Today's Message Index:
----------------------
1. 03:37 AM - Certification Categories (Craig Payne)
2. 05:52 AM - Generator noise (Garry Pope)
3. 11:35 AM - Re: Re: Yak 18T Jacks (Taylor)
4. 12:23 PM - Re: Re: Yak 18T Jacks (Chris & Diane Burton)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Certification Categories |
The categories I'm familiar with within the Standard are:
*Normal*, good for maneuvers up to +3.8/-1.52
*Utility*, +4.4/-1.76
*Acrobatic*, +6.0/-3.0
That would put the CJ-6 in the Acrobatic category at 3086 lbs, more for the
Utility and forget about the Normal since it is the maneuvering and speed
loads that dictate the the ratings described in 23.3. Thus operating a CJ-6
at weights above 3086 requires lower G loads to stay in the "envelope".
Craig Payne
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I recently started having static interference in my King radio, after installing
Denniss auto harness. After about 6 months static free, static has started sometimes
in the air, but continuously on the ground. I am assuming it is the generator,
as the noise increases and decreases with RPM. Its strange that in the
air it only happens sometimes, not consistent.
Ive heard others have had this issue in the past and want to know what resistor
they used on the mags to resolve it. No sense trying to figure out if there is
already a solution.
Your help is appreciated!
Garry Pope
Sent from my iPhone
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Yak 18T Jacks |
Hi all
If the yak owner still needs factory jacks Ive got a set in my hangar
Pete Taylor
530-200-0144
Sent from my iPad
> On Oct 4, 2017, at 9:04 PM, weloveflying <yourordinarybeing@gmail.com> wrote:
>
>
> Have you tried getting parts from companies which offer metal machining services, like this one (http://www.powerjackmotion.com/product-category/metal-maching-service/) for example? The said company has lift systems as one of their specialties, but most of these are for automation or motion control; however, they also offer metal machining services which, I think, you can leverage to get a jack made for you according to your desired measurement.
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=473358#473358
>
>
>
>
>
>
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Yak 18T Jacks |
Hi Pete,
Can you please take some pictures of the jacks please? I am gearing up to make
some.
Kind regards
Chris
Sent from my iPhone, so typo's are bought to you courtesy of Siri.
> On 7/10/2017, at 07:34, Taylor <taylor527@att.net> wrote:
>
>
> Hi all
> If the yak owner still needs factory jacks Ive got a set in my hangar
> Pete Taylor
> 530-200-0144
>
> Sent from my iPad
>
>> On Oct 4, 2017, at 9:04 PM, weloveflying <yourordinarybeing@gmail.com> wrote:
>>
>>
>> Have you tried getting parts from companies which offer metal machining services, like this one (http://www.powerjackmotion.com/product-category/metal-maching-service/) for example? The said company has lift systems as one of their specialties, but most of these are for automation or motion control; however, they also offer metal machining services which, I think, you can leverage to get a jack made for you according to your desired measurement.
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=473358#473358
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|