Today's Message Index:
----------------------
1. 03:02 PM - Re: Re: Radio Noise CJ6 (okanoganlew@gmail.com)
2. 03:41 PM - YAK 50 throttle and governor cable source (Roger Kemp M.D.)
3. 06:45 PM - Re: YAK 50 throttle and governor cable source (Tom Elliott)
4. 06:58 PM - Re: CJ Trim Cable replacement (Walter Lannon)
5. 07:19 PM - Re: YAK 50 throttle and governor cable source (Roger Kemp M.D.)
6. 08:29 PM - Re: Prop Hub and Blades (Yak Driver)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Radio Noise CJ6 |
Guys, I was able to eliminate the back ground noise from my radio
transmission. And the winner is-------Brian Lloyd!! The headphones were
grounded to the airframe & when I fixed that, the noise went away. Thanks
to all for your help.
Paul Lewis
On , "Bitterlich, Mark G CIV Det Cherry Point, MALS-14 64E"
<mark.bitterlich@navy.mil> wrote:
> MALS-14 64E" mark.bitterlich@navy.mil>
> Okay.
> -----Original Message-----
> From: owner-yak-list-server@matronics.com
> [mailto:owner-yak-list-server@matronics.com] On Behalf Of Brian Lloyd
> Sent: Thursday, March 15, 2012 10:39 PM
> To: yak-list@matronics.com
> Subject: Re: Yak-List: Radio Noise CJ6
> On Thu, Mar 15, 2012 at 11:12 AM, Bitterlich, Mark G CIV Det Cherry
> Point, MALS-14 64E mark.bitterlich@navy.mil> wrote:
> Actually Brian, all informed inputs should be welcome.
> My comment to Dennis was supposed to be out-of-band. I screwed up.
> --
> Brian Lloyd, WB6RQN/J79BPL
> 3191 Western Dr.
> Cameron Park, CA 95682
> brian@lloyd.com
> +1.767.617.1365 (Dominica)
> +1.916.877.5067 (USA)
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | YAK 50 throttle and governor cable source |
Anyone know PF someone that can fabricate the 5 mm cables with metric 5mm threaded
ends for the 50.
Doc
Sent from my iPad
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | YAK 50 throttle and governor cable source |
http://www.cablecraft.com/
Give them a try. I used them to replace all of the push / pull cables
in a custom CJ.
Tom Elliott
CJ-6A NX63727
777 Quartz Ave
PMB 7004
Sandy Valley NV
89019
Cell 702-595-2680
-----Original Message-----
From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of
Roger Kemp M.D.
Sent: Sunday, March 18, 2012 3:38 PM
Subject: Yak-List: YAK 50 throttle and governor cable source
Anyone know PF someone that can fabricate the 5 mm cables with metric 5mm threaded
ends for the 50.
Doc
Sent from my iPad
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ Trim Cable replacement |
Hi Gil;
Sorry for the delay, been tied up with other less interesting but
necessary things lately. Some other CJ owners have asked for trim cable
info as well but since I don=99t have all the email addresses I
will cc to the yak-list.
There is no magic bullet for cable replacement. I will describe the
system I have used and the try to adapt it to your situation with a
failed cable and the resultant rats-nest.
1. There are two cables, one forward & one aft, which act as one
continuous cable. We will regard it as two cables, Nose Up and Nose
Down. Determine at each drum, each pulley station and the indicator
micro switch which cable is moving forward for Aircraft Nose Up (trim
tab down). Identify that cable with masking tape at each location.
Number locations front to aft starting with the forward drum.
2. Take photos of each identified location for reference.
3. Make notes for each location describing the positioning of the Nose
Up cable whether inboard or outboard on the drum, number of turns on the
drum, using an inb=99d. or outb=99d pulley and note how the
cables cross from the rear drum.
Both CJ=99s I have replaced trim cables on were early models with
the original 2 mm cable. I did not use the later Chinese 1 mm cable
choosing instead to use AN/MS standard 1/16=9D(1.6 mm) 7X19 cable
which is standard for Western aircraft trim systems and possibly more
flexible. This introduces the problem of the lead slug or swaged ball
for micro-switch actuation. I assume you will use the stock cable,
which I expect Doug can supply, so that will not be a problem. The lead
slug should be in place on the new cable but one end of each cable would
be unfinished in order to install through the drum. I don=99t
know how to install the end fitting since, as far as I know, there is no
Nico-Press or other tooling available for a 1 mm cable. Check with
Doug.
In your situation it will be difficult to identify cable & pulley
references. I had 6 or 7 photos but it appears I must have deleted
some, I can find only 3 which I will attach. There is a drawing in
the CJ6 Overhaul Manual of the system but this manual has never been
translated so the text is useless. I will get the manual from the
hangar tomorrow and make a copy of the sketch for you.
Cheers;
Walt
From: Lipaz, Gil
Sent: Friday, March 16, 2012 11:45 AM
Subject: Re: CJ Trim Cable replacement
Thanks Walt. This is my email address.
Thanks, Gil
Gil Lipaz
Senior Insurance Planning Specialist
Private Client Group
TIME Financial =93 a CRUMP Co.
1917 Livonia Ave.
Los Angeles, CA 90034
( Phone: 310.839.9727
( Phone: 310.245.7078
( Fax: 818.444.1436
* Email: glipaz@timefin.com
IRS CIRCULAR 230 NOTICE. Any advice expressed above as to tax matters
was neither written nor intended by the sender or TIME Financial
Services to be used and cannot be used by any taxpayer for the purpose
of avoiding tax penalties that may be imposed on the taxpayer. If any
such tax advice is made to any person or party, then the advice
expressed above is delivered to support the promotion or marketing of
the transaction or matter discussed or referenced. Each taxpayer should
seek advice based on the taxpayer's particular circumstances from an
independent tax advisor.
CONFIDENTIALITY NOTICE: This message is intended to be viewed only by
the listed recipient(s). It may contain information that is privileged,
confidential and/or exempt from disclosure under applicable law. Any
dissemination, distribution or copying of this message is strictly
prohibited without our prior written permission. If you are not an
intended recipient, or if you have received this communication in error,
please notify us immediately by return e-mail and permanently remove the
original message and any copies from your computer and all back-up
systems.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: YAK 50 throttle and governor cable source |
Copy... Thanks...have no idea how what "know PF someone" means though. Apple auto
correct strikes again.
Will get in touch with cable craft in the AM.
Doc
Sent from my iPad
On Mar 18, 2012, at 8:42 PM, "Tom Elliott" <N13472@aol.com> wrote:
>
> http://www.cablecraft.com/
>
> Give them a try. I used them to replace all of the push / pull cables
> in a custom CJ.
>
> Tom Elliott
> CJ-6A NX63727
> 777 Quartz Ave
> PMB 7004
> Sandy Valley NV
> 89019
> Cell 702-595-2680
>
>
> -----Original Message-----
> From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of
> Roger Kemp M.D.
> Sent: Sunday, March 18, 2012 3:38 PM
> To: Yak-List Digest Server
> Subject: Yak-List: YAK 50 throttle and governor cable source
>
>
> Anyone know PF someone that can fabricate the 5 mm cables with metric 5mm threaded
ends for the 50.
> Doc
>
> Sent from my iPad
>
>
>
>
>
>
>
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Prop Hub and Blades |
I have been trying to contact you off list but cannot seem to get through. Could
you email me: antdea2000@yahoo.com.au
Thanks.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=368863#368863
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|