Today's Message Index:
----------------------
1. 04:55 PM - Re: Exhaust Questions (David McGirt)
2. 06:15 PM - Re: Gear Selector (Forrest Johnson)
3. 07:19 PM - Re: Exhaust Questions (Robert Langford)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Exhaust Questions |
Might try Kimball
http://www.jimkimballenterprises.com/web/m14p.php
On 8/2/08 9:18 PM, "Steve Dalton" <sdalton@hughes.net> wrote:
>
> The section of exhaust with the heat shroud for cockpit heat (cylinder #8) has
> gone Tango Uniform. The inner (main) pipe appears to be too thin and burned
> thru...resulting in lots of exhaust and CO in the cockpit. NOT good!
>
> The shroud has been cut off and the pipe cobbled together with many welds,
> that are failing on a daily basis due to the thinness of the pipe. And I have
> no cockpit heat, which I will need this winter.
>
> So...my questions are:
>
> 1.) Is it possible to buy just this section with the heat shroud, or am I
> forced to buy an entire new exhaust system?
>
> 2.) If I have to buy a whole system, does anyone have any experience with/and
> recommend the "slip-joint" system vs. the stock system?
>
> Thanks,
> Steve Dalton
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=196222#196222
>
>
>
>
>
>
>
>
>
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gear Selector |
Buy a new one from Doug Sapp
----- Original Message -----
From: "TXYak" <CKeating@peoplepc.com>
Sent: Saturday, August 02, 2008 11:34 AM
Subject: Yak-List: Gear Selector
>
> I seem to have a leak at my rear gear selector. I have had it out twice
> to tighten the fittings with no luck. Any ideas? Does anybody have a
> selector for sale?
>
> Chris
> 972-489-4504
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=196179#196179
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Exhaust Questions |
Hey Guys, perhaps we should all remove and check for failure of the heat
exchange system on our Yaks, could have failed without our knowing. We all
know that stuff is colorless and oderless!!!!!!!!!!!!!!. Steve, could you
provide some pics of your system?
----- Original Message -----
From: "David McGirt" <david@mcgirt.net>
Sent: Sunday, August 03, 2008 6:50 PM
Subject: Re: Yak-List: Exhaust Questions
>
> Might try Kimball
>
> http://www.jimkimballenterprises.com/web/m14p.php
>
>
> On 8/2/08 9:18 PM, "Steve Dalton" <sdalton@hughes.net> wrote:
>
>>
>> The section of exhaust with the heat shroud for cockpit heat (cylinder
>> #8) has
>> gone Tango Uniform. The inner (main) pipe appears to be too thin and
>> burned
>> thru...resulting in lots of exhaust and CO in the cockpit. NOT good!
>>
>> The shroud has been cut off and the pipe cobbled together with many
>> welds,
>> that are failing on a daily basis due to the thinness of the pipe. And I
>> have
>> no cockpit heat, which I will need this winter.
>>
>> So...my questions are:
>>
>> 1.) Is it possible to buy just this section with the heat shroud, or am
>> I
>> forced to buy an entire new exhaust system?
>>
>> 2.) If I have to buy a whole system, does anyone have any experience
>> with/and
>> recommend the "slip-joint" system vs. the stock system?
>>
>> Thanks,
>> Steve Dalton
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=196222#196222
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> Checked by AVG.
> 5:30 PM
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|