Today's Message Index:
----------------------
1. 01:57 AM - Re: Cylinder Questions (Lancer)
2. 05:16 PM - Which mag runs which side (JL2A)
3. 05:39 PM - (Robert Schwartz)
4. 05:45 PM - Re: Which mag runs which side (Hank Gibson)
5. 08:06 PM - Re: Which mag runs which side (A. Dennis Savarese)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cylinder Questions |
Ernie,
The wrist pin needs to be pressed from the rear of the engine and removed at the
front. I use a 3/8 socket extension...Put the large end in through the rear
retainer and it will locate in the wrist pin facilitate removal. The front retainer
is floating and will slide out when you start tapping the extension/drift.
The rear retainer is pressed in place and is not intended to be removed.
Pistons and cylinders are numbered at the factory assisting in replacing them in
the correct location.
Be careful to keep the pushrods secure in the pushrod tube specially with the lower
cylinders as the cam followers are made up of a few small parts which don't
fare too well if not seated correctly when the cylinder is refitted
Good Luck
Regards,
Lance
--------
You can run but you can't hide
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=459377#459377
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Which mag runs which side |
I'm sure I saw it in one of the manuals somewhere but now cannot seem to..
Simple one, is No1 mag on HS6A the left (port) side and does it run the front or
rear row of plugs?
Thanks!
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=459409#459409
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I saw the file download for yak electric schematics. =C2-Where do I acces
s the parts book that was discussed ?
Sent from Yahoo Mail on Android
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Which mag runs which side |
Left = front , right = rear
Sent from my iPhone
> On Aug 9, 2016, at 8:16 PM, JL2A <info@flyingwarbirds.com.au> wrote:
>
>
> I'm sure I saw it in one of the manuals somewhere but now cannot seem to..
>
> Simple one, is No1 mag on HS6A the left (port) side and does it run the front
or rear row of plugs?
>
> Thanks!
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=459409#459409
>
>
>
>
>
>
>
>
>
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Which mag runs which side |
Front.
Dennis
Sent from my iPhone
> On Aug 9, 2016, at 8:16 PM, JL2A <info@flyingwarbirds.com.au> wrote:
>
>
> I'm sure I saw it in one of the manuals somewhere but now cannot seem to..
>
> Simple one, is No1 mag on HS6A the left (port) side and does it run the front
or rear row of plugs?
>
> Thanks!
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=459409#459409
>
>
>
>
>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|