---------------------------------------------------------- Yak-List Digest Archive --- Total Messages Posted Sun 03/18/12: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:02 PM - Re: Re: Radio Noise CJ6 (okanoganlew@gmail.com) 2. 03:41 PM - YAK 50 throttle and governor cable source (Roger Kemp M.D.) 3. 06:45 PM - Re: YAK 50 throttle and governor cable source (Tom Elliott) 4. 06:58 PM - Re: CJ Trim Cable replacement (Walter Lannon) 5. 07:19 PM - Re: YAK 50 throttle and governor cable source (Roger Kemp M.D.) 6. 08:29 PM - Re: Prop Hub and Blades (Yak Driver) ________________________________ Message 1 _____________________________________ Time: 03:02:46 PM PST US Subject: Re: RE: Yak-List: Radio Noise CJ6 From: okanoganlew@gmail.com Guys, I was able to eliminate the back ground noise from my radio transmission. And the winner is-------Brian Lloyd!! The headphones were grounded to the airframe & when I fixed that, the noise went away. Thanks to all for your help. Paul Lewis On , "Bitterlich, Mark G CIV Det Cherry Point, MALS-14 64E" wrote: > MALS-14 64E" mark.bitterlich@navy.mil> > Okay. > -----Original Message----- > From: owner-yak-list-server@matronics.com > [mailto:owner-yak-list-server@matronics.com] On Behalf Of Brian Lloyd > Sent: Thursday, March 15, 2012 10:39 PM > To: yak-list@matronics.com > Subject: Re: Yak-List: Radio Noise CJ6 > On Thu, Mar 15, 2012 at 11:12 AM, Bitterlich, Mark G CIV Det Cherry > Point, MALS-14 64E mark.bitterlich@navy.mil> wrote: > Actually Brian, all informed inputs should be welcome. > My comment to Dennis was supposed to be out-of-band. I screwed up. > -- > Brian Lloyd, WB6RQN/J79BPL > 3191 Western Dr. > Cameron Park, CA 95682 > brian@lloyd.com > +1.767.617.1365 (Dominica) > +1.916.877.5067 (USA) ________________________________ Message 2 _____________________________________ Time: 03:41:00 PM PST US Subject: Yak-List: YAK 50 throttle and governor cable source From: "Roger Kemp M.D." Anyone know PF someone that can fabricate the 5 mm cables with metric 5mm threaded ends for the 50. Doc Sent from my iPad ________________________________ Message 3 _____________________________________ Time: 06:45:35 PM PST US From: "Tom Elliott" Subject: RE: Yak-List: YAK 50 throttle and governor cable source http://www.cablecraft.com/ Give them a try. I used them to replace all of the push / pull cables in a custom CJ. Tom Elliott CJ-6A NX63727 777 Quartz Ave PMB 7004 Sandy Valley NV 89019 Cell 702-595-2680 -----Original Message----- From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of Roger Kemp M.D. Sent: Sunday, March 18, 2012 3:38 PM Subject: Yak-List: YAK 50 throttle and governor cable source Anyone know PF someone that can fabricate the 5 mm cables with metric 5mm threaded ends for the 50. Doc Sent from my iPad ________________________________ Message 4 _____________________________________ Time: 06:58:32 PM PST US From: "Walter Lannon" Subject: Yak-List: Re: CJ Trim Cable replacement Hi Gil; Sorry for the delay, been tied up with other less interesting but necessary things lately. Some other CJ owners have asked for trim cable info as well but since I don=99t have all the email addresses I will cc to the yak-list. There is no magic bullet for cable replacement. I will describe the system I have used and the try to adapt it to your situation with a failed cable and the resultant rats-nest. 1. There are two cables, one forward & one aft, which act as one continuous cable. We will regard it as two cables, Nose Up and Nose Down. Determine at each drum, each pulley station and the indicator micro switch which cable is moving forward for Aircraft Nose Up (trim tab down). Identify that cable with masking tape at each location. Number locations front to aft starting with the forward drum. 2. Take photos of each identified location for reference. 3. Make notes for each location describing the positioning of the Nose Up cable whether inboard or outboard on the drum, number of turns on the drum, using an inb=99d. or outb=99d pulley and note how the cables cross from the rear drum. Both CJ=99s I have replaced trim cables on were early models with the original 2 mm cable. I did not use the later Chinese 1 mm cable choosing instead to use AN/MS standard 1/16=9D(1.6 mm) 7X19 cable which is standard for Western aircraft trim systems and possibly more flexible. This introduces the problem of the lead slug or swaged ball for micro-switch actuation. I assume you will use the stock cable, which I expect Doug can supply, so that will not be a problem. The lead slug should be in place on the new cable but one end of each cable would be unfinished in order to install through the drum. I don=99t know how to install the end fitting since, as far as I know, there is no Nico-Press or other tooling available for a 1 mm cable. Check with Doug. In your situation it will be difficult to identify cable & pulley references. I had 6 or 7 photos but it appears I must have deleted some, I can find only 3 which I will attach. There is a drawing in the CJ6 Overhaul Manual of the system but this manual has never been translated so the text is useless. I will get the manual from the hangar tomorrow and make a copy of the sketch for you. Cheers; Walt From: Lipaz, Gil Sent: Friday, March 16, 2012 11:45 AM Subject: Re: CJ Trim Cable replacement Thanks Walt. This is my email address. Thanks, Gil Gil Lipaz Senior Insurance Planning Specialist Private Client Group TIME Financial =93 a CRUMP Co. 1917 Livonia Ave. Los Angeles, CA 90034 ( Phone: 310.839.9727 ( Phone: 310.245.7078 ( Fax: 818.444.1436 * Email: glipaz@timefin.com IRS CIRCULAR 230 NOTICE. Any advice expressed above as to tax matters was neither written nor intended by the sender or TIME Financial Services to be used and cannot be used by any taxpayer for the purpose of avoiding tax penalties that may be imposed on the taxpayer. If any such tax advice is made to any person or party, then the advice expressed above is delivered to support the promotion or marketing of the transaction or matter discussed or referenced. Each taxpayer should seek advice based on the taxpayer's particular circumstances from an independent tax advisor. CONFIDENTIALITY NOTICE: This message is intended to be viewed only by the listed recipient(s). It may contain information that is privileged, confidential and/or exempt from disclosure under applicable law. Any dissemination, distribution or copying of this message is strictly prohibited without our prior written permission. If you are not an intended recipient, or if you have received this communication in error, please notify us immediately by return e-mail and permanently remove the original message and any copies from your computer and all back-up systems. ________________________________ Message 5 _____________________________________ Time: 07:19:40 PM PST US Subject: Re: Yak-List: YAK 50 throttle and governor cable source From: "Roger Kemp M.D." Copy... Thanks...have no idea how what "know PF someone" means though. Apple auto correct strikes again. Will get in touch with cable craft in the AM. Doc Sent from my iPad On Mar 18, 2012, at 8:42 PM, "Tom Elliott" wrote: > > http://www.cablecraft.com/ > > Give them a try. I used them to replace all of the push / pull cables > in a custom CJ. > > Tom Elliott > CJ-6A NX63727 > 777 Quartz Ave > PMB 7004 > Sandy Valley NV > 89019 > Cell 702-595-2680 > > > -----Original Message----- > From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of > Roger Kemp M.D. > Sent: Sunday, March 18, 2012 3:38 PM > To: Yak-List Digest Server > Subject: Yak-List: YAK 50 throttle and governor cable source > > > Anyone know PF someone that can fabricate the 5 mm cables with metric 5mm threaded ends for the 50. > Doc > > Sent from my iPad > > > > > > > > > ________________________________ Message 6 _____________________________________ Time: 08:29:00 PM PST US Subject: Yak-List: Re: Prop Hub and Blades From: "Yak Driver" I have been trying to contact you off list but cannot seem to get through. Could you email me: antdea2000@yahoo.com.au Thanks. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=368863#368863 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message yak-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Yak-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/yak-list Browse Digests http://www.matronics.com/digest/yak-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.