Today's Message Index:
----------------------
1. 08:59 AM - Re: Hi all looking for 601 (Morgan Wadsworth)
2. 11:29 AM - Re: Piano hinge retainment (Scott Laughlin)
3. 11:44 AM - Re: Mufflers for Subaru engine (Gary Gower)
4. 01:00 PM - Re: Mufflers for Subaru engine (Aaron)
5. 04:53 PM - Re: Mufflers for Subaru engine (Michel Therrien)
6. 08:47 PM - Web site update (Michel Therrien)
7. 10:24 PM - Re: Piano hinge retainment (Gary Gower)
Message 1
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Hi all looking for 601 |
--> Zenith-List message posted by: "Morgan Wadsworth" <mwadsworth@factory53.com>
Noel & Yoshie,
If you go to www.controller.com, click on experimental aircraft, then choose
zenith and zenair there was a 601 80% complete for sale, there are also some
completed and flying 601's forsale as well.
Hope this helps...
Morgan IV
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com]On Behalf Of Noel &
Yoshie Simmons
Subject: Zenith-List: Hi all looking for 601
--> Zenith-List message posted by: "Noel & Yoshie Simmons"
<noel@blueskyaviation.net>
Hi all, Looking for a 601 un-completed kit for sale.
Must be a complete kit. Will look at kits with FWF's too.
Noel
Noel and Yoshie Simmons
Blue Sky Aviation, Inc.
"We do builder assistance!"
Toll Free: 866-859-0390
info@blueskyaviation.net
www.blueskyaviation.net
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Piano hinge retainment |
--> Zenith-List message posted by: "Scott Laughlin" <cookwithgas@hotmail.com>
Wayne:
I found something today that might be interesting to you. Check out this
pin retainment idea:
http://www.cooknwithgas.com/HingeSafety.jpg
This is one I had not seen.
Take care,
Scott Laughlin
www.cooknwithgas.com
----Original Message Follows----
From: "Wayne Glasser" <ku-tec@bigpond.net.au>
Subject: Zenith-List: Piano hinge retainment
--> Zenith-List message posted by: "Wayne Glasser" <ku-tec@bigpond.net.au>
Would constructors mind enlightening me as to what methods they have used to
retain the piano hinge wire on their elevators and trim tabs etc.
Regards
Wayne Glasser
Sydney - Australia
610XL 5075
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Mufflers for Subaru engine |
--> Zenith-List message posted by: Gary Gower <ggower_99@yahoo.com>
Michel,
I made one 3 years ago for another plane (Volksplane), I used normal
steel mesh and a 3" alum tube (one available), my idea was just to
test it, and change it (or trow it away) a few months, well, the sound
is very low and still is on the plane, I found the SS mesh a few weeks
later and is still in the shop... The VP was sold and is still flying
silently.
Saludos
Gary Gower
710
--- Michel Therrien <mtherr@yahoo.com> wrote:
> --> Zenith-List message posted by: Michel Therrien <mtherr@yahoo.com>
>
> I thought seriously about that for a while, but I
> can't find the SS mesh nor the 4" aluminum tube.
>
>
> --- Larry McFarland <larrymc@qconline.com> wrote:
> > --> Zenith-List message posted by: "Larry McFarland"
> > <larrymc@qconline.com>
> >
> > Michel,
> > Tony Bingilis's book Firewall Forward has a very
> > interesting Swiss Muffler
>
> =====
> ----------------------------
> Michel Therrien CH601-HD
> http://mthobby.pcperfect.com/ch601
> http://www.zenithair.com/bldrlist/profiles/mthobby
> http://pages.infinit.net/mthobby
>
>
>
>
>
>
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Mufflers for Subaru engine |
--> Zenith-List message posted by: "Aaron" <agustafson@chartermi.net>
The Subarus I have seen and heard are not very loud. In fact, one had about
15" straight pipes and even it was not objectionable. I'm using a two into
one collector with a single outlet. The inlets are blocked off on the ends
and enough 1/4" inch holes drilled in the side to equal the pipe ID.Hope to
test run in the next 60 days.
Aaron
----- Original Message -----
From: "Michel Therrien" <mtherr@yahoo.com>
Subject: Re: Zenith-List: Mufflers for Subaru engine
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Mufflers for Subaru engine |
--> Zenith-List message posted by: Michel Therrien <mtherr@yahoo.com>
One of my friends use two straight pipes (about 18"
long) with a closed (but not blocked) end and holes.
This approach is described in Bingelis (Firewall
Forward). His engine is an EA-82 and I must say that
on the ground, we can hear him coming and we instantly
recognize him. Noisy. I'd prefer something quieter
than that.
Michel
--- Aaron <agustafson@chartermi.net> wrote:
> --> Zenith-List message posted by: "Aaron"
> <agustafson@chartermi.net>
>
> The Subarus I have seen and heard are not very loud.
> In fact, one had about
> 15" straight pipes and even it was not
> objectionable. I'm using a two into
> one collector with a single outlet. The inlets are
> blocked off on the ends
> and enough 1/4" inch holes drilled in the side to
> equal the pipe ID.Hope to
> test run in the next 60 days.
> Aaron
> ----- Original Message -----
> From: "Michel Therrien" <mtherr@yahoo.com>
> To: <zenith-list@matronics.com>
> Subject: Re: Zenith-List: Mufflers for Subaru engine
> >
>
>
>
> Contributions
> any other
> Forums.
>
> latest messages.
> List members.
>
> http://www.matronics.com/subscription
> http://www.matronics.com/FAQ/Zenith-List.htm
> Digests:http://www.matronics.com/digest/zenith-list
> http://www.matronics.com/archives
> http://www.matronics.com/photoshare
> http://www.matronics.com/emaillists
>
>
>
>
>
=====
----------------------------
Michel Therrien CH601-HD
http://mthobby.pcperfect.com/ch601
http://www.zenithair.com/bldrlist/profiles/mthobby
http://pages.infinit.net/mthobby
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: Michel Therrien <mtherr@yahoo.com>
I worked on my web site a little bit yesterday and
this evening. Well I'd like to thank Don again for
hosting this. It is now taking 151 Mb of storage
space for the 3666 files of whose, 3470 are picture
files.
Michel
Do not archive
=====
----------------------------
Michel Therrien CH601-HD
http://mthobby.pcperfect.com/ch601
http://www.zenithair.com/bldrlist/profiles/mthobby
http://pages.infinit.net/mthobby
http://search.yahoo.com
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Piano hinge retainment |
--> Zenith-List message posted by: Gary Gower <ggower_99@yahoo.com>
Good idea, but MILES away from KIS...
Saludos
Gary Gower
701 912S
GDL, Mexico
Installing everything to the fuselage (gear, tail, controls...)
--- Scott Laughlin <cookwithgas@hotmail.com> wrote:
> --> Zenith-List message posted by: "Scott Laughlin"
> <cookwithgas@hotmail.com>
>
> Wayne:
>
> I found something today that might be interesting to you. Check out
> this
> pin retainment idea:
>
> http://www.cooknwithgas.com/HingeSafety.jpg
>
> This is one I had not seen.
>
> Take care,
>
> Scott Laughlin
> www.cooknwithgas.com
>
>
> ----Original Message Follows----
> From: "Wayne Glasser" <ku-tec@bigpond.net.au>
> To: <zenith-list@matronics.com>
> Subject: Zenith-List: Piano hinge retainment
> Date: Wed, 9 Apr 2003 07:03:07 +1000
>
> --> Zenith-List message posted by: "Wayne Glasser"
> <ku-tec@bigpond.net.au>
>
> Would constructors mind enlightening me as to what methods they have
> used to
> retain the piano hinge wire on their elevators and trim tabs etc.
>
> Regards
>
> Wayne Glasser
> Sydney - Australia
> 610XL 5075
>
>
>
>
>
>
>
>
http://search.yahoo.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|