Today's Message Index:
----------------------
1. 05:56 AM - Re: FAST Card Expiration (Jim Bernier)
2. 09:04 AM - Re: Recommendations for oil filter system (Doug Sapp)
3. 05:49 PM - Re: Yak-List Digest: 7 Msgs - 12/07/06 (Cj6sly@cs.com)
4. 06:02 PM - Flap Valve Overhaul (ByronMFox@aol.com)
5. 08:02 PM - Re: Flap Valve Overhaul (Roger Kemp)
6. 08:15 PM - Re: Re: Yak-List Digest: 7 Msgs - 12/07/06 (Doug Sapp)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | FAST Card Expiration |
Looks good.
The gear door should be easy to make. Making it functional is another matter. The
cheap look would be toi attach directly to the gear and you will have a gap
at the top of the door when retracted. Or you could hing at the top and have
a double bearing push pull rod at the base. Since the door and gear strut move
from different pivot points a push pull rod has to swivel at both ends. You have
gone this far. Go for it. It's just money. Are you getting liability insurance?
Or full coverage?
Jim
>>> rob@robinhill.com 12/13/2006 5:20 PM >>>
I just sent my original to Mike. I can send you a scanned copy.
rob
_____
From: owner-yak-list-server@matronics.com
[mailto:owner-yak-list-server@matronics.com] On Behalf Of Shane Golden
Sent: Tuesday, December 12, 2006 1:25 PM
Subject: RE: Yak-List: FAST Card Expiration
Nope
They come to me. The new FPR with my address is on the website.
http://www.flyredstar.org/T_Formation.aspx
Shane
-----Original Message-----
From: owner-yak-list-server@matronics.com
[mailto:owner-yak-list-server@matronics.com] On Behalf Of Rob Mortara
Sent: Monday, December 11, 2006 10:53 PM
Subject: RE: Yak-List: FAST Card Expiration
Do we still send them to Mike?
Rob
_____
From: owner-yak-list-server@matronics.com
[mailto:owner-yak-list-server@matronics.com] On Behalf Of Shane Golden
Sent: Monday, December 11, 2006 4:21 PM
Subject: Yak-List: FAST Card Expiration
Gentlemen (Ladies also)
If you have not submitted and FPR for 2006 please do so ASAP!!! I'm about
to send all the info to the card vendor so if you have not submitted an FPR
you will not receive a card with FAST credentials on the back.
If you have questions contact me off list.
Thanks,
Shane Golden
www.aeroelectric.com
www.kitlog.com
http://www.matronics.com/Navigator?Yak-List
www.aeroelectric.com
www.aeroelectric.com
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Recommendations for oil filter system |
Check out
http://www.cessna195.org/ClubEvents/Flyin2004/maintenance_forum.cfm
Some interesting items on cly base nut torquing as well as oil filters.
Always Yakin,
Doug Sapp
cjpilot710@aol.com wrote:
> In a message dated 12/11/2006 8:41:47 A.M. Eastern Standard Time,
> dsavarese@elmore.rr.com writes:
>
> I use a Marion filter and buy the S-28 10 micron filters. After an
> oil and filter change, I can easily cut open the can and check the
> filter. It has a built-in by-pass valve and a port where you can
> screw in a pressure switch if you what a 'oil by-pass' light in your
> cockpit.
>
> I've use the system on my airplane 'since day one'. I read some
> where, that contaminants in oil larger than 25 micron will cause
> engine wear. So I use the 10 micron filter. I really believe it kept
> a lot more damage from happening to the engine, when at 438 hours a
> improperly factory installed ring let go a long with some goodly
> pieces of piston.
>
> My engine has 1300 hours on it now. I use straight 50 or 60 weight
> detergent oil, changed every 30 to 35 hours. Compressions are in the
> low to mid 70's. The engine is now using around 1 qt every 1 1/2
> hours. I also have a pre-oiler which I use on the first start of each
> day.
>
> Jim "Pappy" Goolsby
>
> <dsavarese@elmore.rr.com>
>
> CJ6's with M14P's - I am looking for information on which spin on
> oil filter
> system you have added to your airplane. Any photos will also be very
> helpful.
> Thanks for your input.
> Dennis
>
> A. Dennis Savarese
> 334-285-2141 (office)
> 334-546-8182 (cell)
> www.yak-52.com
>
>*
>
>
>*
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Yak-List Digest: 7 Msgs - 12/07/06 |
Hey everybody, I mislaid the post where someone was offering to rebuild flap
valve/handles. Does anybody have that thread?
Skip Slyfield
cj6sly@cs.com
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Flap Valve Overhaul |
Bill Blackwell overhauls flap valves, Skip. billblackwell@phxinternet.net
623-703-1001
...Blitz
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Flap Valve Overhaul |
So does Carl Hayes.
Doc
----- Original Message -----
From:
Sent: 12/14/2006 8:09:26 PM
Subject: [Norton AntiSpam] Yak-List: Flap Valve Overhaul
Bill Blackwell overhauls flap valves, Skip. billblackwell@phxinternet.net 623-703-1001
...Blitz
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Yak-List Digest: 7 Msgs - 12/07/06 |
Skip,
If you don't have any luck in fixing yours, I have 6 coming via the
mail, be here in about a week to 10 days.
Always Yakin,
Doug Sapp
Cj6sly@cs.com wrote:
> Hey everybody, I mislaid the post where someone was offering to
> rebuild flap valve/handles. Does anybody have that thread?
>
> Skip Slyfield
> cj6sly@cs.com
>
>*
>
>
>*
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|