Today's Message Index:
----------------------
1. 06:42 AM - Re: Yak Parts (Jill Gernetzke)
2. 07:03 AM - Re: Re: Yak Parts (Roger Kemp M.D.)
3. 09:56 AM - Re: Chip detector light (Roger Kemp M.D.)
4. 07:32 PM - Re: CJ6 engine exhaust system collars (CJ6XXK)
5. 08:20 PM - Re: Re: CJ6 engine exhaust system collars (doug sapp)
6. 08:37 PM - Re: CJ6 engine exhaust system collars (CJ6XXK)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Havard,
Have an upper cowling and right aileron in stock. Contact me offlist if you
are still looking.
Jill
M-14P, Inc.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Lower cowling?
Doc
Sent from my iPad
On Jun 23, 2013, at 8:38 AM, "Jill Gernetzke" <jill@m-14p.com> wrote:
>
>
> Havard,
>
> Have an upper cowling and right aileron in stock. Contact me offlist if you
> are still looking.
>
> Jill
> M-14P, Inc.
>
>
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Chip detector light |
The M-14P is one tough mutha!
Doc
Sent from my iPad
On Jun 20, 2013, at 11:00 PM, "\"" <cjpilot710@aol.com> wrote:
> I agree. Some shops or mechanics may just be a little sloppy. My M-14 en
gine came right from the factory with the wrong ring in the oil land. Ran f
or over 400 hours before making medal.
>
> Jim "Pappy" Goolsby
> -----Original Message-----
> From: Byron Fox <byronmfox@gmail.com>
> To: yak-list <yak-list@matronics.com>
> Sent: Thu, Jun 20, 2013 7:40 pm
> Subject: Re: Yak-List: Chip detector light
>
>
> Far too fine for safety wire. Doug's suggestion the it might be a bristle f
rom a
> brush used to clean the sump during its overhaul in Russia three years ago
has
> rational merit.
>
> Blitz Fox
> 415-307-2405
>
> On Jun 20, 2013, at 3:57 PM, "Tom Elliott" <N13472@aol.com> wrote:
>
> >
> > What was the diameter ? could be piece of safety wire?
> >
> >
> > Tom Elliott
> > CJ-6A NX63727
> > 777 Quartz Ave
> > PMB 7004
> > Sandy Valley NV
> > 89019
> > Cell 541-297-5497
> > N13472@AOL.COM
> >
> >
> >
> > -----Original Message-----
> > From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@
matronics.com]
> On Behalf Of
> > Byron Fox
> > Sent: Thursday, June 20, 2013 3:22 PM
> > To: Yak List
> > Subject: Yak-List: Chip detector light
> >
> > Today the chip detector light in my M14P illuminated. Nothing on the scr
een
> when removed, but this
> > very fine wire was up in tube into which the screen fits. It's about 30m
m in
> length and is sitting
> > next to a 2" paper clip in the picture. It's also steel, not stainless s
teel.
> Any thoughts?
> >
> > Only thing done differently lately was a 40 minute "Out of Control Fligh
t"
> lesson with Skip Slyfield
> > on Sunday. Pulled 4.5 Gs positive and 1G negative. Essentially a recover
y from
> unusual attitudes
> > exercise.
> >
> >
> >
> >
> >
> >
> >
> >
>
>
> et="_blank">http://www.matronics.com/Navigator?Yak-List
> tp://forums.matronics.com
> _blank">http://www.matronics.com/contribution
>
>
>
>
>
==========================
=========
==========================
=========
==========================
=========
==========================
=========
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 engine exhaust system collars |
Here is picture of items.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=403252#403252
Attachments:
http://forums.matronics.com//files/image_171.jpg
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 engine exhaust system collars |
Dan,
Could you please contact myself or Kathleen? We have been trying to reach
you without success. Your credit card on file has been declined, please
contact us so we can retire this invoice.
Best,
Doug Sapp
Ph 509-826-4610
dougsappllc@gmail.com
On Sun, Jun 23, 2013 at 7:28 PM, CJ6XXK <Danielt_355@hotmail.com> wrote:
>
> Here is picture of items.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=403252#403252
>
>
> Attachments:
>
> http://forums.matronics.com//files/image_171.jpg
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 engine exhaust system collars |
Hi Doug
You now have new email with new address.
Daniel
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=403260#403260
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|