Today's Message Index:
----------------------
1. 08:05 AM - Re: Re: CJ6 aileron bearings (A. Dennis Savarese)
2. 06:15 PM - Re: Cleaning the engine (Greg Wrobel)
3. 10:40 PM - Re: Re: CJ6 aileron bearings (Stephen van Dijck)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 aileron bearings |
Absolutely!=C2- Make it easy on yourself if you're looking for bearings,
or anything else for CJ's for that matter.=C2- Just call Doug.=C2- He
should clearly your go-to guy.Dennis
On Tuesday, August 25, 2020, 6:57:52 PM EDT, doug sapp <dougsappllc@gma
il.com> wrote:
There are basically two sizes of self aligning bearings used in the CJ.=C2
- I normally have good stock on both.
Doug
On Tue, Aug 25, 2020 at 1:39 PM William Geipel <wamflight@gmail.com> wrote:
typed: =C2-=C2-6x19x6 mm self aligning bearings- into google. Anywhere
from $4 to $26 for the same thing.
On Aug 25, 2020, at 3:07 PM, Anthony Savarese <dsavarese0812@bellsouth.net>
wrote:
et>
The bearings are 6x19x6 mm self aligning bearings. They are available all o
ver the internet. Be sure to include =9Cself aligning bearing
=9D in your search.
Dennis
Sent from my iPhone
On Aug 25, 2020, at 1:18 PM, AlaskaChang801 <themilnes95@gmail.com> wrote:
l.com>
I just replaced my elevator bearings and from what I know they are the same
as the rudder and ailerons. I don't know the spec size, but I can tell you
this! They are the same bearings in the canopy rollers and therefore you c
an buy a set of them fairly cheap from Todd Bohlman, you can find him on Eb
ay as that's where he sells them or search for him on the Red Star Facebook
page.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=497975#497975
Attachments:
http://forums.matronics.com//files/cj_bearings_942.jpg
http://www.matronics.com/Navigator?Yak-List
http://wiki.matronics.com
http://www.matronics.com/contribution
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cleaning the engine |
Did I leave out that I do all this outside in a 20 acre rock quarry using a
robot handling the sprayer and have my aircraft insured for 10 times
what's its worth?? What could possibly go wrong. Hey Houston, we have a
problem. That it, I won't do the cyrogenic stir of the 100LL tank prior to
application.
Details, details, details.
Greg "Clouddog" Wrobel
On Tue, Aug 25, 2020, 23:36 Royden Heays <heaysr@telus.net> wrote:
> That=99s the scariest thing I have read on the list to date
=93 sends shivers
> up my spine.
>
>
> Count yourself very lucky that you, your aircraft and hangar still exist.
>
>
> The a/c maintenance shops who annual my Yak use Varsol =93 a practi
ce which
> I adopt for any DIY cleaning.
>
>
> Be safe and switch to Varsol.
>
>
> Royden
>
>
> *From:* owner-yak-list-server@matronics.com [mailto:
> owner-yak-list-server@matronics.com] *On Behalf Of *Greg Wrobel
> *Sent:* Tuesday, August 25, 2020 9:43 AM
> *To:* yak-list@matronics.com
> *Subject:* Re: Yak-List: Cleaning the engine
>
>
> I use 100LL through a wand that has a pickup tube and use 80-90 psi from
> my compressor that is part if the pickup tube system. Available at Harbor
> Freigh. It melts the grease and evaporates before it hits the ground.
> Water, and solvents can get into electical stuff and creates issues. So f
ar
> no issues with 100LL and have been using it for years. But remember, ther
e
> are a lot of opinions and you will need to listen to them and decide.
>
> Greg "Clouddog" Wrobel
>
>
> On Tue, Aug 25, 2020, 06:36 Justin Drafts <draftsjust417@gmail.com> wrote
:
>
> I've had success with simple stoddard solvent, but that's just me.
>
>
> Justin
>
> N280NC
>
>
> On Tue, Aug 25, 2020 at 7:36 AM 1906 <zmadwolf@gmail.com> wrote:
>
>
> What is the preferred way to clean the engine, specifically
> cylinder/exhaust manifold/sump area? Given the leather/cloth in the area,
> are mineral spirits OK?
>
> Thanks.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=497964#497964
>
>
> ==========
> List" rel="noreferrer" target="_blank">
> http://www.matronics.com/Navigator?Yak-List
> ==========
> FORUMS -
> eferrer" target="_blank">http://forums.matronics.com
> ==========
> WIKI -
> errer" target="_blank">http://wiki.matronics.com
> ==========
> b Site -
> -Matt Dralle, List Admin.
> rel="noreferrer" target="_blank">http://www.matronics.com/contributio
n
> ==========
>
>
> ------------------------------
>
> [image:
> https://secureimages.mcafee.com/common/affiliateImages/mfe/logo.png]
> <https://home.mcafee.com/utm_medium=email&utm_source=link&utm_campaig
n=sig-email&utm_content=emailclient?utm_medium=email&utm_source=lin
k&utm_campaign=sig-email&utm_content=emailclient>
>
> Scanned by McAfee
> <https://home.mcafee.com/utm_medium=email&utm_source=link&utm_campaig
n=sig-email&utm_content=emailclient?utm_medium=email&utm_source=lin
k&utm_campaign=sig-email&utm_content=emailclient>
> and confirmed virus-free.
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CJ6 aileron bearings |
Dennis. Are these the same size bearings for the canopy of a Yak?
Kiwi.
> On 25 Aug 2020, at 22:07, Anthony Savarese <dsavarese0812@bellsouth.net> wrote:
>
>
> The bearings are 6x19x6 mm self aligning bearings. They are available all over
the internet. Be sure to include self aligning bearing in your search.
> Dennis
>
> Sent from my iPhone
>
>> On Aug 25, 2020, at 1:18 PM, AlaskaChang801 <themilnes95@gmail.com> wrote:
>>
>>
>> I just replaced my elevator bearings and from what I know they are the same
as the rudder and ailerons. I don't know the spec size, but I can tell you this!
They are the same bearings in the canopy rollers and therefore you can buy
a set of them fairly cheap from Todd Bohlman, you can find him on Ebay as that's
where he sells them or search for him on the Red Star Facebook page.
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=497975#497975
>>
>>
>>
>>
>> Attachments:
>>
>> http://forums.matronics.com//files/cj_bearings_942.jpg
>>
>>
>>
>>
>>
>>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|