---------------------------------------------------------- Yak-List Digest Archive --- Total Messages Posted Sun 11/01/20: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:11 AM - Matronics List Fund Raiser Postponed During 2020... (Matt Dralle) 2. 02:27 AM - Re: Swagelok (Mark Pennington) 3. 05:56 AM - Re: Swagelok (Hank Gibson) 4. 07:05 AM - Re: Swagelok (Warren Hill) 5. 08:49 AM - Re: Swagelok (Warren Hill) 6. 08:58 AM - Re: Swagelok (Mark Pennington) ________________________________ Message 1 _____________________________________ Time: 12:11:42 AM PST US From: Matt Dralle Subject: Yak-List: Matronics List Fund Raiser Postponed During 2020... Dear Listers, Normally, in November I hold a List Fund Raiser where I ask Listers to make a Contribution to support the operation and upkeep of these List resources. In light of the happenings during this 2020 season, I have decided to postpone the Fund Raiser this year and encourage members to focus on their families and personal needs. I want to thank everyone that has supported the Lists in the past. Despite the uncertain times we're experiencing right now, I want to assure everyone that I fully intend to continue supporting the Lists as I always have; with no anticipated degradation in service levels. Happy Holidays to all my friends around the world! Matt Dralle Matronics List Manager ________________________________ Message 2 _____________________________________ Time: 02:27:27 AM PST US From: Mark Pennington Subject: Re: Yak-List: Swagelok Jay Here is a photo I saved of the snot valve with a swagelock valve. At the time the post did not give a part number. Maybe someone will recognize the valve and share the part number Mark N621 CJ On Sat, Oct 31, 2020 at 8:14 PM Warren Hill wrote: > Both the Chinese adaptors and the Swagelok valves are =85=9B-27 NPT pi pe > thread. > > > On Oct 31, 2020, at 5:01 PM, William Geipel wrote: > > did you tap the new valve? size? > > > On Nov 1, 2020, at 8:53 AM, Warren Hill wrote: > > Here is a picture of my CJ emergency on-off valve with adaptors that > duplicate the original line positions. The Yak-52 probably requires > different adaptors. The black handle valve for the main air is Swagelok > part number SS-42GF2-A-WN2 and the emergency air red handle part number i s > SS-42GF2-A-RD-WN2. I suggest placing about 4 turns of nylon tape on the > threads to lessen the likelihood of leaks. Replace and forget. > > Warren Hill > N464TW > Mesa, AZ > > > > > On Oct 31, 2020, at 4:24 PM, jay-dub wrote: > > > Please could someone tell me the spec of the Swagelok valves to replace > the normal and emergency air valves. > > Also, the snot valves. > > Thanks from Lockdown, UK. [Rolling Eyes] > > -------- > CJ and Yak-52 owner > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=499045#499045 > > ________________________________ Message 3 _____________________________________ Time: 05:56:14 AM PST US From: Hank Gibson Subject: Re: Yak-List: Swagelok See RPA Library...click on CJ-6 Nanchang; it=99s there. Sent from my iPhone > On Nov 1, 2020, at 2:40 AM, Mark Pennington wrote: > > =EF=BB > Jay > > Here is a photo I saved of the snot valve with a swagelock valve. > > At the time the post did not give a part number. > > Maybe someone will recognize the valve and share the part number > > Mark > N621 CJ > > > > >> On Sat, Oct 31, 2020 at 8:14 PM Warren Hill wrote: >> Both the Chinese adaptors and the Swagelok valves are =85=9B-27 NPT pi pe thread. >> >> >>> On Oct 31, 2020, at 5:01 PM, William Geipel wrote: >>> >>> did you tap the new valve? size? >>> >>> >>>> On Nov 1, 2020, at 8:53 AM, Warren Hill wrote: >>>> >>>> Here is a picture of my CJ emergency on-off valve with adaptors that du plicate the original line positions. The Yak-52 probably requires different a daptors. The black handle valve for the main air is Swagelok part number SS- 42GF2-A-WN2 and the emergency air red handle part number is SS-42GF2-A-RD-WN 2. I suggest placing about 4 turns of nylon tape on the threads to lessen th e likelihood of leaks. Replace and forget. >>>> >>>> Warren Hill >>>> N464TW >>>> Mesa, AZ >>>> >>>> >>>> >>>> >>>>> On Oct 31, 2020, at 4:24 PM, jay-dub wrote: >>>>> >>>>> >>>>> Please could someone tell me the spec of the Swagelok valves to replac e the normal and emergency air valves. >>>>> >>>>> Also, the snot valves. >>>>> >>>>> Thanks from Lockdown, UK. [Rolling Eyes] >>>>> >>>>> -------- >>>>> CJ and Yak-52 owner >>>>> >>>>> >>>>> >>>>> >>>>> Read this topic online here: >>>>> >>>>> http://forums.matronics.com/viewtopic.php?p=499045#499045 >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>> >>> >> ________________________________ Message 4 _____________________________________ Time: 07:05:49 AM PST US From: Warren Hill Subject: Re: Yak-List: Swagelok Hello Mark, For the Yak-52, it's the Swagelok SS-43GM4-S4. For the CJ, a typical install requires a right angle adaptor and a different right angle Swagelok valve. If you need this part number I=99ll get it later today. Attached are some images. Warren N464TW > On Nov 1, 2020, at 3:26 AM, Mark Pennington wrote: > > Jay > > Here is a photo I saved of the snot valve with a swagelock valve. > > At the time the post did not give a part number. > > Maybe someone will recognize the valve and share the part number > > Mark > N621 CJ > > > > > On Sat, Oct 31, 2020 at 8:14 PM Warren Hill > wrote: > Both the Chinese adaptors and the Swagelok valves are =85=9B-27 NPT pipe thread. > > >> On Oct 31, 2020, at 5:01 PM, William Geipel > wrote: >> >> did you tap the new valve? size? >> >> >>> On Nov 1, 2020, at 8:53 AM, Warren Hill > wrote: >>> >>> Here is a picture of my CJ emergency on-off valve with adaptors that duplicate the original line positions. The Yak-52 probably requires different adaptors. The black handle valve for the main air is Swagelok part number SS-42GF2-A-WN2 and the emergency air red handle part number is SS-42GF2-A-RD-WN2. I suggest placing about 4 turns of nylon tape on the threads to lessen the likelihood of leaks. Replace and forget. >>> >>> Warren Hill >>> N464TW >>> Mesa, AZ >>> >>> >>> >>> >>>> On Oct 31, 2020, at 4:24 PM, jay-dub > wrote: >>>> > >>>> >>>> Please could someone tell me the spec of the Swagelok valves to replace the normal and emergency air valves. >>>> >>>> Also, the snot valves. >>>> >>>> Thanks from Lockdown, UK. [Rolling Eyes] >>>> >>>> -------- >>>> CJ and Yak-52 owner >>>> >>>> >>>> >>>> >>>> Read this topic online here: >>>> >>>> http://forums.matronics.com/viewtopic.php?p=499045#499045 >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>> >> > ________________________________ Message 5 _____________________________________ Time: 08:49:23 AM PST US From: Warren Hill Subject: Re: Yak-List: Swagelok One additional item. If not already done. The bottom thread of the snot bottle will need to be tapped to accept the input side of the Swagelock valve, which I believe is =C2=BC-inch NPT. After completing the tap, be sure to completely wash out the many small metal fragments produced. It=99s helpful to do the tap a little less than you think is needed and then screw int the Swagelock valve until it is tight. If a =C2=BC to =C2=BD turn more is needed to properly align the value, run the tap just a little more. This way the final valve position will not end up at some odd angle. - - - - - - - - - - Hello Mark, For the Yak-52, it's the Swagelok SS-43GM4-S4. For the CJ, a typical install requires a right angle adaptor and a different right angle Swagelok valve. If you need this part number I=99ll get it later today. Attached are some images. Warren N464TW > On Nov 1, 2020, at 3:26 AM, Mark Pennington > wrote: > > Jay > > Here is a photo I saved of the snot valve with a swagelock valve. > > At the time the post did not give a part number. > > Maybe someone will recognize the valve and share the part number > > Mark > N621 CJ > > > > > On Sat, Oct 31, 2020 at 8:14 PM Warren Hill > wrote: > Both the Chinese adaptors and the Swagelok valves are =85=9B-27 NPT pipe thread. > > >> On Oct 31, 2020, at 5:01 PM, William Geipel > wrote: >> >> did you tap the new valve? size? >> >> >>> On Nov 1, 2020, at 8:53 AM, Warren Hill > wrote: >>> >>> Here is a picture of my CJ emergency on-off valve with adaptors that duplicate the original line positions. The Yak-52 probably requires different adaptors. The black handle valve for the main air is Swagelok part number SS-42GF2-A-WN2 and the emergency air red handle part number is SS-42GF2-A-RD-WN2. I suggest placing about 4 turns of nylon tape on the threads to lessen the likelihood of leaks. Replace and forget. >>> >>> Warren Hill >>> N464TW >>> Mesa, AZ >>> >>> >>> >>> >>>> On Oct 31, 2020, at 4:24 PM, jay-dub > wrote: >>>> > >>>> >>>> Please could someone tell me the spec of the Swagelok valves to replace the normal and emergency air valves. >>>> >>>> Also, the snot valves. >>>> >>>> Thanks from Lockdown, UK. [Rolling Eyes] >>>> >>>> -------- >>>> CJ and Yak-52 owner >>>> >>>> >>>> >>>> >>>> Read this topic online here: >>>> >>>> http://forums.matronics.com/viewtopic.php?p=499045#499045 >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>> >> > ________________________________ Message 6 _____________________________________ Time: 08:58:00 AM PST US From: Mark Pennington Subject: Re: Yak-List: Swagelok Thank you Mr. Hill =F0=9F=91=8D=F0=9F=91=8D On Sun, Nov 1, 2020 at 11:55 AM Warren Hill wrote: > One additional item. If not already done. The bottom thread of the snot > bottle will need to be tapped to accept the input side of the Swagelock > valve, which I believe is =C2=BC-inch NPT. After completing the tap, be s ure to > completely wash out the many small metal fragments produced. It=99s helpful > to do the tap a little less than you think is needed and then screw int t he > Swagelock valve until it is tight. If a =C2=BC to =C2=BD turn more is nee ded to > properly align the value, run the tap just a little more. This way the > final valve position will not end up at some odd angle. > > - - - - - - - - - - > > Hello Mark, > > For the Yak-52, it's the Swagelok SS-43GM4-S4. > > For the CJ, a typical install requires a right angle adaptor and a > different right angle Swagelok valve. If you need this part number I =99ll get > it later today. > > Attached are some images. > > Warren > N464TW > > > On Nov 1, 2020, at 3:26 AM, Mark Pennington < > pennington.construction.inc.1@gmail.com> wrote: > > Jay > > Here is a photo I saved of the snot valve with a swagelock valve. > > At the time the post did not give a part number. > > Maybe someone will recognize the valve and share the part number > > Mark > N621 CJ > > > > > On Sat, Oct 31, 2020 at 8:14 PM Warren Hill wrote: > >> Both the Chinese adaptors and the Swagelok valves are =85=9B-27 NPT p ipe >> thread. >> >> >> On Oct 31, 2020, at 5:01 PM, William Geipel wrote: >> >> did you tap the new valve? size? >> >> >> On Nov 1, 2020, at 8:53 AM, Warren Hill wrote: >> >> Here is a picture of my CJ emergency on-off valve with adaptors that >> duplicate the original line positions. The Yak-52 probably requires >> different adaptors. The black handle valve for the main air is Swagelok >> part number SS-42GF2-A-WN2 and the emergency air red handle part number is >> SS-42GF2-A-RD-WN2. I suggest placing about 4 turns of nylon tape on the >> threads to lessen the likelihood of leaks. Replace and forget. >> >> Warren Hill >> N464TW >> Mesa, AZ >> >> >> >> >> On Oct 31, 2020, at 4:24 PM, jay-dub wrote: >> >> >> Please could someone tell me the spec of the Swagelok valves to replace >> the normal and emergency air valves. >> >> Also, the snot valves. >> >> Thanks from Lockdown, UK. [Rolling Eyes] >> >> -------- >> CJ and Yak-52 owner >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=499045#499045 >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message yak-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Yak-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/yak-list Browse Digests http://www.matronics.com/digest/yak-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.