Today's Message Index:
----------------------
 
     1. 05:24 PM - Re: strange A/H nuts & generator brushes? (AlaskaChang801)
     2. 07:52 PM - Re: Re: strange A/H nuts & generator brushes? (Justin Drafts)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:24:45 PM PST US
Subject: 
Re: strange A/H nuts & generator brushes?
From: 
"AlaskaChang801" <themilnes95@gmail.com>
      
      
      I just replaced my back AI and mine had 4mm nut and washer combo from the previous
      owner as the plate wasn't the stock one. Anyway, I understand the desire to
      keep the look stock etc, but if you can't get these from Doug Sapp, then you
      might have to buy alternative ones from MacMaster-Carr. They have M4 cap nuts,
      but not sure of the depth of thread so you may have to add a couple flat washers
      to take up the thickness if they bottom out in the cap. Or just buy 4mm Nylok
      nuts and go that way.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=499821#499821
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
07:52:26 PM PST US
From: 
Justin Drafts <draftsjust417@gmail.com>
Subject: 
Re: strange A/H nuts & generator brushes?
      
      Ya... that's a good plan-B.
      Great to not be in a rush or AOG...
      
      Thanks!
      Justin
      
      On Sun, Dec 27, 2020 at 5:59 AM AlaskaChang801 <themilnes95@gmail.com>
      wrote:
      
      >
      > I just replaced my back AI and mine had 4mm nut and washer combo from the
      > previous owner as the plate wasn't the stock one. Anyway, I understand the
      > desire to keep the look stock etc, but if you can't get these from Doug
      > Sapp, then you might have to buy alternative ones from MacMaster-Carr. They
      > have M4 cap nuts, but not sure of the depth of thread so you may have to
      > add a couple flat washers to take up the thickness if they bottom out in
      > the cap. Or just buy 4mm Nylok nuts and go that way.
      >
      >
      > Read this topic online here:
      >
      > http://forums.matronics.com/viewtopic.php?p=499821#499821
      >
      >
      








Other Matronics Email List Services




Post A New Message
  
yak-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Yak-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/yak-list
Browse Yak-List Digests
  
http://www.matronics.com/digest/yak-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --