---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Wed 05/14/03: 28 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:32 AM - Re: Re:Fiberglass Cowling (Dave Austin) 2. 05:41 AM - Re: Re:Fiberglass Cowling (ac6qj@earthlink.net) 3. 06:55 AM - Jabiru fwf kits (Jeff Small) 4. 07:05 AM - Rotec R2800 radial engine (Stephen Johnston) 5. 07:25 AM - In or out? (Jeff Small) 6. 07:39 AM - Re: Rotec R2800 radial engine (JNBOLDING1) 7. 08:09 AM - Re: Zenith List: Fiberglass Cowling (HINDE,FRANK (HP-Corvallis,ex1)) 8. 08:14 AM - Re: Rotec R2800 radial engine (David Barth) 9. 08:18 AM - Fuel line material (Bill Steer) 10. 08:31 AM - ch601 .dxf Files (Glenn Paul) 11. 09:36 AM - Re: Rotec R2800 radial engine (Hal Rozema) 12. 10:43 AM - Re: Rotec R2800 radial engine (Steve Dixon) 13. 11:25 AM - XL wing attachment (wizard-24@juno.com) 14. 11:35 AM - Re: ch601 .dxf Files (JNBOLDING1) 15. 11:51 AM - Re: XL wing attachment (David Barth) 16. 11:55 AM - Re: Fuel line material (HINDE,FRANK (HP-Corvallis,ex1)) 17. 11:59 AM - Re: Rotec R2800 radial engine (Hal Rozema) 18. 12:20 PM - Re: Fuel line material (Bryan Martin) 19. 12:36 PM - Re: XL wing attachment (HINDE,FRANK (HP-Corvallis,ex1)) 20. 12:39 PM - Re: XL wing attachment (Bryan Martin) 21. 12:40 PM - Re: Fuel line material (Benford2@aol.com) 22. 01:55 PM - Re: XL wing attachment (Dave Austin) 23. 04:36 PM - Re: XL wing attachment (Randall Thomure) 24. 05:02 PM - Re: ch601 .dxf Files (Larry McFarland) 25. 05:12 PM - Re: Rotec R2800 radial engine (Larry McFarland) 26. 05:16 PM - Re: XL wing attachment (wizard-24@juno.com) 27. 08:58 PM - ch701 flt sim files (Robert Hillebrand) 28. 09:00 PM - ch701 flt sim files (Robert Hillebrand) ________________________________ Message 1 _____________________________________ Time: 05:32:14 AM PST US From: "Dave Austin" Subject: Re: Zenith-List: Re:Fiberglass Cowling --> Zenith-List message posted by: "Dave Austin" I've followed this thread for a while now and thought I would add a word or two for what it's worth. The reason Chris puts the cowl inside is because the cowl is pressurized and pushes out against the fuse skin for a tight fit in flight. And you only need four fasteners!! Quick to remove!! If you put the cowl outside it will be necessary to put many more fasteners than Chris did to hold the cowl tight to the skin. But those planning a tight, low drag spinner/prop to cowl gap do have a problem.. Dave Austin 601HDS - 912 ________________________________ Message 2 _____________________________________ Time: 05:41:11 AM PST US From: ac6qj@earthlink.net Subject: Re: Zenith-List: Re:Fiberglass Cowling --> Zenith-List message posted by: ac6qj@earthlink.net Does anyone have pictures posted of the Jabiru FWF Kit on their 601? DO NOT ARCHIVE -- Best Regards, Ray Montagne Cupertino, CA ================================================================================ Zenith Aircraft Zodiac CH-601-XL builder #4939 Construction Log & Photos: Build Status: Rudder completed Elevator Completed Stabilizer Completed Flaps Completed Ailerons Completed Right Wing Under Construction ================================================================================ ________________________________ Message 3 _____________________________________ Time: 06:55:44 AM PST US From: "Jeff Small" Subject: Zenith-List: Jabiru fwf kits --> Zenith-List message posted by: "Jeff Small" >Does anyone have pictures posted of the Jabiru FWF Kit on their 601? Try http://www.usjabiru.com/ and click on Builders Photos, scroll to 601. You 701 guys can find some pics there too. Regards jeff ________________________________ Message 4 _____________________________________ Time: 07:05:35 AM PST US From: "Stephen Johnston" Subject: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: "Stephen Johnston" I have just started building a 701 airframe kit. I am trying to decide which engine to use. Are any of you 701 builders considering the Rotec R2800 radial engine? For information on the 110 H.P. radial engine click on the link below. Steve Johnston CH701 http://www.rotecradialengines.com/specs.htm ________________________________ Message 5 _____________________________________ Time: 07:25:31 AM PST US From: "Jeff Small" Subject: Zenith-List: In or out? --> Zenith-List message posted by: "Jeff Small" >The reason Chris puts the cowl inside is because >the cowl is pressurized and pushes out against the >fuse skin for a tight fit in flight. Dave, Sounds like good, solid reasoning to me but as Chris' design grows and guys stick different engines in the airframes, things can change. The entire inside of the cowl is probably pressurized for the Rotax and Subaru installations with the "guppy mouth" standard cowling, but Jabiru will remind users of its engines that the lower cowl area must have low pressure to ensure that cooling air travels over the tops of the heads and cylinder barrels and exits out the bottom. This also facilitates the airflow through the oil cooler if the cooler is located in the recommended position. Just ramming air in will not suffice for cooling if it can't get out and somewhere in Bingelis' books he talks about a formula that dictates more exit area than intake area - just to create such a low pressure area. XL builders using the 235 engine will need to fabricate a cooling plenum atop the engine as will you guys planning the Corvair installation. What you're doing is making sure the cool air goes where it should. Jabiru accomplishes this with fiberglass "RamDucts" that fit over each bank of cylinders. I watched Bill Morelli take off the top cowl of his HDS/Stratus every morning we flew to and from SnF. It was easy and he had everything open for preflight inspection. His cowl goes under the top skin (with a bit of a lip built in also, I think) and with the large opening of the standard cowl front he had sufficient "wiggle room" to make it work. Each installation will require differing approaches. Regards jeff ________________________________ Message 6 _____________________________________ Time: 07:39:58 AM PST US From: "JNBOLDING1" Subject: Re: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: "JNBOLDING1" >I have just started building a 701 airframe kit. I am trying to decide which engine to use. Are any of you 701 builders considering the Rotec R2800 radial engine? For information on the 110 H.P. radial engine click on the link below. > >Steve Johnston CH701 Steve, I and several others have decided on the Corvair, Zenith made some statements at Sun and Fun about putting a little more weight firewall forward on the 701 than the 200# max listed on the drawings. I haven't talked to them yet maybe some others have ???? If they weren't going to do it then I was going to get an aero engineer to do an analysis of the structure to see what, if anything, was necessary. ( I know a couple of them who work in the experimental arena)There are several 701s flying with Soobs and 0-200s and they are as heavy as a Corvair (I've read that the Soob is heavier) Lots of fellows are putting the Corvair in 601's . It's been around a long time flying airplanes ( almost 40 yrs) and is plentiful, cheap to build up, doesn't require a redrive as the torque is in the right rpm range, VERY smooth and will fit in the same space a VW will. If interested, give me a note off list and I'll give you some web sites to look at. LOW&SLOW John Bolding ________________________________ Message 7 _____________________________________ Time: 08:09:59 AM PST US From: "HINDE,FRANK (HP-Corvallis,ex1)" Subject: RE: Zenith-List: Zenith List: Fiberglass Cowling --> Zenith-List message posted by: "HINDE,FRANK (HP-Corvallis,ex1)" Your welcome...yes it was a nasty unforseen surprise to me too! -----Original Message----- From: Michel Therrien [mailto:mtherr@yahoo.com] Subject: Re: Zenith-List: Zenith List: Fiberglass Cowling --> Zenith-List message posted by: Michel Therrien I believe that Frank raised a very good point that I was about to oversee. Thanks Frank. Perhaps with the stock ZAC cowling and a small spinner it is not a problem. But I have a 10" spinner attached to a HP hub (SAE 1 bolt pattern). That will be a custom cowling with a cowling "plate" about 1/4" behind the hub. So, in this situation, I now think that it would be impossible to remove at least the bottom portion of the cowling. Michel --- Schallgren@aol.com wrote: > --> Zenith-List message posted by: > Schallgren@aol.com > > List: > > Frank says: "One thing, do not fit the cowl under > the fuse skin as it is > almost > impossible to remove it with the prop fitted." > > I have to disagree with that. .. ===== ---------------------------- Michel Therrien CH601-HD http://mthobby.pcperfect.com/ch601 http://www.zenithair.com/bldrlist/profiles/mthobby http://pages.infinit.net/mthobby __________________________________ http://search.yahoo.com advertising on the Matronics Forums. Share: Share photos & files with other List members. ________________________________ Message 8 _____________________________________ Time: 08:14:16 AM PST US From: David Barth Subject: Re: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: David Barth Wow! It would be interesting to see a 701 that "roared". The ones where I live kind of "whine". That would be awesome! David --- Stephen Johnston wrote: > --> Zenith-List message posted by: "Stephen > Johnston" > > I have just started building a 701 airframe kit. I > am trying to decide which engine to use. Are any of > you 701 builders considering the Rotec R2800 radial > engine? For information on the 110 H.P. radial > engine click on the link below. > > Steve Johnston CH701 > ===== David Barth 601 XL Plansbuilder Currently making parts. Stab, elevator and Rudder waiting for skins. Flaps and ailerons ready for inspection. __________________________________ http://search.yahoo.com ________________________________ Message 9 _____________________________________ Time: 08:18:27 AM PST US From: "Bill Steer" Subject: Zenith-List: Fuel line material --> Zenith-List message posted by: "Bill Steer" Hello, listers. I'm about to order the material for my fuel lines (601HD with leading edge tanks only) and am wondering what folks are using. I don't want fuel in the cockpit, so am going to use aluminum fuel lines. Is 5052-O the material of choice? How difficult is it to bend, since the ACS catalog lists it as "rigid?" Thanks for your help. Bill ________________________________ Message 10 ____________________________________ Time: 08:31:54 AM PST US From: "Glenn Paul" Subject: Zenith-List: ch601 .dxf Files --> Zenith-List message posted by: "Glenn Paul" I am a registerd plans owner (#6-3221) and am considering scratch building. Is there a way to scan the plans and convert them to the .dxf format so that they can be laser cut? Thanks Glenn J. Paul #6-3221 ________________________________ Message 11 ____________________________________ Time: 09:36:03 AM PST US From: Hal Rozema Subject: Re: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: Hal Rozema Jabiru also Ausy built: not geared, 3300 cc, 120 HP, 178 lbs w/ accessories about $13000 (basic engine) delivered US JNBOLDING1 wrote: > --> Zenith-List message posted by: "JNBOLDING1" > > >I have just started building a 701 airframe kit. I am trying to decide which engine to use. Are any of you 701 builders considering the Rotec R2800 radial engine? For information on the 110 H.P. radial engine click on the link below. > > > >Steve Johnston CH701 > > Steve, I and several others have decided on the Corvair, Zenith made some statements at Sun and Fun about putting a little more weight firewall forward on the 701 than the 200# max listed on the drawings. I haven't talked to them yet maybe some others have ???? If they weren't going to do it then I was going to get an aero engineer to do an analysis of the structure to see what, if anything, was necessary. ( I know a couple of them who work in the experimental arena)There are several 701s flying with Soobs and 0-200s and they are as heavy as a Corvair (I've read that the Soob is heavier) Lots of fellows are putting the Corvair in 601's . It's been around a long time flying airplanes ( almost 40 yrs) and is plentiful, cheap to build up, doesn't require a redrive as the torque is in the right rpm range, VERY smooth and will fit in the same space a VW will. If interested, give me a note off list and I'll give you some web sites to look at. LOW&SLOW John Bolding > ________________________________ Message 12 ____________________________________ Time: 10:43:38 AM PST US From: "Steve Dixon" Subject: Re: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: "Steve Dixon" Doesn't the Jabiru turn a bit fast for the 701? I was thinking the ideal prop speed for the 701 was around 2500 RPM. That would make the round beast just about perfect, although a bit on the heavy side. I would guess the price is a bit on the heavy side too. With 3: 2 gearing and 110 HP that engine would undoubtedly produce enough torque to outperform any Jab in a 701. Hey, that's my story----and I'm stickin' to it. Isn't having all these choices wonderful? Steve Dixon Do Not Archive ----- Original Message ----- From: "Hal Rozema" Subject: Re: Zenith-List: Rotec R2800 radial engine > --> Zenith-List message posted by: Hal Rozema > > Jabiru also Ausy built: not geared, 3300 cc, 120 HP, 178 lbs w/ accessories about $13000 (basic engine) delivered US > > JNBOLDING1 wrote: > > > --> Zenith-List message posted by: "JNBOLDING1" > > > > >I have just started building a 701 airframe kit. I am trying to decide which engine to use. Are any of you 701 builders considering the Rotec R2800 radial engine? For information on the 110 H.P. radial engine click on the link below. > > > > > >Steve Johnston CH701 > > > > Steve, I and several others have decided on the Corvair, Zenith made some statements at Sun and Fun about putting a little more weight firewall forward on the 701 than the 200# max listed on the drawings. I haven't talked to them yet maybe some others have ???? If they weren't going to do it then I was going to get an aero engineer to do an analysis of the structure to see what, if anything, was necessary. ( I know a couple of them who work in the experimental arena)There are several 701s flying with Soobs and 0-200s and they are as heavy as a Corvair (I've read that the Soob is heavier) Lots of fellows are putting the Corvair in 601's . It's been around a long time flying airplanes ( almost 40 yrs) and is plentiful, cheap to build up, doesn't require a redrive as the torque is in the right rpm range, VERY smooth and will fit in the same space a VW will. If interested, give me a note off list and I'll give you some web sites to look at. LOW&SLOW John Bolding > > > > ________________________________ Message 13 ____________________________________ Time: 11:25:39 AM PST US Subject: Zenith-List: XL wing attachment From: wizard-24@juno.com --> Zenith-List message posted by: wizard-24@juno.com I'm in the process of attaching the wings on my 601XL, and I'm pulling my hair out trying to figure this out. And anyone who has seen me knows darn well that I can ill afford to lose any more hair. The drawing is very unclear as to how best get the wings attached correctly, and of course the builder's manual doesn't even mention anything about it. I have the wing spars inserted into the center spar and temporarily bolted, so that part is done. What I can't figure out is: 1. How do I determine the angle of incidence to use (hope I'm using the right terms)? 2. How do I assure that the leading edge of the wings are perpendicular to the fuselage center line? (if that indeed is what I am supposed to do....). There's some mention of using string lines....but there's no string length dimensions. It seems to me that running two strings of the same length from the tail to the wing tips won't ensure that the wings are perpendicular...that would only ensure that the wings are at the same angle -- which might not be the correct angle. I'm rambling here, mostly because I don't know what I'm doing. But this would seem to be an important step, and I don't want to screw it up. I fly crooked enough without the help of the plane. I know the HDS & HD models have a different wing configuration, but hopefully there's some tidbit of info I'm missing. Thanks, Mike Fortunato 601XL The best thing to hit the internet in years - Juno SpeedBand! Surf the web up to FIVE TIMES FASTER! ________________________________ Message 14 ____________________________________ Time: 11:35:24 AM PST US From: "JNBOLDING1" Subject: Re: Zenith-List: ch601 .dxf Files --> Zenith-List message posted by: "JNBOLDING1" >I am a registerd plans owner (#6-3221) and am considering scratch building. > >Is there a way to scan the plans and convert them to the .dxf format so that >they can be laser cut? > >Thanks > >Glenn J. Paul >#6-3221 > I can't speak for the 601 guys but if you did that with the 701 plans you would have a substantial pile of aluminum that would be suitable for making smaller parts with. Since the 701 drawings have been converted to CAD there have been several hundred corrections, most minor some not. It seems that Zenair is getting a handle on it (the 701) as the last go round was pretty uneventful. Scratch building and kit building are different animals (I've done both an RV3 and a Glasair) The scratch builders swap more time and less money for their "kit" and have little trouble generally making the minor adjustments. Remaking a part means slipping a piece of alum into the form block and hammering out a new one in 10-15 min instead of firing off a check to Zenith and gnashing your teeth waiting on the mailman. OK guys I've said my piece about scratch building, lets hear from the other side. LOW&SLOW John ________________________________ Message 15 ____________________________________ Time: 11:51:49 AM PST US From: David Barth Subject: Re: Zenith-List: XL wing attachment --> Zenith-List message posted by: David Barth Hi Mike. I just guessing here since I am not there yet but for squaring you could check using pythagorus theorem from geometry. It only works using right triangles. If you can 1. measure from a spot on the leading edge to the centerline of the AC and call that X and (has to be measured right along the leading edge) 2. measure from the intersection of the leading edge line with the centerline to a spot on the tail and call that Y. Then the measurement from the spot on the leading edge to the spot on the tail is Z If the leading edge is in fact perpendicular to the CL of the AC then Z should be equal to the square root of (x squared plus y squared) Is the Z measured the same as the Z calculated? I am certain there must be a better (simpler) way but I can't think of one right now. Good luck David > 2. How do I assure that the leading edge of > the wings are perpendicular > to the fuselage center line? (if that indeed is what > I am supposed to > do....). There's some mention of using string > lines....but there's no > string length dimensions. It seems to me that > running two strings of the > same length from the tail to the wing tips won't > ensure that the wings > are perpendicular...that would only ensure that the > wings are at the same > angle -- which might not be the correct angle. > ===== David Barth 601 XL Plansbuilder Currently making parts. Stab, elevator and Rudder waiting for skins. Flaps and ailerons ready for inspection. __________________________________ http://search.yahoo.com ________________________________ Message 16 ____________________________________ Time: 11:55:10 AM PST US From: "HINDE,FRANK (HP-Corvallis,ex1)" Subject: RE: Zenith-List: Fuel line material --> Zenith-List message posted by: "HINDE,FRANK (HP-Corvallis,ex1)" I used 3003-0 in 1/4" AFTER the fuel pumps only, which I installed in the last "bay" of the inner wing between the nose ribs, bolt through the bottom wing skin. This was as close as I could reasonably get the pumps to the tanks. I used 3/8ths rubber hose on the suction side of the pumps. The 3003-0 forms easily and as long as you don't stand on it will be just fine. Your only running at 5psi or so anyway. Frank 601 HDS Stratus (modified valve guides) 290 hours -----Original Message----- From: Bill Steer [mailto:bsteer@gwi.net] Subject: Zenith-List: Fuel line material --> Zenith-List message posted by: "Bill Steer" Hello, listers. I'm about to order the material for my fuel lines (601HD with leading edge tanks only) and am wondering what folks are using. I don't want fuel in the cockpit, so am going to use aluminum fuel lines. Is 5052-O the material of choice? How difficult is it to bend, since the ACS catalog lists it as "rigid?" Thanks for your help. Bill advertising on the Matronics Forums. Share: Share photos & files with other List members. ________________________________ Message 17 ____________________________________ Time: 11:59:18 AM PST US From: Hal Rozema Subject: Re: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: Hal Rozema Jab 3300 max torque is 107 fp @ 2500 rpm i'm using at 68" Prince P-Tip pitched for that. Smaller flat plate area. Not that it makes that much difference on a draggy bird. We'll just see. When I'm running engine tests, I will measure static thrust from this combination and publish it along with initial flight numbers. Hal Steve Dixon wrote: > --> Zenith-List message posted by: "Steve Dixon" > > Doesn't the Jabiru turn a bit fast for the 701? I was thinking the ideal > prop speed for the 701 was around 2500 RPM. That would make the round beast > just about perfect, although a bit on the heavy side. I would guess the > price is a bit on the heavy side too. With 3: 2 gearing and 110 HP that > engine would undoubtedly produce enough torque to outperform any Jab in a > 701. Hey, that's my story----and I'm stickin' to it. > > Isn't having all these choices wonderful? > > Steve Dixon > > Do Not Archive > > ----- Original Message ----- > From: "Hal Rozema" > To: > Subject: Re: Zenith-List: Rotec R2800 radial engine > > > --> Zenith-List message posted by: Hal Rozema > > > > Jabiru also Ausy built: not geared, 3300 cc, 120 HP, 178 lbs w/ > accessories about $13000 (basic engine) delivered US > > > > JNBOLDING1 wrote: > > > > > --> Zenith-List message posted by: "JNBOLDING1" > > > > > > > >I have just started building a 701 airframe kit. I am trying to decide > which engine to use. Are any of you 701 builders considering the Rotec R2800 > radial engine? For information on the 110 H.P. radial engine click on the > link below. > > > > > > > >Steve Johnston CH701 > > > > > > Steve, I and several others have decided on the Corvair, Zenith made > some statements at Sun and Fun about putting a little more weight firewall > forward on the 701 than the 200# max listed on the drawings. I haven't > talked to them yet maybe some others have ???? If they weren't going to do > it then I was going to get an aero engineer to do an analysis of the > structure to see what, if anything, was necessary. ( I know a couple of them > who work in the experimental arena)There are several 701s flying with Soobs > and 0-200s and they are as heavy as a Corvair (I've read that the Soob is > heavier) Lots of fellows are putting the Corvair in 601's . It's been around > a long time flying airplanes ( almost 40 yrs) and is plentiful, cheap to > build up, doesn't require a redrive as the torque is in the right rpm range, > VERY smooth and will fit in the same space a VW will. If interested, give me > a note off list and I'll give you some web sites to look at. LOW&SLOW > John Bolding > > > > > > > > ________________________________ Message 18 ____________________________________ Time: 12:20:33 PM PST US From: Bryan Martin Subject: Re: Zenith-List: Fuel line material --> Zenith-List message posted by: Bryan Martin 3003-0 is the stuff to use. It's much easier to work with, cheaper and plenty strong enough for fuel systems. I am using 3/8" O.D., the chart in the ACS catalog lists the max working pressure as 520 psi with a safety factor of 2. It's sold in coils so the shipping will be less also. -- Bryan Martin N61BM, CH 601 XL, Stratus Subaru. Airframe construction complete. Working on instrument panel, electrical and interior. do not archive. on 5/14/03 11:26 AM, Bill Steer at bsteer@gwi.net wrote: > Hello, listers. I'm about to order the material for my fuel lines (601HD with > leading edge tanks only) and am wondering what folks are using. I don't want > fuel in the cockpit, so am going to use aluminum fuel lines. Is 5052-O the > material of choice? How difficult is it to bend, since the ACS catalog lists > it as "rigid?" > > Thanks for your help. > > Bill ________________________________ Message 19 ____________________________________ Time: 12:36:10 PM PST US From: "HINDE,FRANK (HP-Corvallis,ex1)" Subject: RE: Zenith-List: XL wing attachment --> Zenith-List message posted by: "HINDE,FRANK (HP-Corvallis,ex1)" So In the HD(S) the center wing section is straight (at least I hope it was) so If you take two tape measures from the spar (or the rear spar) on the out board edge to the tail tip and make that dimension the same, the wing MUST be square to the fuse...This assumes the fuse is straight. That's what I did and I got it to within a millimeter as accuratly as I could measure. I know of at least one plane that is nearly an inch out, and it still flys just fine....Not good enough for MY plane though. Frank -----Original Message----- From: wizard-24@juno.com [mailto:wizard-24@juno.com] Subject: Zenith-List: XL wing attachment --> Zenith-List message posted by: wizard-24@juno.com I'm in the process of attaching the wings on my 601XL, and I'm pulling my hair out trying to figure this out. And anyone who has seen me knows darn well that I can ill afford to lose any more hair. The drawing is very unclear as to how best get the wings attached correctly, and of course the builder's manual doesn't even mention anything about it. I have the wing spars inserted into the center spar and temporarily bolted, so that part is done. What I can't figure out is: 1. How do I determine the angle of incidence to use (hope I'm using the right terms)? 2. How do I assure that the leading edge of the wings are perpendicular to the fuselage center line? (if that indeed is what I am supposed to do....). There's some mention of using string lines....but there's no string length dimensions. It seems to me that running two strings of the same length from the tail to the wing tips won't ensure that the wings are perpendicular...that would only ensure that the wings are at the same angle -- which might not be the correct angle. I'm rambling here, mostly because I don't know what I'm doing. But this would seem to be an important step, and I don't want to screw it up. I fly crooked enough without the help of the plane. I know the HDS & HD models have a different wing configuration, but hopefully there's some tidbit of info I'm missing. Thanks, Mike Fortunato 601XL The best thing to hit the internet in years - Juno SpeedBand! Surf the web up to FIVE TIMES FASTER! advertising on the Matronics Forums. Share: Share photos & files with other List members. ________________________________ Message 20 ____________________________________ Time: 12:39:39 PM PST US From: Bryan Martin Subject: Re: Zenith-List: XL wing attachment --> Zenith-List message posted by: Bryan Martin 1. If the spar center section was installed properly with the wing jigs, the angle of incidence will be correct, just align the rear Z with the rear attach plate. 2. The most important thing is to get the wings attached at the same angle. The bolts in the spar will hold the wings close enough to perpendicular, a slight deviation from this angle will make no difference. I measured from each wing tip to the centerline at a point near the tail and they were within 1/16" with just the spar bolts installed. I just clamped them at the rear attach plate and drilled the holes. -- Bryan Martin N61BM, CH 601 XL, Stratus Subaru. Airframe construction complete. Working on instrument panel, electrical and interior. do not archive. on 5/14/03 2:32 PM, wizard-24@juno.com at wizard-24@juno.com wrote: > 1. How do I determine the angle of incidence to use (hope I'm using the > right terms)? > > 2. How do I assure that the leading edge of the wings are perpendicular > to the fuselage center line? (if that indeed is what I am supposed to > do....). There's some mention of using string lines....but there's no > string length dimensions. It seems to me that running two strings of the > same length from the tail to the wing tips won't ensure that the wings > are perpendicular...that would only ensure that the wings are at the same > angle -- which might not be the correct angle. ________________________________ Message 21 ____________________________________ Time: 12:40:30 PM PST US From: Benford2@aol.com Subject: Re: Zenith-List: Fuel line material --> Zenith-List message posted by: Benford2@aol.com In a message dated 5/14/2003 9:19:09 AM Mountain Daylight Time, bsteer@gwi.net writes: > > Hello, listers. I'm about to order the material for my fuel lines (601HD > with leading edge tanks only) and am wondering what folks are using. I > don't want fuel in the cockpit, so am going to use aluminum fuel lines. Is > 5052-O the material of choice? How difficult is it to bend, since the ACS > catalog lists it as "rigid?" > > Thanks for your help. > > Bill > What the heck does aluminum lines do to keep the fuel out of the cockpit????? Ben Haas N801BH. ________________________________ Message 22 ____________________________________ Time: 01:55:50 PM PST US From: "Dave Austin" Subject: Re: Zenith-List: XL wing attachment --> Zenith-List message posted by: "Dave Austin" When I fitted the HDS wings to my HD, I just eyeballed the rivet line from the wingtip to the fuselage. If that was straight I figured that would be good.. Dave Austin 601HDS - 912 ________________________________ Message 23 ____________________________________ Time: 04:36:57 PM PST US From: "Randall Thomure" Subject: RE: Zenith-List: XL wing attachment --> Zenith-List message posted by: "Randall Thomure" Dave, I am many hundreds of hours before tackling this task, but I did find drawing 6-S-3 that details a 3 step procedure to align and square the wings relative to the plane. The drawing is towards the back of the drawing bundle. If you can't locate it maybe ZAC can furnish. Randall Thomure 601XL - Working on the tail -----Original Message----- From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com]On Behalf Of Dave Austin Subject: Re: Zenith-List: XL wing attachment --> Zenith-List message posted by: "Dave Austin" When I fitted the HDS wings to my HD, I just eyeballed the rivet line from the wingtip to the fuselage. If that was straight I figured that would be good.. Dave Austin 601HDS - 912 ________________________________ Message 24 ____________________________________ Time: 05:02:30 PM PST US From: "Larry McFarland" Subject: Re: Zenith-List: ch601 .dxf Files --> Zenith-List message posted by: "Larry McFarland" Glenn, The short answer to that is no because the scale is not consistent. I used a plasma cutter and trimmed the last inch to maintain properties of the 6061-T6, which does save time in blanking. Larry McFarland - 601hds - 6-4117 in 4th year. at www.macsmachine.com ----- Original Message ----- From: "Glenn Paul" Subject: Zenith-List: ch601 .dxf Files > --> Zenith-List message posted by: "Glenn Paul" > > I am a registerd plans owner (#6-3221) and am considering scratch building. > > Is there a way to scan the plans and convert them to the .dxf format so that > they can be laser cut? > > Thanks > > Glenn J. Paul > #6-3221 > > ________________________________ Message 25 ____________________________________ Time: 05:12:33 PM PST US From: "Larry McFarland" Subject: Re: Zenith-List: Rotec R2800 radial engine --> Zenith-List message posted by: "Larry McFarland" Subject: Zenith-List: Rotec R2800 radial engine > --> Zenith-List message posted by: "Stephen Johnston" > > I have just started building a 701 airframe kit. I am trying to decide which engine to use. Are any of you 701 builders considering the Rotec R2800 radial engine? For information on the 110 H.P. radial engine click on the link below. > > Steve Johnston CH701 > > http://www.rotecradialengines.com/specs.htm Steve, The light structure of the 701 would make one think by hanging so much on the nose you'd be better building an 801. The 701 climbs as good as it's going to with 65-80 hp. Adding more wt to get HP just increases your glide angle but not much the climb angle. And the stress goes way up. Larry ________________________________ Message 26 ____________________________________ Time: 05:16:40 PM PST US Subject: Re: Zenith-List: XL wing attachment From: wizard-24@juno.com --> Zenith-List message posted by: wizard-24@juno.com > drawing 6-S-3 that details a 3 step procedure to align and square > the wings relative to the plane. I must have the old version of 6-S-3, because there isn't squat about details, so maybe I'll check with ZAC top see if there's an update (I checked the web site and there's nothing there). But many thanks to those who offered their input -- some very good ideas. I also plan to check all the RV web sites out there, since I'm told the wings attach in the same manner as the XL. Mike Fortunato do not archive The best thing to hit the internet in years - Juno SpeedBand! Surf the web up to FIVE TIMES FASTER! ________________________________ Message 27 ____________________________________ Time: 08:58:55 PM PST US From: Robert Hillebrand Subject: Zenith-List: ch701 flt sim files --> Zenith-List message posted by: Robert Hillebrand --------------------------------- ________________________________ Message 28 ____________________________________ Time: 09:00:48 PM PST US From: Robert Hillebrand Subject: Zenith-List: ch701 flt sim files --> Zenith-List message posted by: Robert Hillebrand Can anyone tell me hoe to get the fltsim 2000 files to work? I dloaded from zac to my fltsim directory and then unzipped them but still have no show in the select an aircraft. No ch701 ---------------------------------