Today's Message Index:
----------------------
1. 02:59 AM - Re: "Battery On" light rear cockpit (Rob Rowe)
2. 04:06 AM - Russian clock with electrical connectors (Jan Mevis)
3. 04:11 AM - Re: Russian clock with electrical connectors (Didier Blouzard)
4. 04:12 AM - Re: Russian clock with electrical connectors (Didier Blouzard)
5. 04:38 AM - Re: Russian clock with electrical connectors (A. Dennis Savarese)
6. 04:46 AM - Re: Russian clock with electrical connectors (Vic)
7. 04:51 AM - Re: Russian clock with electrical connectors (Jan Mevis)
8. 04:54 AM - Re: Russian clock with electrical connectors (George Coy)
9. 05:13 AM - Re: Russian clock with electrical connectors (George Coy)
10. 05:13 AM - Re: Russian clock with electrical connectors (Richard Goode)
11. 05:14 AM - Re: Russian clock with electrical connectors (Jan Mevis)
12. 05:42 AM - Re: Russian clock with electrical connectors (Justin Drafts)
13. 12:35 PM - Re: Russian clock with electrical connectors (Didier Blouzard)
14. 12:40 PM - Re: Russian clock with electrical connectors (Chris & Diane Burton)
15. 03:28 PM - Re: Russian clock with electrical connectors (Al Pickering)
16. 06:24 PM - Re: Russian clock with electrical connectors (Justin Drafts)
17. 11:08 PM - Re: Russian clock with electrical connectors (Jan Mevis)
18. 11:38 PM - Re: Russian clock with electrical connectors (Chris & Diane Burton)
19. 11:54 PM - Re: Russian clock with electrical connectors (Jan Mevis)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: "Battery On" light rear cockpit |
Presume you're describing the -52 REAR annunciator panel 'Battery On' green light
... being a training aircraft this just informs the rear seat instructor that
the front seat student has the master power switch turned on.
Hence it should be on the whole time you're operational, if you don't see it illuminated
then that's the time to be concerned.
It's one of those hidden in plain sight lights, the ones you never notice till
something else is 'off-normal' :-)
Only other annunciator green lights (replicated in both cockpits) are for the Stall
Warning Heat On (if fitted) and Pitot Heat On - self-explanatory as to their
function.
Rob R.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=460921#460921
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Russian clock with electrical connectors |
I had to remove the clock from my Yak 50 for repair.
Then I noticed that it has two connectors for +27 v on the backside (as
stated on the clock).
This is obviously not used on the Yak 50.
Does anyone know what the purpose is?
Regards,
Jan
Yak 50
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Light or de icing?
2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
> I had to remove the clock from my Yak 50 for repair.
> Then I noticed that it has two connectors for +27 v on the backside (as
> stated on the clock).
> This is obviously not used on the Yak 50.
> Does anyone know what the purpose is?
>
> Regards,
>
> Jan
> Yak 50
>
--
____________________________
Didier BLOUZARD
Directeur G=C3=A9n=C3=A9ral DATEXIS
Portable : +33 6 51 84 48 02
Email: didier.blouzard@gmail.com <didier.blouzard@anolistech.fr>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Same clock is sitting on my desk in my boffice right in front of me, indeed
two connectors
27v
2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
> I had to remove the clock from my Yak 50 for repair.
> Then I noticed that it has two connectors for +27 v on the backside (as
> stated on the clock).
> This is obviously not used on the Yak 50.
> Does anyone know what the purpose is?
>
> Regards,
>
> Jan
> Yak 50
>
--
____________________________
Didier BLOUZARD
Directeur G=C3=A9n=C3=A9ral DATEXIS
Portable : +33 6 51 84 48 02
Email: didier.blouzard@gmail.com <didier.blouzard@anolistech.fr>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
If I remember correctly, the Russian clocks were connected to the pitot hea
t circuit.=C2- Thus if pitot heat was turned on, the internal clock heate
r was turned on as well.Dennis
From: Didier Blouzard <didier.blouzard@gmail.com>
To: "yak-list@matronics.com" <yak-list@matronics.com>
Sent: Tuesday, October 4, 2016 7:11 AM
Subject: Re: Yak-List: Russian clock with electrical connectors
Same clock is sitting on my desk in my boffice right in front of me, indeed
two connectors=C2-27v
2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
I had to remove the clock from my Yak 50 for repair.=C2-Then I noticed th
at it has two connectors for +27 v on the backside (as stated on the clock)
.This is obviously not used on the Yak 50.Does anyone know what the purpose
is?=C2-
Regards,
JanYak 50
--
____________________________
Didier BLOUZARD
Directeur G=C3=A9n=C3=A9ral DATEXIS
Portable : +33 6 51 84 48 02
Email: didier.blouzard@gmail.com
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Yes, indeed internal heating for the clock.
Vic
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=460927#460927
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Yes, that seems a very plausible explanation.
Anyway, as far as I know, not used on the 50 (not on mine for certain)
although we also have a pitot heater.
Jan
From: <owner-yak-list-server@matronics.com> on behalf of "A. Dennis
Savarese" <dsavarese0812@bellsouth.net>
Subject: Re: Yak-List: Russian clock with electrical connectors
If I remember correctly, the Russian clocks were connected to the pitot hea
t
circuit. Thus if pitot heat was turned on, the internal clock heater was
turned on as well.
Dennis
From: Didier Blouzard <didier.blouzard@gmail.com>
To: "yak-list@matronics.com" <yak-list@matronics.com>
Sent: Tuesday, October 4, 2016 7:11 AM
Subject: Re: Yak-List: Russian clock with electrical connectors
Same clock is sitting on my desk in my boffice right in front of me, indeed
two connectors
27v
2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
> I had to remove the clock from my Yak 50 for repair.
> Then I noticed that it has two connectors for +27 v on the backside (as s
tated
> on the clock).
> This is obviously not used on the Yak 50.
> Does anyone know what the purpose is?
>
> Regards,
>
> Jan
> Yak 50
--
____________________________
Didier BLOUZARD
Directeur G=E9n=E9ral DATEXIS
Portable : +33 6 51 84 48 02
Email: didier.blouzard@gmail.com <mailto:didier.blouzard@anolistech.fr>
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
It was for heating the clock to maintain a constant temperature so that the c
lock was more accurate George Coy
Sent from my iPad
> On Oct 4, 2016, at 7:10 AM, Didier Blouzard <didier.blouzard@gmail.com> wr
ote:
>
> Light or de icing?
>
> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>> I had to remove the clock from my Yak 50 for repair.
>> Then I noticed that it has two connectors for +27 v on the backside (as s
tated on the clock).
>> This is obviously not used on the Yak 50.
>> Does anyone know what the purpose is?
>>
>> Regards,
>>
>> Jan
>> Yak 50
>
>
>
> --
> ____________________________
> Didier BLOUZARD
> Directeur G=C3=A9n=C3=A9ral DATEXIS
> Portable : +33 6 51 84 48 02
> Email: didier.blouzard@gmail.com
Message 9
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Jan you must realize that the Russians pretty much use that clock and everyt
hing that flies from your Yak 50 to spacecraft so I did a lot of different d
uties. Being electrically heated was critical and some of those duties Georg
e
Sent from my iPad
> On Oct 4, 2016, at 7:51 AM, Jan Mevis <jan.mevis@informavia.be> wrote:
>
> Yes, that seems a very plausible explanation.
> Anyway, as far as I know, not used on the 50 (not on mine for certain) alt
hough we also have a pitot heater.
>
> Jan
>
> From: <owner-yak-list-server@matronics.com> on behalf of "A. Dennis Savare
se" <dsavarese0812@bellsouth.net>
> Date: Tuesday 4 October 2016 at 13:37
> To: "yak-list@matronics.com" <yak-list@matronics.com>
> Subject: Re: Yak-List: Russian clock with electrical connectors
>
> If I remember correctly, the Russian clocks were connected to the pitot he
at circuit. Thus if pitot heat was turned on, the internal clock heater was
turned on as well.
> Dennis
>
>
> From: Didier Blouzard <didier.blouzard@gmail.com>
> To: "yak-list@matronics.com" <yak-list@matronics.com>
> Sent: Tuesday, October 4, 2016 7:11 AM
> Subject: Re: Yak-List: Russian clock with electrical connectors
>
> Same clock is sitting on my desk in my boffice right in front of me, indee
d two connectors
> 27v
>
> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
> I had to remove the clock from my Yak 50 for repair.
> Then I noticed that it has two connectors for +27 v on the backside (as st
ated on the clock).
> This is obviously not used on the Yak 50.
> Does anyone know what the purpose is?
>
> Regards,
>
> Jan
> Yak 50
>
>
>
> --
> ____________________________
> Didier BLOUZARD
> Directeur G=C3=A9n=C3=A9ral DATEXIS
> Portable : +33 6 51 84 48 02
> Email: didier.blouzard@gmail.com
>
>
Message 10
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Russian clock with electrical connectors |
Yes, that is absolutely correct. What puzzles me is that although
beautifully made, these clocks are not that accurate, and, given that, I
wonder whether keeping them warm makes any significant difference!
Richard Goode
From: owner-yak-list-server@matronics.com
[mailto:owner-yak-list-server@matronics.com] On Behalf Of A. Dennis
Savarese
Sent: 04 October 2016 12:38
Subject: Re: Yak-List: Russian clock with electrical connectors
If I remember correctly, the Russian clocks were connected to the pitot
heat circuit. Thus if pitot heat was turned on, the internal clock
heater was turned on as well.
Dennis
_____
From: Didier Blouzard <didier.blouzard@gmail.com
<mailto:didier.blouzard@gmail.com> >
<yak-list@matronics.com <mailto:yak-list@matronics.com> >
Sent: Tuesday, October 4, 2016 7:11 AM
Subject: Re: Yak-List: Russian clock with electrical connectors
Same clock is sitting on my desk in my boffice right in front of me,
indeed two connectors
27v
2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be
<mailto:jan.mevis@informavia.be> >:
I had to remove the clock from my Yak 50 for repair.
Then I noticed that it has two connectors for +27 v on the backside (as
stated on the clock).
This is obviously not used on the Yak 50.
Does anyone know what the purpose is?
Regards,
Jan
Yak 50
--
____________________________
Didier BLOUZARD
Directeur G=C3=A9n=C3=A9ral DATEXIS
Portable : +33 6 51 84 48 02
Email: didier.blouzard@gmail.com <mailto:didier.blouzard@anolistech.fr>
--
This message has been scanned for viruses and
dangerous content by <http://www.mailscanner.info/> MailScanner, and is
believed to be clean.
Message 11
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Thanks, that also explains why it=B9s not necessary on a Yak 50.
Jan
From: <owner-yak-list-server@matronics.com> on behalf of George Coy
<george.coy@gmail.com>
Subject: Re: Yak-List: Russian clock with electrical connectors
It was for heating the clock to maintain a constant temperature so that the
clock was more accurate George Coy
Sent from my iPad
On Oct 4, 2016, at 7:10 AM, Didier Blouzard <didier.blouzard@gmail.com>
wrote:
> Light or de icing?
>
> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>> I had to remove the clock from my Yak 50 for repair.
>> Then I noticed that it has two connectors for +27 v on the backside (as
>> stated on the clock).
>> This is obviously not used on the Yak 50.
>> Does anyone know what the purpose is?
>>
>> Regards,
>>
>> Jan
>> Yak 50
>
>
>
> --
> ____________________________
> Didier BLOUZARD
> Directeur G=E9n=E9ral DATEXIS
> Portable : +33 6 51 84 48 02
> Email: didier.blouzard@gmail.com <mailto:didier.blouzard@anolistech.fr>
Message 12
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Gents, while we're on the topic, I've never used my CJ6's Soviet clock all
that much. I'm wondering what the red button/knob on the left does? Photo
attached. (I see that depressing it flips a red flag to white in the top
dial...) The silver knob on right is for on/off, but needed for winding by
any chance? Or draws its power from the main a/c bus?
Can anyone give me a quick tutorial on the clock's functions?
Thanks-
Justin/N280NC
On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode <
Richard.goode@russianaeros.com> wrote:
> Yes, that is absolutely correct. What puzzles me is that although
> beautifully made, these clocks are not that accurate, and, given that, I
> wonder whether keeping them warm makes any significant difference!
>
>
> Richard Goode
>
>
> *From:* owner-yak-list-server@matronics.com [mailto:owner-yak-list-server
@
> matronics.com] *On Behalf Of *A. Dennis Savarese
> *Sent:* 04 October 2016 12:38
> *To:* yak-list@matronics.com
> *Subject:* Re: Yak-List: Russian clock with electrical connectors
>
>
> If I remember correctly, the Russian clocks were connected to the pitot
> heat circuit. Thus if pitot heat was turned on, the internal clock heate
r
> was turned on as well.
>
> Dennis
>
>
> ------------------------------
>
> *From:* Didier Blouzard <didier.blouzard@gmail.com>
> *To:* "yak-list@matronics.com" <yak-list@matronics.com>
> *Sent:* Tuesday, October 4, 2016 7:11 AM
> *Subject:* Re: Yak-List: Russian clock with electrical connectors
>
>
> Same clock is sitting on my desk in my boffice right in front of me,
> indeed two connectors
>
> 27v
>
>
> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>
> I had to remove the clock from my Yak 50 for repair.
>
> Then I noticed that it has two connectors for +27 v on the backside (as
> stated on the clock).
>
> This is obviously not used on the Yak 50.
>
> Does anyone know what the purpose is?
>
>
> Regards,
>
>
> Jan
>
> Yak 50
>
>
> --
>
>
> *____________________________Didier BLOUZARDDirecteur G=C3=A9n=C3=A9ral D
ATEXIS*Portable
> : +33 6 51 84 48 02
> Email: didier.blouzard@gmail.com <didier.blouzard@anolistech.fr>
>
>
> --
> This message has been scanned for viruses and
> dangerous content by *MailScanner* <http://www.mailscanner.info/>, and is
> believed to be clean.
>
Message 13
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
I have the notice.
Left is total flight time and setting the time, right is leg time and
stopping the watch.
2016-10-04 14:42 GMT+02:00 Justin Drafts <draftsjust417@gmail.com>:
> Gents, while we're on the topic, I've never used my CJ6's Soviet clock al
l
> that much. I'm wondering what the red button/knob on the left does? Photo
> attached. (I see that depressing it flips a red flag to white in the top
> dial...) The silver knob on right is for on/off, but needed for winding b
y
> any chance? Or draws its power from the main a/c bus?
>
> Can anyone give me a quick tutorial on the clock's functions?
>
> Thanks-
>
> Justin/N280NC
>
> On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode <Richard.goode@russianaeros
.
> com> wrote:
>
>> Yes, that is absolutely correct. What puzzles me is that although
>> beautifully made, these clocks are not that accurate, and, given that, I
>> wonder whether keeping them warm makes any significant difference!
>>
>>
>>
>> Richard Goode
>>
>>
>>
>> *From:* owner-yak-list-server@matronics.com [mailto:
>> owner-yak-list-server@matronics.com] *On Behalf Of *A. Dennis Savarese
>> *Sent:* 04 October 2016 12:38
>> *To:* yak-list@matronics.com
>> *Subject:* Re: Yak-List: Russian clock with electrical connectors
>>
>>
>>
>> If I remember correctly, the Russian clocks were connected to the pitot
>> heat circuit. Thus if pitot heat was turned on, the internal clock heat
er
>> was turned on as well.
>>
>> Dennis
>>
>>
>> ------------------------------
>>
>> *From:* Didier Blouzard <didier.blouzard@gmail.com>
>> *To:* "yak-list@matronics.com" <yak-list@matronics.com>
>> *Sent:* Tuesday, October 4, 2016 7:11 AM
>> *Subject:* Re: Yak-List: Russian clock with electrical connectors
>>
>>
>>
>> Same clock is sitting on my desk in my boffice right in front of me,
>> indeed two connectors
>>
>> 27v
>>
>>
>>
>> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>>
>> I had to remove the clock from my Yak 50 for repair.
>>
>> Then I noticed that it has two connectors for +27 v on the backside (as
>> stated on the clock).
>>
>> This is obviously not used on the Yak 50.
>>
>> Does anyone know what the purpose is?
>>
>>
>>
>> Regards,
>>
>>
>>
>> Jan
>>
>> Yak 50
>>
>>
>>
>>
>>
>> --
>>
>>
>>
>>
>> *____________________________Didier BLOUZARDDirecteur G=C3=A9n=C3=A9ral
DATEXIS*Portable
>> : +33 6 51 84 48 02
>> Email: didier.blouzard@gmail.com <didier.blouzard@anolistech.fr>
>>
>>
>>
>>
>> --
>> This message has been scanned for viruses and
>> dangerous content by *MailScanner* <http://www.mailscanner.info/>, and
>> is
>> believed to be clean.
>>
>
>
--
____________________________
Didier BLOUZARD
Directeur G=C3=A9n=C3=A9ral DATEXIS
Portable : +33 6 51 84 48 02
Email: didier.blouzard@gmail.com <didier.blouzard@anolistech.fr>
Message 14
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
This might help you.
Cheers
Chris
> On 5/10/2016, at 1:42 AM, Justin Drafts <draftsjust417@gmail.com>
wrote:
>
> Gents, while we're on the topic, I've never used my CJ6's Soviet clock
all that much. I'm wondering what the red button/knob on the left does?
Photo attached. (I see that depressing it flips a red flag to white in
the top dial...) The silver knob on right is for on/off, but needed for
winding by any chance? Or draws its power from the main a/c bus?
>
> Can anyone give me a quick tutorial on the clock's functions?
>
> Thanks-
>
> Justin/N280NC
>
> On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode
<Richard.goode@russianaeros.com <mailto:Richard.goode@russianaeros.com>>
wrote:
> Yes, that is absolutely correct. What puzzles me is that although
beautifully made, these clocks are not that accurate, and, given that, I
wonder whether keeping them warm makes any significant difference!
>
>
>
> Richard Goode
>
>
>
> From: owner-yak-list-server@matronics.com
<mailto:owner-yak-list-server@matronics.com>
[mailto:owner-yak-list-server@matronics.com
<mailto:owner-yak-list-server@matronics.com>] On Behalf Of A. Dennis
Savarese
> Sent: 04 October 2016 12:38
> To: yak-list@matronics.com <mailto:yak-list@matronics.com>
> Subject: Re: Yak-List: Russian clock with electrical connectors
>
>
>
> If I remember correctly, the Russian clocks were connected to the
pitot heat circuit. Thus if pitot heat was turned on, the internal
clock heater was turned on as well.
>
> Dennis
>
>
>
> From: Didier Blouzard <didier.blouzard@gmail.com
<mailto:didier.blouzard@gmail.com>>
> To: "yak-list@matronics.com <mailto:yak-list@matronics.com>"
<yak-list@matronics.com <mailto:yak-list@matronics.com>>
> Sent: Tuesday, October 4, 2016 7:11 AM
> Subject: Re: Yak-List: Russian clock with electrical connectors
>
>
>
> Same clock is sitting on my desk in my boffice right in front of me,
indeed two connectors
>
> 27v
>
>
>
> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be
<mailto:jan.mevis@informavia.be>>:
>
> I had to remove the clock from my Yak 50 for repair.
>
> Then I noticed that it has two connectors for +27 v on the backside
(as stated on the clock).
>
> This is obviously not used on the Yak 50.
>
> Does anyone know what the purpose is?
>
>
>
> Regards,
>
>
>
> Jan
>
> Yak 50
>
>
>
>
>
>
> --
>
> ____________________________
> Didier BLOUZARD
> Directeur G=C3=A9n=C3=A9ral DATEXIS
> Portable : +33 6 51 84 48 02 <tel:%2B33%206%2051%2084%2048%2002>
> Email: didier.blouzard@gmail.com
<mailto:didier.blouzard@anolistech.fr>
>
>
>
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner <http://www.mailscanner.info/>, and
is
> believed to be clean.
>
>
> <Soviet clock (1).jpg>
Message 15
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |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Message 16
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Yes thanks gents, all VERY helpful info -
Justin
On Tue, Oct 4, 2016 at 3:40 PM, Chris & Diane Burton <cdoburton@gmail.com>
wrote:
> This might help you.
>
> Cheers
> Chris
>
>
> On 5/10/2016, at 1:42 AM, Justin Drafts <draftsjust417@gmail.com> wrote:
>
> Gents, while we're on the topic, I've never used my CJ6's Soviet clock al
l
> that much. I'm wondering what the red button/knob on the left does? Photo
> attached. (I see that depressing it flips a red flag to white in the top
> dial...) The silver knob on right is for on/off, but needed for winding b
y
> any chance? Or draws its power from the main a/c bus?
>
> Can anyone give me a quick tutorial on the clock's functions?
>
> Thanks-
>
> Justin/N280NC
>
> On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode <Richard.goode@
> russianaeros.com> wrote:
>
>> Yes, that is absolutely correct. What puzzles me is that although
>> beautifully made, these clocks are not that accurate, and, given that, I
>> wonder whether keeping them warm makes any significant difference!
>>
>>
>>
>> Richard Goode
>>
>>
>>
>> *From:* owner-yak-list-server@matronics.com [mailto:owner-yak-
>> list-server@matronics.com] *On Behalf Of *A. Dennis Savarese
>> *Sent:* 04 October 2016 12:38
>> *To:* yak-list@matronics.com
>> *Subject:* Re: Yak-List: Russian clock with electrical connectors
>>
>>
>>
>> If I remember correctly, the Russian clocks were connected to the pitot
>> heat circuit. Thus if pitot heat was turned on, the internal clock heat
er
>> was turned on as well.
>>
>> Dennis
>>
>>
>> ------------------------------
>>
>> *From:* Didier Blouzard <didier.blouzard@gmail.com>
>> *To:* "yak-list@matronics.com" <yak-list@matronics.com>
>> *Sent:* Tuesday, October 4, 2016 7:11 AM
>> *Subject:* Re: Yak-List: Russian clock with electrical connectors
>>
>>
>>
>> Same clock is sitting on my desk in my boffice right in front of me,
>> indeed two connectors
>>
>> 27v
>>
>>
>>
>> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>>
>> I had to remove the clock from my Yak 50 for repair.
>>
>> Then I noticed that it has two connectors for +27 v on the backside (as
>> stated on the clock).
>>
>> This is obviously not used on the Yak 50.
>>
>> Does anyone know what the purpose is?
>>
>>
>>
>> Regards,
>>
>>
>>
>> Jan
>>
>> Yak 50
>>
>>
>>
>>
>>
>> --
>>
>>
>>
>>
>> *____________________________Didier BLOUZARDDirecteur G=C3=A9n=C3=A9ral
DATEXIS*Portable
>> : +33 6 51 84 48 02
>> Email: didier.blouzard@gmail.com <didier.blouzard@anolistech.fr>
>>
>>
>>
>>
>> --
>> This message has been scanned for viruses and
>> dangerous content by *MailScanner* <http://www.mailscanner.info/>, and i
s
>>
>> believed to be clean.
>>
>
> <Soviet clock (1).jpg>
>
>
Message 17
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
Very interesting indeed, thanks to all!
Jan
From: <owner-yak-list-server@matronics.com> on behalf of Justin Drafts
<draftsjust417@gmail.com>
Subject: Re: Yak-List: Russian clock with electrical connectors
Yes thanks gents, all VERY helpful info -
Justin
On Tue, Oct 4, 2016 at 3:40 PM, Chris & Diane Burton <cdoburton@gmail.com>
wrote:
> This might help you=8A.
>
> Cheers
> Chris
>
>
>> On 5/10/2016, at 1:42 AM, Justin Drafts <draftsjust417@gmail.com> wrote:
>>
>> Gents, while we're on the topic, I've never used my CJ6's Soviet clock a
ll
>> that much. I'm wondering what the red button/knob on the left does? Phot
o
>> attached. (I see that depressing it flips a red flag to white in the top
>> dial...) The silver knob on right is for on/off, but needed for winding
by
>> any chance? Or draws its power from the main a/c bus?
>>
>> Can anyone give me a quick tutorial on the clock's functions?
>>
>> Thanks-
>>
>> Justin/N280NC
>>
>> On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode
>> <Richard.goode@russianaeros.com> wrote:
>>> Yes, that is absolutely correct. What puzzles me is that although
>>> beautifully made, these clocks are not that accurate, and, given that,
I
>>> wonder whether keeping them warm makes any significant difference!
>>>
>>> Richard Goode
>>>
>>>
>>> From: owner-yak-list-server@matronics.com
>>> [mailto:owner-yak-list-server@matronics.com] On Behalf Of A. Dennis Sav
arese
>>> Sent: 04 October 2016 12:38
>>> To: yak-list@matronics.com
>>> Subject: Re: Yak-List: Russian clock with electrical connectors
>>>
>>>
>>> If I remember correctly, the Russian clocks were connected to the pitot
heat
>>> circuit. Thus if pitot heat was turned on, the internal clock heater w
as
>>> turned on as well.
>>>
>>> Dennis
>>>
>>>
>>>
>>>
>>> From: Didier Blouzard <didier.blouzard@gmail.com>
>>> To: "yak-list@matronics.com" <yak-list@matronics.com>
>>> Sent: Tuesday, October 4, 2016 7:11 AM
>>> Subject: Re: Yak-List: Russian clock with electrical connectors
>>>
>>>
>>>
>>> Same clock is sitting on my desk in my boffice right in front of me, in
deed
>>> two connectors
>>>
>>> 27v
>>>
>>>
>>>
>>> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>>>>
>>>> I had to remove the clock from my Yak 50 for repair.
>>>>
>>>> Then I noticed that it has two connectors for +27 v on the backside (a
s
>>>> stated on the clock).
>>>>
>>>> This is obviously not used on the Yak 50.
>>>>
>>>> Does anyone know what the purpose is?
>>>>
>>>>
>>>>
>>>> Regards,
>>>>
>>>>
>>>>
>>>> Jan
>>>>
>>>> Yak 50
>>>
>>>
>>>
>>> --
>>>
>>> ____________________________
>>> Didier BLOUZARD
>>> Directeur G=E9n=E9ral DATEXIS
>>> Portable : +33 6 51 84 48 02 <tel:%2B33%206%2051%2084%2048%2002>
>>> Email: didier.blouzard@gmail.com <mailto:didier.blouzard@anolistech.fr>
>>>
>>>
>>> --
>>> This message has been scanned for viruses and
>>> dangerous content by MailScanner <http://www.mailscanner.info/> , and i
s
>>> believed to be clean.
>>
>> <Soviet clock (1).jpg>
>
Message 18
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
I am glad to be able to assist.
I wish I could claim credit for the picture, but I got it off the
internet somewhere.
I have one of these clocks sitting on my desk and while I am a typical
male who can usually stuff it up without printed help, I had to hunt
down some instructions on how to drive the thing.
If the clock is inaccurate, you can also adjust the =98speed=99
by twiddling a screw on the rear.
Chris
> On 5/10/2016, at 7:07 PM, Jan Mevis <jan.mevis@informavia.be> wrote:
>
> Very interesting indeed, thanks to all!
>
> Jan
>
> From: <owner-yak-list-server@matronics.com
<mailto:owner-yak-list-server@matronics.com>> on behalf of Justin Drafts
<draftsjust417@gmail.com <mailto:draftsjust417@gmail.com>>
<yak-list@matronics.com <mailto:yak-list@matronics.com>>
> Date: Wednesday 5 October 2016 at 03:23
> To: "yak-list@matronics.com <mailto:yak-list@matronics.com>"
<yak-list@matronics.com <mailto:yak-list@matronics.com>>
> Subject: Re: Yak-List: Russian clock with electrical connectors
>
> Yes thanks gents, all VERY helpful info -
>
> Justin
>
> On Tue, Oct 4, 2016 at 3:40 PM, Chris & Diane Burton
<cdoburton@gmail.com <mailto:cdoburton@gmail.com>> wrote:
> This might help you.
>
> Cheers
> Chris
>
> <Clock.png>
>
>> On 5/10/2016, at 1:42 AM, Justin Drafts <draftsjust417@gmail.com
<mailto:draftsjust417@gmail.com>> wrote:
>>
>> Gents, while we're on the topic, I've never used my CJ6's Soviet
clock all that much. I'm wondering what the red button/knob on the left
does? Photo attached. (I see that depressing it flips a red flag to
white in the top dial...) The silver knob on right is for on/off, but
needed for winding by any chance? Or draws its power from the main a/c
bus?
>>
>> Can anyone give me a quick tutorial on the clock's functions?
>>
>> Thanks-
>>
>> Justin/N280NC
>>
>> On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode
<Richard.goode@russianaeros.com <mailto:Richard.goode@russianaeros.com>>
wrote:
>> Yes, that is absolutely correct. What puzzles me is that although
beautifully made, these clocks are not that accurate, and, given that, I
wonder whether keeping them warm makes any significant difference!
>>
>>
>>
>> Richard Goode
>>
>>
>>
>> From: owner-yak-list-server@matronics.com
<mailto:owner-yak-list-server@matronics.com>
[mailto:owner-yak-list-server@matronics.com
<mailto:owner-yak-list-server@matronics.com>] On Behalf Of A. Dennis
Savarese
>> Sent: 04 October 2016 12:38
>> To: yak-list@matronics.com <mailto:yak-list@matronics.com>
>> Subject: Re: Yak-List: Russian clock with electrical connectors
>>
>>
>>
>> If I remember correctly, the Russian clocks were connected to the
pitot heat circuit. Thus if pitot heat was turned on, the internal
clock heater was turned on as well.
>>
>> Dennis
>>
>>
>>
>> From: Didier Blouzard <didier.blouzard@gmail.com
<mailto:didier.blouzard@gmail.com>>
>> To: "yak-list@matronics.com <mailto:yak-list@matronics.com>"
<yak-list@matronics.com <mailto:yak-list@matronics.com>>
>> Sent: Tuesday, October 4, 2016 7:11 AM
>> Subject: Re: Yak-List: Russian clock with electrical connectors
>>
>>
>>
>> Same clock is sitting on my desk in my boffice right in front of me,
indeed two connectors
>>
>> 27v
>>
>>
>>
>> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be
<mailto:jan.mevis@informavia.be>>:
>>
>> I had to remove the clock from my Yak 50 for repair.
>>
>> Then I noticed that it has two connectors for +27 v on the backside
(as stated on the clock).
>>
>> This is obviously not used on the Yak 50.
>>
>> Does anyone know what the purpose is?
>>
>>
>>
>> Regards,
>>
>>
>>
>> Jan
>>
>> Yak 50
>>
>>
>>
>>
>>
>>
>> --
>>
>> ____________________________
>> Didier BLOUZARD
>> Directeur G=C3=A9n=C3=A9ral DATEXIS
>> Portable : +33 6 51 84 48 02 <tel:%2B33%206%2051%2084%2048%2002>
>> Email: didier.blouzard@gmail.com
<mailto:didier.blouzard@anolistech.fr>
>>
>>
>>
>> --
>> This message has been scanned for viruses and
>> dangerous content by MailScanner <http://www.mailscanner.info/>, and
is
>> believed to be clean.
>>
>>
>> <Soviet clock (1).jpg>
>
>
> <Clock.png>
Message 19
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Russian clock with electrical connectors |
I am running mine, after repair, on my desk.
After 24 hours it is still indicates the correct time (to the minute, at
least).
So IMHO, it=B9s more than good enough for use in a 50 or 52.
Though I can imagine that the G-forces while flying or from aerobatics migh
t
influence the accuracy.
Jan
From: <owner-yak-list-server@matronics.com> on behalf of Chris & Diane
Burton <cdoburton@gmail.com>
Subject: Re: Yak-List: Russian clock with electrical connectors
I am glad to be able to assist.
I wish I could claim credit for the picture, but I got it off the internet
somewhere.
I have one of these clocks sitting on my desk and while I am a typical male
who can usually stuff it up without printed help, I had to hunt down some
instructions on how to drive the thing.
If the clock is inaccurate, you can also adjust the =8Cspeed=B9 by twiddling a
screw on the rear.
Chris
> On 5/10/2016, at 7:07 PM, Jan Mevis <jan.mevis@informavia.be> wrote:
>
> Very interesting indeed, thanks to all!
>
> Jan
>
> From: <owner-yak-list-server@matronics.com> on behalf of Justin Drafts
> <draftsjust417@gmail.com>
> Date: Wednesday 5 October 2016 at 03:23
> To: "yak-list@matronics.com" <yak-list@matronics.com>
> Subject: Re: Yak-List: Russian clock with electrical connectors
>
> Yes thanks gents, all VERY helpful info -
>
> Justin
>
> On Tue, Oct 4, 2016 at 3:40 PM, Chris & Diane Burton <cdoburton@gmail.com
>
> wrote:
>> This might help you=8A.
>>
>> Cheers
>> Chris
>>
>> <Clock.png>
>>
>>> On 5/10/2016, at 1:42 AM, Justin Drafts <draftsjust417@gmail.com> wrote
:
>>>
>>> Gents, while we're on the topic, I've never used my CJ6's Soviet clock
all
>>> that much. I'm wondering what the red button/knob on the left does? Pho
to
>>> attached. (I see that depressing it flips a red flag to white in the to
p
>>> dial...) The silver knob on right is for on/off, but needed for winding
by
>>> any chance? Or draws its power from the main a/c bus?
>>>
>>> Can anyone give me a quick tutorial on the clock's functions?
>>>
>>> Thanks-
>>>
>>> Justin/N280NC
>>>
>>> On Tue, Oct 4, 2016 at 8:10 AM, Richard Goode
>>> <Richard.goode@russianaeros.com> wrote:
>>>> Yes, that is absolutely correct. What puzzles me is that although
>>>> beautifully made, these clocks are not that accurate, and, given that,
I
>>>> wonder whether keeping them warm makes any significant difference!
>>>>
>>>> Richard Goode
>>>>
>>>>
>>>> From: owner-yak-list-server@matronics.com
>>>> [mailto:owner-yak-list-server@matronics.com] On Behalf Of A. Dennis
>>>> Savarese
>>>> Sent: 04 October 2016 12:38
>>>> To: yak-list@matronics.com
>>>> Subject: Re: Yak-List: Russian clock with electrical connectors
>>>>
>>>>
>>>> If I remember correctly, the Russian clocks were connected to the pito
t
>>>> heat circuit. Thus if pitot heat was turned on, the internal clock he
ater
>>>> was turned on as well.
>>>>
>>>> Dennis
>>>>
>>>>
>>>>
>>>>
>>>> From: Didier Blouzard <didier.blouzard@gmail.com>
>>>> To: "yak-list@matronics.com" <yak-list@matronics.com>
>>>> Sent: Tuesday, October 4, 2016 7:11 AM
>>>> Subject: Re: Yak-List: Russian clock with electrical connectors
>>>>
>>>>
>>>>
>>>> Same clock is sitting on my desk in my boffice right in front of me, i
ndeed
>>>> two connectors
>>>>
>>>> 27v
>>>>
>>>>
>>>>
>>>> 2016-10-04 13:05 GMT+02:00 Jan Mevis <jan.mevis@informavia.be>:
>>>>>
>>>>> I had to remove the clock from my Yak 50 for repair.
>>>>>
>>>>> Then I noticed that it has two connectors for +27 v on the backside (
as
>>>>> stated on the clock).
>>>>>
>>>>> This is obviously not used on the Yak 50.
>>>>>
>>>>> Does anyone know what the purpose is?
>>>>>
>>>>>
>>>>>
>>>>> Regards,
>>>>>
>>>>>
>>>>>
>>>>> Jan
>>>>>
>>>>> Yak 50
>>>>
>>>>
>>>>
>>>> --
>>>>
>>>> ____________________________
>>>> Didier BLOUZARD
>>>> Directeur G=E9n=E9ral DATEXIS
>>>> Portable : +33 6 51 84 48 02 <tel:%2B33%206%2051%2084%2048%2002>
>>>> Email: didier.blouzard@gmail.com <mailto:didier.blouzard@anolistech.fr
>
>>>>
>>>>
>>>> --
>>>> This message has been scanned for viruses and
>>>> dangerous content by MailScanner <http://www.mailscanner.info/> , and
is
>>>> believed to be clean.
>>>
>>> <Soviet clock (1).jpg>
>>
>
> <Clock.png>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|