Today's Message Index:
----------------------
 
     1. 04:53 PM - Re: Oil cooler inlet plug (CJ) (Lancer)
     2. 07:36 PM - Re: Re: Oil cooler inlet plug (CJ) (Walter Lannon)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:53:33 PM PST US
Subject: 
Re: Oil cooler inlet plug (CJ)
From: 
"Lancer" <lrob4783@bigpond.net.au>
      
      
      I recently did a little work on a friend's CJ and noticed through the Oil Cooler
      outlet (at the underbelly) that wasps or hornets had nested in the air passages
      in the Oil Cooler almost completely closing off the airflow. Now this was
      not visible from the inlet where most of us carry out our daily inspection. There
      had always been a plug in the inlet and these pesky critters had sneaked in
      through the "Back Door"
      
      So if you're going to plug the oil cooler inlet don't forget to make a plug for
      the outlet also. I made mine from a block of foam rubber and glued in a red tag
      so I don't forget it during my pre-flight inspection.
      
      Regards,
      
      Lance
      
      --------
      You can run but you can't hide
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=458296#458296
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
07:36:35 PM PST US
From: 
"Walter Lannon" <wlannon@shaw.ca>
Subject: 
Re: Oil cooler inlet plug (CJ)
      
      
      Thank you.
      Very good information,  I will certainly inspect mine.
      
      Walt
      
      -----Original Message----- 
      From: Lancer
      Sent: Sunday, July 17, 2016 4:52 PM
      Subject: Yak-List: Re: Oil cooler inlet plug (CJ)
      
      
      I recently did a little work on a friend's CJ and noticed through the Oil 
      Cooler outlet (at the underbelly) that wasps or hornets had nested in the 
      air passages in the Oil Cooler almost completely closing off the airflow. 
      Now this was not visible from the inlet where most of us carry out our daily 
      inspection. There had always been a plug in the inlet and these pesky 
      critters had sneaked in through the "Back Door"
      
      So if you're going to plug the oil cooler inlet don't forget to make a plug 
      for the outlet also. I made mine from a block of foam rubber and glued in a 
      red tag so I don't forget it during my pre-flight inspection.
      
      Regards,
      
      Lance
      
      --------
      You can run but you can't hide
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=458296#458296
      
      








Other Matronics Email List Services




Post A New Message
  
yak-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Yak-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/yak-list
Browse Yak-List Digests
  
http://www.matronics.com/digest/yak-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --