---------------------------------------------------------- Yak-List Digest Archive --- Total Messages Posted Thu 05/04/17: 7 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:02 AM - Re: HS 6 FAILURE (woodja51) 2. 07:53 AM - Re: Re: HS 6 FAILURE (Roger Kemp) 3. 12:05 PM - Russian Log Translation (Bill1200) 4. 01:05 PM - Re: Russian Log Translation (Looigi) 5. 02:36 PM - Re: Russian Log Translation (JON) 6. 09:30 PM - Re: Russian Log Translation (Looigi) 7. 10:21 PM - Re: HS 6 FAILURE (woodja51) ________________________________ Message 1 _____________________________________ Time: 03:02:31 AM PST US Subject: Yak-List: Re: HS 6 FAILURE From: "woodja51" Does any one know if the rear accessory case simply comes away from the intermediate case on a HS6 , or does it have to be pulled down / aft securing bolt removed to detach it ? The manuals indicate the drive shaft for the accessories might slide over the end of the crankshaft output and not rigidly fixed - allowing removal in one piece ? Or... not ! Still working on finding out what let go inside mine ... have found some larger chunks of non ferrous bits when looking down a few intake tubes .. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=468957#468957 ________________________________ Message 2 _____________________________________ Time: 07:53:14 AM PST US Subject: Re: Yak-List: Re: HS 6 FAILURE From: Roger Kemp If it is like the M14, it a spline drive. Crack the case and slide straight apart. Doc Sent from my iPad > On May 4, 2017, at 4:59 AM, woodja51 wrote: > > > Does any one know if the rear accessory case simply comes away from the intermediate case on a HS6 , or does it have to be pulled down / aft securing bolt removed to detach it ? The manuals indicate the drive shaft for the accessories might slide over the end of the crankshaft output and not rigidly fixed - allowing removal in one piece ? Or... not ! > > Still working on finding out what let go inside mine ... have found some larger chunks of non ferrous bits when looking down a few intake tubes .. > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=468957#468957 > > > > > > > > > ________________________________ Message 3 _____________________________________ Time: 12:05:52 PM PST US Subject: Yak-List: Russian Log Translation From: "Bill1200" Looking for a resource to translate Russian engine logs Thanks, Bill Read this topic online here: http://forums.matronics.com/viewtopic.php?p=468989#468989 ________________________________ Message 4 _____________________________________ Time: 01:05:55 PM PST US Subject: Yak-List: Re: Russian Log Translation From: "Looigi" Hi Bill, I have a friend who has just translated my Russian Logbooks for me. I can ask her or you if you like? You would need to either post them over, or scan and email them to her I guess. We are in New Zealand, so not just next door! Cheers Chris Read this topic online here: http://forums.matronics.com/viewtopic.php?p=468993#468993 ________________________________ Message 5 _____________________________________ Time: 02:36:32 PM PST US From: JON Subject: Re: Yak-List: Russian Log Translation You might try these sites or there are many other if=C2-you can't find a human to do it.=C2- JB http://mashke.org/Conv/ =C2- http://www.lexilogos.com/keyboard/russian_conversion.htm ----- Original Message ----- From: "Bill1200" Sent: Thursday, May 4, 2017 2:03:34 PM Subject: Yak-List: Russian Log Translation Looking for a resource to translate Russian engine logs Thanks, Bill Read this topic online here: http://forums.matronics.com/viewtopic.php?p=468989#468989 =========== =========== MS - =========== WIKI - =========== e - =C2- =C2- =C2- =C2- =C2--Matt Dralle, List Admin. =========== ________________________________ Message 6 _____________________________________ Time: 09:30:10 PM PST US Subject: Yak-List: Re: Russian Log Translation From: "Looigi" Yep, I tried those sites too. They are probably quite good for general day to day translation, but they struggle with the more technical writings. The result of one attempt reminded me of Monty Python... https://www.youtube.com/watch?v=2YYM209GJoE Read this topic online here: http://forums.matronics.com/viewtopic.php?p=469008#469008 ________________________________ Message 7 _____________________________________ Time: 10:21:00 PM PST US Subject: Yak-List: Re: HS 6 FAILURE From: "woodja51" Thanks ! That sounds like a good design concept for ease of replacement.! Also. How hard is cylinder over haul ( just lapping valve seats and honing - to hopefully restore the valve sealing after the fine particles from the supercharger got in there ... Read this topic online here: http://forums.matronics.com/viewtopic.php?p=469011#469011 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message yak-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Yak-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/yak-list Browse Digests http://www.matronics.com/digest/yak-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.