Today's Message Index:
----------------------
 
     1. 08:58 AM - Re: YAK55m 500hr check requirments (PaulW)
     2. 04:34 PM - CJ evevator trim tabs (Kelley Monroe)
     3. 08:32 PM - HELP, I Need To Find CJ6 Fuel Pump Fittings (dbotich)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
08:58:24 AM PST US
Subject: 
Re: YAK55m 500hr check requirments
From: 
"PaulW" <paul@budcyber.com>
      
      
      Hi
      
      
      Requirement for the YAK-52 in South Africa is 600hours or 15 years.
      
      Can't comment on Factory nor '55 in South Africa.
      
      Just did the YAK-52 now for an X-Ray (engine removed to check mountings, wings
      removed, etc, etc) now and they found 1 x Wing  bolt cracked. For the rest OK.
      
      
      Paul
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=421935#421935
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:34:14 PM PST US
From: 
"Kelley Monroe" <kelmonroe@comcast.net>
Subject: 
CJ evevator trim tabs
      
      I replaced all the trim cables in my CJ and the spool on the elevator.  
      Thanks to all that send the diagram and advise.
      I now need advise on  my elevator trim tabs.
      They are warped and the finish has come off down to the wood and fiber 
      glass.  Any advise would be appreciated.  Thanks Kelley
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
08:32:49 PM PST US
Subject: 
HELP, I Need To Find CJ6 Fuel Pump Fittings
From: 
"dbotich" <david.botich@gmail.com>
      
      
      I am trying to find both the inlet and outlet fittings for my fuel pump. These
      have an M14 thread into the pump and a male flare on the ends to attach to my
      hoses. I am also trying to locate any other fittings that will allow me to connect
      my pump in and out. I believe the outlet fitting also has a connection for
      the fuel pressure line.
      
      If you know an other way to do this with SAE fittings and hoses I would like to
      hear about that.
      
      If you have any pictures what these look like installed please send me those.
      
      Thanks
      
      dbotich
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=421947#421947
      
      








Other Matronics Email List Services




Post A New Message
  
yak-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Yak-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/yak-list
Browse Yak-List Digests
  
http://www.matronics.com/digest/yak-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --