----------------------------------------------------------
                           Yak-List Digest Archive
                                      ---
                     Total Messages Posted Thu 08/30/18: 2
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 04:56 AM - Re: Intake tubage  (A. Dennis Savarese)
     2. 10:32 AM - Re: Re: Yak Air Valves  (Roger Kemp)
 
 
 
________________________________  Message 1  _____________________________________


Time: 04:56:21 AM PST US
From: "A. Dennis Savarese" <dsavarese0812@bellsouth.net>
Subject: Re: Yak-List: Intake tubage

Typically, I place the rubber seal on the tube and work it into the case.
=C2- You may try first coating the outside of the seal, after it is on th
e intake tube, with a very light coat of fuel lube to help it slide into pl
ace.=C2- Or put a light coat of fuel lube on the inside of the hole in th
e case.=C2- The difficulty (as you know) is getting the first threads on 
the collar to "bite" because the rubber seal is not seated deep enough into
 the hole.=C2- A few times I have had to push the seal into position afte
r the the tube is in place using a plastic tool, which I fabricated from th
e handle of an old tooth brush.=C2- 
Dennis

      From: Jon Boede <jonboede@hotmail.com>
 To: "yak-list@matronics.com" <yak-list@matronics.com> 
 Sent: Thursday, August 30, 2018 1:31 AM
 Subject: Yak-List: Intake tubage
   

Swap the carb - easy peasy. 

Get the #5 intake tube to go back in - %#$&@!!

Anybody have a trick they want to share? Does the tube go in first and you 
work the rubber ring in after, or is (supposedly) easier to start with the 
rubber ring at the top of the tube and slide the tube in through it?

Jon
S -
WIKI -
 -
=C2- =C2- =C2- =C2- =C2- -Matt Dralle, List Admin.


   

________________________________  Message 2  _____________________________________


Time: 10:32:57 AM PST US
From: Roger Kemp <f16viperdoc@me.com>
Subject: Re: Yak-List: Re: Yak Air Valves


True. Where did you find the square O rings.
Doc

Sent from my iPad

> On Aug 29, 2018, at 5:17 PM, LawnDart <propwash@gmail.com> wrote:
> 
> 
> In almost 20 years, the only leaks I have had on the emergency side were at the
emergency valves in the cockpits.  There is a square o-ring, #6 in the attachment;
this has always been the offender.
> 
> 
> 
> 
> Read this topic online here:
> 
> http://forums.matronics.com/viewtopic.php?p=482782#482782
> 
> 
> 
> 
> Attachments: 
> 
> http://forums.matronics.com//files/e_valve_186.jpg
> 
> 
> 
> 
> 
> 


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               yak-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Yak-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/yak-list
Browse Digests                   http://www.matronics.com/digest/yak-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.