted by: Ethan <telmnstr@757.org>
> I think that is highly doubtful, the two have completely different circuit
> designs. The D/As aren't even the same brand (Crystal Semiconductor in the
> 4000x and AKM in the 210EQ) so I think it is VERY unlikely something like
> that could be done.
> Roland M.
Ah okay... AKM makes some DAC ICs used in some decent modern DVD players
(24bit/96khz I think?)
Any knowledge about the extra IO port on the xdp210eq? It looks like it
might be close to the unilink bus judging by the schematics for the unit.
Was there windows software or at least some way to talk to the unit via
rs232? I guess it would be possible to talk to it using the GNUNILINK
software, but you would have to reverse engineer the EQ/DSP portions of
the unilink protocol and emulate a head unit... nasty.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|