---------------------------------------------------------- Yak-List Digest Archive --- Total Messages Posted Tue 09/06/16: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:17 AM - Re: Fuel pressure (Pedro Cerveira Pinto) 2. 04:45 AM - Test only (Kevin Pilling) 3. 04:58 AM - Re: Fuel pressure (A. Dennis Savarese) 4. 06:57 AM - Re: Test only (Etienne Verhellen) 5. 07:48 AM - Yak-52 Pedal parts (Craig Payne) 6. 07:59 AM - Re: Yak-52 Pedal parts (Ernest Martinez) 7. 09:00 AM - Re: [Non-DoD Source] Re: Fuel pressure (Bitterlich, Mark G CIV NAVAIR, WD) 8. 09:42 AM - Re: Yak-52 Pedal parts (Kregg Victory) 9. 01:01 PM - Re: [Non-DoD Source] Re: Yak-52 Pedal parts (Bitterlich, Mark G CIV NAVAIR, WD) ________________________________ Message 1 _____________________________________ Time: 04:17:16 AM PST US From: Pedro Cerveira Pinto Subject: Re: Yak-List: Fuel pressure Check fuel filters first Cheers 2016-09-06 2:25 GMT+00:00 danbooker : > > At 80% rpm and 80 mp, what should the fuel pressure be? Mine is at the > bottom of the green arc at about .2? It seems like it used to be higher? > Any one know about this? > > -------- > Daniel Booker > "Stealth-Eagle Aviation" > 2312457798 > danbooker@hotmail.com > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=460284#460284 > > -- Pedro Cerveira Pinto ________________________________ Message 2 _____________________________________ Time: 04:45:32 AM PST US From: "Kevin Pilling" Subject: Yak-List: Test only --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus ________________________________ Message 3 _____________________________________ Time: 04:58:11 AM PST US Subject: Re: Yak-List: Fuel pressure From: "A. Dennis Savarese" Dan, Was it higher after the engine change? Dennis A. Dennis Savarese 334-546-8182 (mobile) www.yak-52.com Skype - Yakguy1 On 9/6/2016 6:54 AM, Pedro Cerveira Pinto wrote: > Check fuel filters first > Cheers > > 2016-09-06 2:25 GMT+00:00 danbooker >: > > > > > At 80% rpm and 80 mp, what should the fuel pressure be? Mine is at > the bottom of the green arc at about .2? It seems like it used to > be higher? Any one know about this? > > -------- > Daniel Booker > "Stealth-Eagle Aviation" > 2312457798 > danbooker@hotmail.com > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=460284#460284 > > > > =================================== > List" rel="noreferrer" > target="_blank">http://www.matronics.com/Navigator?Yak-List > =================================== > FORUMS - > eferrer" target="_blank">http://forums.matronics.com > =================================== > WIKI - > errer" target="_blank">http://wiki.matronics.com > =================================== > b Site - > -Matt Dralle, List Admin. > rel="noreferrer" target="_blank">http://www.matronics.com/contribution > =================================== > > > -- > Pedro Cerveira Pinto > ________________________________ Message 4 _____________________________________ Time: 06:57:49 AM PST US Subject: Yak-List: Re: Test only From: "Etienne Verhellen" It works Kevin ! Cheers, Etienne & Co. Yak-52 Janie G-CBSS. https://flic.kr/y/uqfU4N http://www.tvlux.be/video/info/tourisme/rassemblement-d-anciens-coucous-sur-l-aerodrome-de-saint-hubert_23445.html https://youtu.be/nz-goIVOywQ -------- Yak-52 training anywhere - FI(A) Aerobatic Instructor - Specialised Yak-52. http://www.afors.com/index.php?page=adview&adid=25551&imid=4 To Fly To Serve ... https://c2.staticflickr.com/4/3677/18982461460_03d628ac44_b.jpg Read this topic online here: http://forums.matronics.com/viewtopic.php?p=460299#460299 ________________________________ Message 5 _____________________________________ Time: 07:48:05 AM PST US From: Craig Payne Subject: Yak-List: Yak-52 Pedal parts Thanks to yak-list replies I have a source for those parts. It is the Yak-52 I'm looking to build a pedal mod for, may not fit any other model without clearance issues. Not everyone needs more leg room but I do. Hopefully I'll begin building a number of useful items for the Yak such as I have done with the Nanchang. When I have new offerings I'll post them. Craig Payne ________________________________ Message 6 _____________________________________ Time: 07:59:24 AM PST US From: Ernest Martinez Subject: Re: Yak-List: Yak-52 Pedal parts Are you flying a Yak now???? On Tue, Sep 6, 2016 at 10:47 AM, Craig Payne wrote: > Thanks to yak-list replies I have a source for those parts. It is the > Yak-52 I'm looking to build a pedal mod for, may not fit any other model > without clearance issues. Not everyone needs more leg room but I do. > > Hopefully I'll begin building a number of useful items for the Yak such as > I have done with the Nanchang. When I have new offerings I'll post them. > > Craig Payne > ________________________________ Message 7 _____________________________________ Time: 09:00:11 AM PST US From: "Bitterlich, Mark G CIV NAVAIR, WD" Subject: RE: [Non-DoD Source] Re: Yak-List: Fuel pressure On the M-14 fuel pump there is a small vent hole for the regulator on the bottom part as you look at it. I really need a picture here to point at, but in any case, if this gets blocked with bugs, garbage, etc., it can cause erratic fuel pressure as you change altitude. Happened to me. A piece of .032 safety wire (gently) will fix it. Mark -----Original Message----- From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of Walter Lannon Sent: Tuesday, September 06, 2016 1:02 AM Subject: [Non-DoD Source] Re: Yak-List: Fuel pressure Fuel press. operating range 0.2 to 0.5 Kg./ sq. cm. (approx. 3 to 7 psi). Min. idle 1.5 (2 psi) These are Huosai numbers which I believe are the same for the M14 but can't confirm at this moment. 0.2 Kg/sq. cm. is actually just slightly under 3 psi and is indeed low for a high power setting. I assume you mean 80% at 800 mm/hg rather than 80? I would expect to see about 3.5 (5 psi) for cruise and above. Very easy to adjust press. relief valve but first ensure there is no evidence of leakage. Unless the pump is very high time (high wear) should take only a small adjustment to correct. Worth checking the relief valve spring condition for possible corrosion damage. Walt -----Original Message----- From: danbooker Sent: Monday, September 05, 2016 7:25 PM Subject: Yak-List: Fuel pressure At 80% rpm and 80 mp, what should the fuel pressure be? Mine is at the bottom of the green arc at about .2? It seems like it used to be higher? Any one know about this? -------- Daniel Booker "Stealth-Eagle Aviation" 2312457798 danbooker@hotmail.com Read this topic online here: http://forums.matronics.com/viewtopic.php?p=460284#460284 ________________________________ Message 8 _____________________________________ Time: 09:42:51 AM PST US From: "Kregg Victory" Subject: RE: Yak-List: Yak-52 Pedal parts I have a set of Yak 52 pedals front and rear. Also, I have rudder pedal extensions that will work on the yaks as well Kregg Victory Victory Aero 2502 John Montgomery Dr. San Jose, CA 95148 408-836-5122 www.victoryhangar.com www.balancemyprop.com From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of Craig Payne Sent: Friday, September 02, 2016 9:34 AM Subject: Yak-List: Yak-52 Pedal parts Looking to buy or borrow rudder pedal parts from a Yak-52 carcass. I'm designing a mod to increase leg room a bit. Off-List please. Craig Payne ________________________________ Message 9 _____________________________________ Time: 01:01:34 PM PST US From: "Bitterlich, Mark G CIV NAVAIR, WD" Subject: RE: [Non-DoD Source] Yak-List: Re: Yak-52 Pedal parts Quite normal when inverted. ;-) -----Original Message----- From: owner-yak-list-server@matronics.com [mailto:owner-yak-list-server@matronics.com] On Behalf Of Ernest Martinez Sent: Monday, September 05, 2016 4:48 PM Subject: Re: [Non-DoD Source] Yak-List: Re: Yak-52 Pedal parts You step on the left pedal to go right :) On Mon, Sep 5, 2016 at 3:17 PM, Bitterlich, Mark G CIV NAVAIR, WD wrote: What is different about "your way" Craig? Curious. Mark ________________________________ From: owner-yak-list-server@matronics.com [owner-yak-list-server@matronics.com ] on behalf of Craig Payne [yakman285@gmail.com] Sent: Saturday, September 03, 2016 11:26 AM To: yak-list Subject: [Non-DoD Source] Yak-List: Re: Yak-52 Pedal parts Yes, I know it has been done before...but not my way. I calculate 1.6" improvement. I'm also looking to make an adjustable seat mod. I just need a Yak-52 "mule" near Lakeland. Craig Payne ===================================== List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?Yak-List =================================== FORUMS - eferrer" target="_blank">http://forums.matronics.com =================================== WIKI - errer" target="_blank">http://wiki.matronics.com =================================== b Site - -Matt Dralle, List Admin. rel="noreferrer" target="_blank">http://www.matronics.com/contribution =================================== ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message yak-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Yak-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/yak-list Browse Digests http://www.matronics.com/digest/yak-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.