Today's Message Index:
----------------------
1. 04:24 AM - Re: Gill attachment replacement/fix (cjpilot710@aol.com)
2. 07:28 AM - Re: Gill attachment replacement/fix (N642K)
3. 07:36 AM - Re: Gill attachment replacement/fix (T A LEWIS)
4. 08:01 AM - Re: Gill attachment replacement/fix (doug sapp)
5. 06:01 PM - Re: Gill attachment replacement/fix (Noplugs)
6. 06:38 PM - Re: Re: Gill attachment replacement/fix (Roger Kemp)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gill attachment replacement/fix |
JC,
You can make the "thingy". It's not that hard. The "thingy" is just an
aluminum tube that has had its ends squeezed and bent, than holes drilled
at the ends. Its kind of important on how long they are and angles of th
e bends, but super dup per wise. Any A&P could make one of these "thingy"
in less than an hour. HOWEVER I happen to have some of those "thingys"
that I could not use when I replaced the gill system on CJ-6. 8Gs????
Man that must have hurt.
Jim "Pappy" Goolsby
-----Original Message-----
From: javiercarrascob <javiercarrascob@yahoo.com>
Sent: Thu, Jan 28, 2010 11:55 pm
Subject: Yak-List: Gill attachment replacement/fix
om>
Hello gang!
Hey any advice on how to repair this gill attachment bar?
Or how to replaces them... I'm talking about the thingy that holds the bar
in
lace and that connects to the engine pistons. please see the attached pict
ure.
It broke during a 8 G vertical pull.
JC
ead this topic online here:
http://forums.matronics.com/viewtopic.php?p=283884#283884
ttachments:
http://forums.matronics.com//files/gill_bar_777.jpg
-========================
========================
===========
-= - The Yak-List Email Forum -
-= Use the Matronics List Features Navigator to browse
-= the many List utilities such as List Un/Subscription,
-= Archive Search & Download, 7-Day Browse, Chat, FAQ,
-= Photoshare, and much much more:
-
-= --> http://www.matronics.com/Navigator?Yak-List
-
-========================
========================
===========
-= - MATRONICS WEB FORUMS -
-= Same great content also available via the Web Forums!
-
-= --> http://forums.matronics.com
-
-========================
========================
===========
-= - List Contribution Web Site -
-= Thank you for your generous support!
-= -Matt Dralle, List Admin.
-= --> http://www.matronics.com/contribution
-========================
========================
===========
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gill attachment replacement/fix |
8 G's? I'd continue to look for broken things and loose rivets. Especially at
the belly, center of the wings.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=283912#283912
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gill attachment replacement/fix |
What kind of aircraft did you put the 8g's on ?
Terry
----- Original Message ----
From: javiercarrascob <javiercarrascob@yahoo.com>
Sent: Thu, January 28, 2010 11:55:52 PM
Subject: Yak-List: Gill attachment replacement/fix
Hello gang!
Hey any advice on how to repair this gill attachment bar?
Or how to replaces them... I'm talking about the thingy that holds the bar in place
and that connects to the engine pistons. please see the attached picture.
It broke during a 8 G vertical pull.
JC
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=283884#283884
Attachments:
http://forums.matronics.com//files/gill_bar_777.jpg
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gill attachment replacement/fix |
JC,
Send me the length (there are 4-5 different ones on each set of gills) I
most likley have them in stock. 8 g's?? You may need more than just a
shutter standoff rod...........
Doug
On Thu, Jan 28, 2010 at 8:55 PM, javiercarrascob
<javiercarrascob@yahoo.com>wrote:
> javiercarrascob@yahoo.com>
>
> Hello gang!
>
> Hey any advice on how to repair this gill attachment bar?
>
> Or how to replaces them... I'm talking about the thingy that holds the bar
> in place and that connects to the engine pistons. please see the attached
> picture.
>
> It broke during a 8 G vertical pull.
>
> JC
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=283884#283884
>
>
> Attachments:
>
> http://forums.matronics.com//files/gill_bar_777.jpg
>
>
--
Maybe life is not the party that we were expecting,
but in the mean time, we're here, the band is playing, so we may as well
dance....."
Douglas Sapp
Doug Sapp LLC
18B Riverview Road
Omak WA 98841
PH 509-826-4610
Fax 509-826-3644
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gill attachment replacement/fix |
I would like to know where you got that nice looking seal on the outer ring, mine...well
I'm embarrassed to call it a seal.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=283994#283994
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gill attachment replacement/fix |
Try an aircraft upholstry shop. They can make one for you. The fun part will be
mounting it on the ring.
Doc
-----Original Message-----
>From: Noplugs <qas44n@yahoo.com>
>Sent: Jan 29, 2010 9:00 PM
>To: yak-list@matronics.com
>Subject: Yak-List: Re: Gill attachment replacement/fix
>
>
>I would like to know where you got that nice looking seal on the outer ring, mine...well
I'm embarrassed to call it a seal.
>
>
>Read this topic online here:
>
>http://forums.matronics.com/viewtopic.php?p=283994#283994
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|