Today's Message Index:
----------------------
1. 09:35 AM - Re: Landing light replacement for CJ (doug sapp)
2. 09:46 AM - Re: Watches of the Peoples Liberation Army (mgdimarco)
3. 09:47 AM - Re: Landing light replacement for CJ (mgdimarco)
4. 10:04 AM - Re: Landing light replacement for CJ (keithmckinley)
5. 10:37 AM - Re: Re: Watches of the Peoples Liberation Army (YakL1@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Landing light replacement for CJ |
Keith,
About your landing light:
1. They run really hot, so finger prints/grease on the glass is a factor,
wipe them down after installation.
2. When you remove a TU bulb is the glass still tight in the metal base? If
no, then you need to take some of the tension off the "ears" which hold the
bulb in place. If the bulb goes in hard you may be damaging it during
installation.
3. Have you checked the amount of amps/volts your drawing. Check both with
engine not running and with engine running with gen light off.
About the inst screws:
I do have a bit of stock here, tell me which ones you need (for which
instrument) and I'll see what I can find. Doubt I have a full set, but I
might be able to help.
Always Yakin,
Doug
On Wed, Mar 11, 2009 at 8:21 PM, keithmckinley
<keith.mckinley@townisp.com>wrote:
> keith.mckinley@townisp.com>
>
> The Chinese landing lights are just not lasting for me. Does anyone have a
> mod they could recommend that would incorporate a halogen light or some
> other high intensity light that is reasonably priced. (
>
> --------
> Keith McKinley
> 700 HS
> KFIT
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=234307#234307
>
>
--
Always Yakin,
Doug Sapp
Phone 509-826-4610
Fax 509-826-3644
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Watches of the Peoples Liberation Army |
UPDATE
The supplier blew me off since I'm ordering only 150 watches. I went looking for
another supplier and am awaiting replies.
I sent the first supplier another note and now he's interested again.
I'll let you know if the order goes through.
Mike
--------
Michael Di Marco
China Blue
mgdimarco@yahoo.com
407-608-3290
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=234342#234342
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Landing light replacement for CJ |
Replace the mount with a T-28 landing light (28v). It will require some riveting.
Mike
--------
Michael Di Marco
China Blue
mgdimarco@yahoo.com
407-608-3290
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=234343#234343
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Landing light replacement for CJ |
Thanks Doug, I'll check all of that. As for the instrument screws that was Mike
Bourget inquiring about those.
Mike, what is the source for the T-28 light?
Thanks,
Keith
--------
Keith McKinley
700 HS
KFIT
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=234347#234347
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Watches of the Peoples Liberation Army |
Thanks
In a message dated 3/12/2009 9:46:49 A.M. Pacific Daylight Time,
mgdimarco@yahoo.com writes:
--> Yak-List message posted by: "mgdimarco" <mgdimarco@yahoo.com>
UPDATE
The supplier blew me off since I'm ordering only 150 watches. I went
looking for another supplier and am awaiting replies.
I sent the first supplier another note and now he's interested again.
I'll let you know if the order goes through.
Mike
--------
Michael Di Marco
China Blue
mgdimarco@yahoo.com
407-608-3290
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=234342#234342
**************A Good Credit Score is 700 or Above. See yours in just 2 easy
steps!
%3D62%26bcd%3DfebemailfooterNO62)
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|