XDP4000X-List Digest Archive

Tue 12/09/08


Total Messages Posted: 1



Today's Message Index:
----------------------
 
     1. 06:27 AM - Re: Re: DVX-100 and XA-118 (Roland M)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:27:40 AM PST US
    From: Roland M <mdx400@hotmail.com>
    Subject: Re: DVX-100 and XA-118
    It wouldn't be something easy to modify... Over UniLink the changer will specify what output mode it is in (digital or analog)=3B going by that the XDP will "expect" a corresponding signal. CD Changers that have digital outputs have a switch for digital or analog mod e=2C and this is how the flag gets set in the UniLink protocol. Changers w ithout a digital output (or without a switch like the DVD changer) are perm anently set to analog mode. Unless the digital out flag is set in the chan ger protocol the XDP will not accept a digital input. So what you would have to do is find the IC on the board of the changer tha t has the digital output bit (use the service manual) and "pull" that signa l "high" or "low" (depending on what it has to be) in order to set digital output mode. It should be possible but no it's obviously not easy. There is also a second problem though... That is the fact that the XDP-210 EQ cannot decode Dolby Digital or DTS. The changer will have to be set to output PCM which would at least get you stereo audio in the digital domain. Note that DTS would not work like this=2C however=2C as I'm pretty sure t he DVD changer did not have a DTS decoder in it. (It doesn't have a full D D decoder either but all DVD players are required to be able to downmix DD multi-channel to 2ch=2C so that would work via PCM as long as you can set t he output as such.) Roland M. > Subject: XDP4000X-List: Re: DVX-100 and XA-118> From: rodriguezvidy@aol.c om> Date: Fri=2C 5 Dec 2008 17:28:00 -0800> To: xdp4000x-list@matronics.com >> > Any more info on this?> > I also have a dvx-100 with xa-118 adapter. I also have a cdx-c90 with xdp-219eq and wanted to know if it was something relitively easy to modify to use the optical out on the dvx-100 to be recog nized by the xdp-210eq.> > My soldering skills are poor by the way. Only so lder engine wire harness etc. Nothing small and delicate.> > > > > Read thi s topic online here:> > http://forums.matronics.com/viewtopic.php?p=21785 => _________________________________________________________________ Send e-mail anywhere. No map=2C no compass. http://windowslive.com/Explore/hotmail?ocid=TXT_TAGLM_WL_hotmail_acq_anyw here_122008




    Other Matronics Email List Services

  • Post A New Message
  •   xdp4000x-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/XDP4000X-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/xdp4000x-list
  • Browse XDP4000X-List Digests
  •   http://www.matronics.com/digest/xdp4000x-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --