Today's Message Index:
----------------------
1. 04:31 AM - Re: Aeroquip Hose (Ernest Martinez)
2. 07:52 AM - Re: Aeroquip Hose (A. Dennis Savarese)
3. 09:36 AM - Re: Aeroquip Hose (Ernest Martinez)
4. 10:58 AM - Re: Aeroquip Hose (Bill vH)
5. 10:54 PM - Re: Aeroquip Hose (FamilyGage@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aeroquip Hose |
Dennis,
Do you think that a 303-3 hose would be sufficient for our air system?
What I'd like to do is use hose pig tails off of things like the flap valve
where it is located in tight spots. The 666 hose would have fit the bill
nicely, but the nuts can't be replaced. I'm concerned that the 303 hose is
a bit bulky.
Thanks
Ernie
On Sat, Sep 20, 2014 at 10:55 PM, A. Dennis Savarese <
dsavarese0812@bellsouth.net> wrote:
> Use Aeroquip 303 hose with AN491-x fitting. Throw away the AN nut from
> the 491-x and use the metric B-nut on the 491-x fitting. Use the
> appropriate size mandril for the 491-x fitting available from Spruce if you
> don't already have them.
> Dennis
>
>
> On Sep 20, 2014, at 3:26 PM, Ernest Martinez <erniel29@gmail.com> wrote:
>
> Has anyone been able to use the Chinese B-Nuts on Flexible hose like
> Aeroquip 666? I'd like to know what mandrels, etc I would need to make this
> work.
>
> Thanks
>
> Ernie
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aeroquip Hose |
I use Aeroquip 303-4 hoses and AN491-4 fittings. The metric B nut fits very nicely
in place of the AN B nut on the 491-4 fitting.
The 303 hose works very well. Been there, done that, got the T-shirt.
Dennis
________________________________
From: Ernest Martinez <erniel29@gmail.com>
Sent: Sunday, September 21, 2014 6:30 AM
Subject: Re: Yak-List: Aeroquip Hose
Dennis,
Do you think that a 303-3 hose would be sufficient for our air system?
What I'd like to do is use hose pig tails off of things like the flap valve where
it is located in tight spots. The 666 hose would have fit the bill nicely,
but the nuts can't be replaced. I'm concerned that the 303 hose is a bit bulky.
Thanks
Ernie
On Sat, Sep 20, 2014 at 10:55 PM, A. Dennis Savarese <dsavarese0812@bellsouth.net>
wrote:
Use Aeroquip 303 hose with AN491-x fitting. Throw away the AN nut from the 491-x
and use the metric B-nut on the 491-x fitting. Use the appropriate size mandril
for the 491-x fitting available from Spruce if you don't already have them.
>Dennis
>
>On Sep 20, 2014, at 3:26 PM, Ernest Martinez <erniel29@gmail.com> wrote:
>
>
>Has anyone been able to use the Chinese B-Nuts on Flexible hose like Aeroquip
666? I'd like to know what mandrels, etc I would need to make this work.
>>
>>
>>Thanks
>>
>>
>>Ernie
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aeroquip Hose |
Thanks Dennis, the question was will the 303-3 hose with the AN 491-3 work?
Ernie
On Sun, Sep 21, 2014 at 10:52 AM, A. Dennis Savarese <
dsavarese0812@bellsouth.net> wrote:
> I use Aeroquip 303-4 hoses and AN491-4 fittings. The metric B nut fits
> very nicely in place of the AN B nut on the 491-4 fitting.
>
> The 303 hose works very well. Been there, done that, got the T-shirt.
> Dennis
>
> ------------------------------
> *From:* Ernest Martinez <erniel29@gmail.com>
> *To:* yak-list <yak-list@matronics.com>
> *Sent:* Sunday, September 21, 2014 6:30 AM
> *Subject:* Re: Yak-List: Aeroquip Hose
>
> Dennis,
>
> Do you think that a 303-3 hose would be sufficient for our air system?
>
> What I'd like to do is use hose pig tails off of things like the flap
> valve where it is located in tight spots. The 666 hose would have fit the
> bill nicely, but the nuts can't be replaced. I'm concerned that the 303
> hose is a bit bulky.
>
> Thanks
>
> Ernie
>
> On Sat, Sep 20, 2014 at 10:55 PM, A. Dennis Savarese <
> dsavarese0812@bellsouth.net> wrote:
>
> Use Aeroquip 303 hose with AN491-x fitting. Throw away the AN nut from
> the 491-x and use the metric B-nut on the 491-x fitting. Use the
> appropriate size mandril for the 491-x fitting available from Spruce if you
> don't already have them.
> Dennis
>
>
> On Sep 20, 2014, at 3:26 PM, Ernest Martinez <erniel29@gmail.com> wrote:
>
> Has anyone been able to use the Chinese B-Nuts on Flexible hose like
> Aeroquip 666? I'd like to know what mandrels, etc I would need to make this
> work.
>
> Thanks
>
> Ernie
>
>
> *
>
>
> *
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aeroquip Hose |
Dennis,
I have looked all over (including ACS) and have never found any assembly mandrels
that have metric threads allowing you to thread on the metric B-nut and then
thread that into the hose.
I guess I don't understand why you would even buy a AN 491-X fitting if you were
going to use the metric B-nut. I just made my own assembly mandrel with an appropriate
size metric bolt on a lathe.
What am I missing here?
Bill
[quote="dsavarese0812(at)bellsout"]Use Aeroquip 303 hose with AN491-x fitting.
Throw away the AN nut from the 491-x and use the metric B-nut on the 491-x fitting.
Use the appropriate size mandril for the 491-x fitting available from Spruce
if you don't already have them.
Dennis
On Sep 20, 2014, at 3:26 PM, Ernest Martinez wrote:
> Has anyone been able to use the Chinese B-Nuts on Flexible hose like Aeroquip
666? I'd like to know what mandrels, etc I would need to make this work.
>
> Thanks
>
>
> Ernie
>
>
> >
> >
> >
> >
>
> [b]
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=430880#430880
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aeroquip Hose |
ERnie:
It is good to see you name on the Yak list. Many found memeries. Hope
that you are doing fine. Do you still live in the Ocala fly-in?
Let me hear what you have been up to.
Your Old Friend,
Ray Gage
In a message dated 9/21/2014 7:31:46 A.M. Eastern Daylight Time,
erniel29@gmail.com writes:
Dennis,
Do you think that a 303-3 hose would be sufficient for our air system?
What I'd like to do is use hose pig tails off of things like the flap
valve where it is located in tight spots. The 666 hose would have fit the bill
nicely, but the nuts can't be replaced. I'm concerned that the 303 hose is a
bit bulky.
Thanks
Ernie
On Sat, Sep 20, 2014 at 10:55 PM, A. Dennis Savarese
<_dsavarese0812@bellsouth.net_ (mailto:dsavarese0812@bellsouth.net) > wrote:
Use Aeroquip 303 hose with AN491-x fitting. Throw away the AN nut from
the 491-x and use the metric B-nut on the 491-x fitting. Use the appropriate
size mandril for the 491-x fitting available from Spruce if you don't
already have them.
Dennis
On Sep 20, 2014, at 3:26 PM, Ernest Martinez <_erniel29@gmail.com_
(mailto:erniel29@gmail.com) > wrote:
Has anyone been able to use the Chinese B-Nuts on Flexible hose like
Aeroquip 666? I'd like to know what mandrels, etc I would need to make this
work.
Thanks
Ernie
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|