Today's Message Index:
----------------------
1. 11:04 AM - Battery Clamp WTB (fishface68)
2. 06:19 PM - CJ6 Landing Gear Handle Leak (Okanogan Lew)
3. 06:46 PM - Re: CJ6 Landing Gear Handle Leak (wdjester)
4. 08:10 PM - Re: CJ6 Landing Gear Handle Leak (Hank Gibson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Battery Clamp WTB |
Hi All
Does anyone out there have a yak battery clamp that I can buy? I need the two hooked
and threaded rods, the angled cross piece and the washers spacers and wing
nuts. I cannot seen to find one anywhere. I believe that originally most yaks
had two as there are two locating holes in the battery trays but only one
is required for the battery conversion.
Many thanks
Best wishes Pat
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=483379#483379
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | CJ6 Landing Gear Handle Leak |
I noticed air leaking from my front gear handle & replaced it with a new one from
Doug. But, it still leaks in the middle position & in the down position.
It stops when the handle is in the up position. Any thoughts? Thanks in advance.
Paul
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=483389#483389
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 Landing Gear Handle Leak |
As painful as it is to say, you might have a bad rear gear handle.
Sent from my iPad
> On Sep 26, 2018, at 8:18 PM, Okanogan Lew <vplewis@community.org> wrote:
>
>
> I noticed air leaking from my front gear handle & replaced it with a new one
from Doug. But, it still leaks in the middle position & in the down position.
It stops when the handle is in the up position. Any thoughts? Thanks in advance.
>
> Paul
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=483389#483389
>
>
>
>
>
>
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 Landing Gear Handle Leak |
Agree with Jester...Prob bad rear valve. Been there done that. Remove it permanently
and youll solve a big headache. Procedure costs less than $10 and I can
send it to you if interested.
Hoot
hkgibby@yahoo.com
Sent from my iPhone
> On Sep 26, 2018, at 6:46 PM, wdjester <wdjester@cox.net> wrote:
>
>
> As painful as it is to say, you might have a bad rear gear handle.
>
> Sent from my iPad
>
>> On Sep 26, 2018, at 8:18 PM, Okanogan Lew <vplewis@community.org> wrote:
>>
>>
>> I noticed air leaking from my front gear handle & replaced it with a new one
from Doug. But, it still leaks in the middle position & in the down position.
It stops when the handle is in the up position. Any thoughts? Thanks in advance.
>>
>> Paul
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=483389#483389
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|