Today's Message Index:
----------------------
1. 12:31 AM - oil dilution (Mark Jefferies YAK UK)
2. 06:46 AM - Re: oil dilution (Herb Coussons)
3. 07:22 AM - Re: oil dilution (Genzlinger, Reade)
4. 09:24 AM - Re: oil dilution (Doug Sapp)
5. 11:17 AM - Re: oil dilution (cjpilot710@aol.com)
6. 11:34 AM - Re: oil dilution (Daniel Fortin)
7. 12:50 PM - Re: oil dilution (CJcanuck)
8. 12:52 PM - Required wear for this time of year.... (Tim Gagnon)
9. 12:55 PM - Re: Required wear for this time of year.... (Ashley Battles)
10. 01:38 PM - Re: Required wear for this time of year.... (Herb Coussons)
11. 02:26 PM - Re: Required wear for this time of year.... (Jon Boede)
12. 02:29 PM - Re: Required wear for this time of year.... (Ashley Battles)
13. 02:47 PM - Hey (=?ISO-8859-1?Q?H=E5vard_Dale?=)
14. 02:56 PM - Re: Hey (Jerome Van Der Schaar)
15. 03:19 PM - Re: Required wear for this time of year.... (Mark Davis)
16. 07:36 PM - Re: Required wear for this time of year.... (Roger Kemp)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Sure oil dilution is used. 2 reasons.
1. It just depends upon the ambient temperature you expect at next start up.
If its going to be below 5'c you should use it. Assuming 100 oil is in
engine.
If you don't use - expect to see oil pressure rise to normal on start up for
20 seconds then watch it drop to zero as the pump cavitates due to oil being
thick and cant get sucked through the filters and system. - DO NOT USE OIL
DILTION AT THIS STAGE !!!
80 grade oil is OK down to 0'c
2. The oil cooler can restrict flow back to the tank and bulge then split in
extreme temperatures.
Picture shows how to preheat an engine if you don't use oil dilution however
"JR" prefers to heat the engine even when oil dilution option is available.
I'm not sure how low temperature oil dilution is good for but seams to be ok
down to -10'c
http://www.yakuk.com/downloads.asp
CHEERS, MJ
Time: 10:55:01 AM PST US
From: "A. Dennis Savarese" <dsavarese@elmore.rr.com>
Subject: Re: Yak-List: Oil dilution system on M-14P
No one that I know in the Yak community uses the oil dilution system.
Dennis
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: oil dilution |
I know the east coast guys fly more in the winter - we have not been
much above 0 F or -17C (as low as -30C) for a while now.
Just curious how people are preheating. Is it something homemade, do
you use something manufactured? Do you use the stacks or the front
of the engine or the cowl flaps.
We have the EZ heat pads on the sump and the oil tank. It does ok
but the cylinders are not affected and I don't like to just sit all
winter. I generally do not fly if it is below about 20F.
Herb
On Feb 9, 2007, at 2:30 AM, Mark Jefferies YAK UK wrote:
> Sure oil dilution is used. 2 reasons.
>
>
> 1. It just depends upon the ambient temperature you expect at next
> start up.
> If its going to be below 5'c you should use it. Assuming 100 oil is in
> engine.
>
>
> If you don't use - expect to see oil pressure rise to normal on
> start up for
> 20 seconds then watch it drop to zero as the pump cavitates due to
> oil being
> thick and cant get sucked through the filters and system. - DO NOT
> USE OIL
> DILTION AT THIS STAGE !!!
>
>
> 80 grade oil is OK down to 0'c
>
>
> 2. The oil cooler can restrict flow back to the tank and bulge then
> split in
> extreme temperatures.
>
>
> Picture shows how to preheat an engine if you don't use oil
> dilution however
> "JR" prefers to heat the engine even when oil dilution option is
> available.
> I'm not sure how low temperature oil dilution is good for but seams
> to be ok
> down to -10'c
>
>
> http://www.yakuk.com/downloads.asp
>
>
> CHEERS, MJ
>
>
> Time: 10:55:01 AM PST US
>
> From: "A. Dennis Savarese" <dsavarese@elmore.rr.com>
>
> Subject: Re: Yak-List: Oil dilution system on M-14P
>
>
> No one that I know in the Yak community uses the oil dilution system.
>
> Dennis
>
> <heating_g-bzjb.jpg>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Herb:
I use a small propane heater/blower with a 4" flex aluminum pipe and 90
elbow and heat the engine from the rear. I alternate between engine and oil
cooler for 20 minutes or so. This is in conjunction with oil tank heating
pad. One prime for every 10 degrees below 70F while flipping the prop and
it starts just fine. I have never used the dilution system although I
probably should have tried it one cold morning in Winnemucca, NV.....
Also - I need to talk to you about some Wilga parts. Can you send me your
phone number off list - reade@genzlinger.net
Thanks,
Reade
> -----Original Message-----
> From: Herb Coussons [mailto:drc@wscare.com]
> Sent: Friday, February 09, 2007 9:44 AM
> To: yak-list@matronics.com
> Subject: Re: Yak-List: oil dilution
>
> {SPAM?} Header
>
> I know the east coast guys fly more in the winter - we have
> not been much above 0 F or -17C (as low as -30C) for a while now.
> Just curious how people are preheating. Is it something
> homemade, do you use something manufactured? Do you use the
> stacks or the front of the engine or the cowl flaps.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: oil dilution |
Herb and guys,
In my opinion the ultimate answer is to have a heated hanger but not all
of us can afford that so the next best option one is to always preheat
both the engine and the oil cooler with a engine pre heater such as a
Red Dragon, Herman Nelson, South Wind etc.,etc. The next best thing is
to use the combination of a fitted insulated cowl blanket and some type
of heat pad (on the oil tank), this will go a long way to solving the
problem in an unheated hanger. But without something to hold the heat
inside the cowl your are pretty much fighting a uphill battle. I
learned the benefits of cowl blankets in Alaska, I took a insulated cowl
blanket and attached a 110 volt household heat pad to the lower inside
surface of the cowl blanket with Velcro, pulled it over the cowl and it
worked wonders.
Richard is correct,don't forget the oil cooler put a EZ heat pad there
also. I have seen cold oil coolers split open like over ripe watermelons!
One last caution, don't over prime. Over priming can wash the oil from
the cly walls which will result in heavy wear in that jug. Check your
manual on this point, it is very clear about this point.
If you want a fitted cowl blanket, give me a call or a email off list, I
still have 3-4 left in stock.
Always Yakin,
Doug
Herb Coussons wrote:
>
> I know the east coast guys fly more in the winter - we have not been
> much above 0 F or -17C (as low as -30C) for a while now.
> Just curious how people are preheating. Is it something homemade, do
> you use something manufactured? Do you use the stacks or the front
> of the engine or the cowl flaps.
>
> We have the EZ heat pads on the sump and the oil tank. It does ok
> but the cylinders are not affected and I don't like to just sit all
> winter. I generally do not fly if it is below about 20F.
>
> Herb
>
>
> On Feb 9, 2007, at 2:30 AM, Mark Jefferies YAK UK wrote:
>
>> Sure oil dilution is used. 2 reasons.
>>
>>
>>
>> 1. It just depends upon the ambient temperature you expect at next
>> start up.
>> If its going to be below 5'c you should use it. Assuming 100 oil is in
>> engine.
>>
>>
>>
>> If you don't use - expect to see oil pressure rise to normal on
>> start up for
>> 20 seconds then watch it drop to zero as the pump cavitates due to
>> oil being
>> thick and cant get sucked through the filters and system. - DO NOT
>> USE OIL
>> DILTION AT THIS STAGE !!!
>>
>>
>>
>> 80 grade oil is OK down to 0'c
>>
>>
>>
>> 2. The oil cooler can restrict flow back to the tank and bulge then
>> split in
>> extreme temperatures.
>>
>>
>>
>> Picture shows how to preheat an engine if you don't use oil dilution
>> however
>> "JR" prefers to heat the engine even when oil dilution option is
>> available.
>> I'm not sure how low temperature oil dilution is good for but seams
>> to be ok
>> down to -10'c
>>
>>
>>
>> http://www.yakuk.com/downloads.asp
>>
>>
>>
>> CHEERS, MJ
>>
>>
>>
>>
>>
>> Time: 10:55:01 AM PST US
>>
>> From: "A. Dennis Savarese" <dsavarese@elmore.rr.com>
>>
>> Subject: Re: Yak-List: Oil dilution system on M-14P
>>
>>
>>
>>
>>
>> No one that I know in the Yak community uses the oil dilution system.
>>
>> Dennis
>>
>> <heating_g-bzjb.jpg>
>
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: oil dilution |
I once read an account of the early days of Alaska aviation, where pilots would
drain the still warm engine oil into a bucket after shut down. When the time
came they had to fly they would heat the bucket of oil over a camp fire or camp
stove just before starting. Maybe you could use those gas grills that get
set aside during the winter months. Should cause no small concern to the local
airport Nazis. :)
At BCT with the bomber right now. Wx is just plain beautiful. Sct to Bkn Cu at
3,000 with temp at 75F and a light wind just off the beach. We'll be flying
a ride this after noon and one in the morning. Will take the planes back to
EVB on Sunday for some maintenance pior to them starting the national tour.
Jim "Pappy" Goolsby
-----Original Message-----
From: ReadeG@Cairnwood.com
Sent: Fri, 9 Feb 2007 10:21 AM
Subject: RE: Yak-List: oil dilution
Herb:
I use a small propane heater/blower with a 4" flex aluminum pipe and 90
elbow and heat the engine from the rear. I alternate between engine and oil
cooler for 20 minutes or so. This is in conjunction with oil tank heating
pad. One prime for every 10 degrees below 70F while flipping the prop and
it starts just fine. I have never used the dilution system although I
probably should have tried it one cold morning in Winnemucca, NV.....
Also - I need to talk to you about some Wilga parts. Can you send me your
phone number off list - reade@genzlinger.net
Thanks,
Reade
> -----Original Message-----
> From: Herb Coussons [mailto:drc@wscare.com]
> Sent: Friday, February 09, 2007 9:44 AM
> To: yak-list@matronics.com
> Subject: Re: Yak-List: oil dilution
>
> {SPAM?} Header
>
> I know the east coast guys fly more in the winter - we have
> not been much above 0 F or -17C (as low as -30C) for a while now.
> Just curious how people are preheating. Is it something
> homemade, do you use something manufactured? Do you use the
> stacks or the front of the engine or the cowl flaps.
________________________________________________________________________
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: oil dilution |
Although I have never done it myself, removin the oil from the engine and
keeping it indoors during those long winter night is (was) a comon pactice
in Canadian aviation. Back in a previous life, I use to fly a Piper Cheyenne
in northern Canada and we regularly removed the battery from the airplane
when she had to sleep outside.
D
>From: cjpilot710@aol.com
>To: yak-list@matronics.com
>Subject: Re: Yak-List: oil dilution
>Date: Fri, 09 Feb 2007 14:16:23 -0500
>
>I once read an account of the early days of Alaska aviation, where pilots
>would drain the still warm engine oil into a bucket after shut down. When
>the time came they had to fly they would heat the bucket of oil over a camp
>fire or camp stove just before starting. Maybe you could use those gas
>grills that get set aside during the winter months. Should cause no small
>concern to the local airport Nazis. :)
>
>At BCT with the bomber right now. Wx is just plain beautiful. Sct to Bkn
>Cu at 3,000 with temp at 75F and a light wind just off the beach. We'll be
>flying a ride this after noon and one in the morning. Will take the planes
>back to EVB on Sunday for some maintenance pior to them starting the
>national tour.
>
>Jim "Pappy" Goolsby
>
>
>-----Original Message-----
>From: ReadeG@Cairnwood.com
>To: yak-list@matronics.com
>Sent: Fri, 9 Feb 2007 10:21 AM
>Subject: RE: Yak-List: oil dilution
>
>
>
>Herb:
>
>I use a small propane heater/blower with a 4" flex aluminum pipe and 90
>elbow and heat the engine from the rear. I alternate between engine and
>oil
>cooler for 20 minutes or so. This is in conjunction with oil tank heating
>pad. One prime for every 10 degrees below 70F while flipping the prop and
>it starts just fine. I have never used the dilution system although I
>probably should have tried it one cold morning in Winnemucca, NV.....
>
>Also - I need to talk to you about some Wilga parts. Can you send me your
>phone number off list - reade@genzlinger.net
>
>Thanks,
>
>Reade
>
> > -----Original Message-----
> > From: Herb Coussons [mailto:drc@wscare.com]
> > Sent: Friday, February 09, 2007 9:44 AM
> > To: yak-list@matronics.com
> > Subject: Re: Yak-List: oil dilution
> >
> > {SPAM?} Header
> >
> > I know the east coast guys fly more in the winter - we have
> > not been much above 0 F or -17C (as low as -30C) for a while now.
> > Just curious how people are preheating. Is it something
> > homemade, do you use something manufactured? Do you use the
> > stacks or the front of the engine or the cowl flaps.
>
>________________________________________________________________________
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: oil dilution |
A danger of using the Red Dragon units is not allowing the heat to soak into the
oil long enough. Heat a can of oil on a stove until it's too hot to touch and
you will probably still have a lump of solid oil in the middle. From my days
in G.A. here in the Great White North we always needed a minimum of 30 minutes
with the blower playing directly onto the oil pan of an IO-520 for it to be
truly effective. A big motor like the Housai (or M-14) might be longer with
it's large oil tank.
Any suggestions for a make or model of electric fan heater that I could use on
the oil cooler? I already have one of Doug's engine blankets with the E-Zheat
pads but would like to play nice with the cooler as well.
Mike
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=94012#94012
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Required wear for this time of year.... |
http://www.tundragear.com/
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=94015#94015
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Required wear for this time of year.... |
Wouldn't that make an awesome group photo at one of our clinics if we were
all wearing those....
-----Original Message-----
From: owner-yak-list-server@matronics.com
[mailto:owner-yak-list-server@matronics.com]On Behalf Of Tim Gagnon
Sent: Friday, February 09, 2007 2:53 PM
Subject: Yak-List: Required wear for this time of year....
http://www.tundragear.com/
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=94015#94015
Message 10
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Required wear for this time of year.... |
Who gets the pink grippies !! ??
(And do they come in Nomex?)
On Feb 9, 2007, at 2:57 PM, Ashley Battles wrote:
> <ashley.battles@aircapitalins.com>
>
> Wouldn't that make an awesome group photo at one of our clinics if
> we were
> all wearing those....
>
> -----Original Message-----
> From: owner-yak-list-server@matronics.com
> [mailto:owner-yak-list-server@matronics.com]On Behalf Of Tim Gagnon
> Sent: Friday, February 09, 2007 2:53 PM
> To: yak-list@matronics.com
> Subject: Yak-List: Required wear for this time of year....
>
>
>
> http://www.tundragear.com/
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=94015#94015
>
>
Message 11
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Required wear for this time of year.... |
Keep in mind that the wearing of an Ushanka with the ear flaps down is
considered "unmanly". :-)
Hey, I don't make this stuff up... http://en.wikipedia.org/wiki/Ushanka
eBay always has nice Ushankas for sale. I bought some as a joke but Holy
Cow! do they work well!
They usually go for $20-25, half of which is the shipping from Russia. You
usually have to install the pin on the front yourself, but that's pretty
easy.
Jon
>From: Herb Coussons <drc@wscare.com>
>To: yak-list@matronics.com
>Subject: Re: Yak-List: Required wear for this time of year....
>Date: Fri, 9 Feb 2007 15:37:38 -0600
>
>
>Who gets the pink grippies !! ??
>(And do they come in Nomex?)
>
>
>On Feb 9, 2007, at 2:57 PM, Ashley Battles wrote:
>
>><ashley.battles@aircapitalins.com>
>>
>>Wouldn't that make an awesome group photo at one of our clinics if we
>>were
>>all wearing those....
>>
>>-----Original Message-----
>>From: owner-yak-list-server@matronics.com
>>[mailto:owner-yak-list-server@matronics.com]On Behalf Of Tim Gagnon
>>Sent: Friday, February 09, 2007 2:53 PM
>>To: yak-list@matronics.com
>>Subject: Yak-List: Required wear for this time of year....
>>
>>
>>
>>http://www.tundragear.com/
>>
>>
>>
>>
>>Read this topic online here:
>>
>>http://forums.matronics.com/viewtopic.php?p=94015#94015
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
Message 12
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Required wear for this time of year.... |
Do you have to HAVE a pin? Will the flap stay up by itself? Wouldn't it be
cool if we started a trend in the RPA with these things? Why don't we sell
them in the store?
-----Original Message-----
From: owner-yak-list-server@matronics.com
[mailto:owner-yak-list-server@matronics.com]On Behalf Of Jon Boede
Sent: Friday, February 09, 2007 4:26 PM
Subject: Re: Yak-List: Required wear for this time of year....
Keep in mind that the wearing of an Ushanka with the ear flaps down is
considered "unmanly". :-)
Hey, I don't make this stuff up... http://en.wikipedia.org/wiki/Ushanka
eBay always has nice Ushankas for sale. I bought some as a joke but Holy
Cow! do they work well!
They usually go for $20-25, half of which is the shipping from Russia. You
usually have to install the pin on the front yourself, but that's pretty
easy.
Jon
>From: Herb Coussons <drc@wscare.com>
>To: yak-list@matronics.com
>Subject: Re: Yak-List: Required wear for this time of year....
>Date: Fri, 9 Feb 2007 15:37:38 -0600
>
>
>Who gets the pink grippies !! ??
>(And do they come in Nomex?)
>
>
>On Feb 9, 2007, at 2:57 PM, Ashley Battles wrote:
>
>><ashley.battles@aircapitalins.com>
>>
>>Wouldn't that make an awesome group photo at one of our clinics if we
>>were
>>all wearing those....
>>
>>-----Original Message-----
>>From: owner-yak-list-server@matronics.com
>>[mailto:owner-yak-list-server@matronics.com]On Behalf Of Tim Gagnon
>>Sent: Friday, February 09, 2007 2:53 PM
>>To: yak-list@matronics.com
>>Subject: Yak-List: Required wear for this time of year....
>>
>>
>>
>>http://www.tundragear.com/
>>
>>
>>
>>
>>Read this topic online here:
>>
>>http://forums.matronics.com/viewtopic.php?p=94015#94015
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
Message 13
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hey all
please visit us on www.yaknorway.com to morrow we are firing up our 52 and
fly in -20C, nice to take it out from an warm hangar and reach for the
skies...
And we are currently looking for a Yak 50 project, any one now about some
for sale?
happy flying
Havard
Message 14
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
http://www.yakkes.com/webstuff.yaksales.php
Yak Sales
-------Oorspronkelijk bericht-------
Van: Hevard Dale
Datum: 9-2-2007 23:52:02
Aan: yak-list@matronics.com
Onderwerp: Yak-List: Hey
Hey all
please visit us on www.yaknorway.com to morrow we are firing up our 52 an
d
fly in -20C, nice to take it out from an warm hangar and reach for the sk
ies
=2E.
And we are currently looking for a Yak 50 project, any one now about some
for sale?
happy flying
Havard
==========
==========
==========
Message 15
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Required wear for this time of year.... |
So what color ushankas did our comrade Soviet aviators wear?
Mark Davis
----- Original Message -----
From: "Jon Boede" <jonboede@hotmail.com>
Sent: Friday, February 09, 2007 3:25 PM
Subject: Re: Yak-List: Required wear for this time of year....
>
> Keep in mind that the wearing of an Ushanka with the ear flaps down is
> considered "unmanly". :-)
>
> Hey, I don't make this stuff up... http://en.wikipedia.org/wiki/Ushanka
>
> eBay always has nice Ushankas for sale. I bought some as a joke but Holy
> Cow! do they work well!
>
> They usually go for $20-25, half of which is the shipping from Russia.
> You usually have to install the pin on the front yourself, but that's
> pretty easy.
>
> Jon
>
>>From: Herb Coussons <drc@wscare.com>
>>To: yak-list@matronics.com
>>Subject: Re: Yak-List: Required wear for this time of year....
>>Date: Fri, 9 Feb 2007 15:37:38 -0600
>>
>>
>>Who gets the pink grippies !! ??
>>(And do they come in Nomex?)
>>
>>
>>On Feb 9, 2007, at 2:57 PM, Ashley Battles wrote:
>>
>>><ashley.battles@aircapitalins.com>
>>>
>>>Wouldn't that make an awesome group photo at one of our clinics if we
>>>were
>>>all wearing those....
>>>
>>>-----Original Message-----
>>>From: owner-yak-list-server@matronics.com
>>>[mailto:owner-yak-list-server@matronics.com]On Behalf Of Tim Gagnon
>>>Sent: Friday, February 09, 2007 2:53 PM
>>>To: yak-list@matronics.com
>>>Subject: Yak-List: Required wear for this time of year....
>>>
>>>
>>>
>>>http://www.tundragear.com/
>>>
>>>
>>>
>>>
>>>Read this topic online here:
>>>
>>>http://forums.matronics.com/viewtopic.php?p=94015#94015
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>>
>
>
>
Message 16
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Required wear for this time of year.... |
Would prefer that the Attendees be attired also. Not sure I could handle
some of our members in their BVD's as in Tim's post! The hats would be cool
for a picture.
Doc
> [Original Message]
> From: Ashley Battles <ashley.battles@aircapitalins.com>
> To: <yak-list@matronics.com>
> Date: 2/9/2007 3:01:12 PM
> Subject: RE: Yak-List: Required wear for this time of year....
>
<ashley.battles@aircapitalins.com>
>
> Wouldn't that make an awesome group photo at one of our clinics if we were
> all wearing those....
>
> -----Original Message-----
> From: owner-yak-list-server@matronics.com
> [mailto:owner-yak-list-server@matronics.com]On Behalf Of Tim Gagnon
> Sent: Friday, February 09, 2007 2:53 PM
> To: yak-list@matronics.com
> Subject: Yak-List: Required wear for this time of year....
>
>
>
> http://www.tundragear.com/
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=94015#94015
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|