Today's Message Index:
----------------------
 
     1. 06:22 PM - CJ Prop Blade Angle Procedure (PS)
     2. 10:46 PM - Re: CJ Prop Blade Angle Procedure (Walter Lannon)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:22:10 PM PST US
Subject: 
CJ Prop Blade Angle Procedure
From: 
"PS" <psalter@aol.com>
      
      
      I have been fighting setting blade angles for my Housai powered CJ since last Friday.
      I do not understand where to measure the angle. I tried 1000mm from the
      prop oil supply tube and I tried 8 from the blade tip. What is correct? I am
      curious if the governor is set incorrectly. 
      
      Phil
      
      --------
      Phil
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=481431#481431
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
10:46:56 PM PST US
From: 
"Walter Lannon" <wlannon@shaw.ca>
Subject: 
Re: CJ Prop Blade Angle Procedure
      
      
      Hi Phil;
      
      1000 mm from the C/L is correct but if you just want to check that the 
      blades are correctly set check the scribe mark and the scale at the blade 
      grip.  The scribe mark should be at the center mark.  If they both look the 
      same and you have no issues with vibration, etc. sit down and have a beer or 
      two.
      
      If you suspect a governor issue run through the governor setting procedure 
      in the manual and make sure there are no loose control system bolts or 
      clamps etc. allowing the cable housing to move.
      
      Cheers;
      Walt
      
      -----Original Message----- 
      From: PS
      Sent: Thursday, July 05, 2018 6:21 PM
      Subject: Yak-List: CJ Prop Blade Angle Procedure
      
      
      I have been fighting setting blade angles for my Housai powered CJ since 
      last Friday. I do not understand where to measure the angle. I tried 1000mm 
      from the prop oil supply tube and I tried 8 from the blade tip. What is 
      correct? I am curious if the governor is set incorrectly.
      
      Phil
      
      --------
      Phil
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=481431#481431
      
      
      ---
      This email has been checked for viruses by Avast antivirus software.
      https://www.avast.com/antivirus
      
      








Other Matronics Email List Services




Post A New Message
  
yak-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Yak-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/yak-list
Browse Yak-List Digests
  
http://www.matronics.com/digest/yak-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --